• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.558-564
• /
• 2001

General vehicle is evaluated by its acceleration, fuel economy, NVH (Noise, Vibration and Harshness) and subjective (Launching feel) performance. The first step to enhance its performance is to know how much each component affects on the vehicle performance. It is very important to know what is the key factor of the component among many specifications. Hydraulic torque converter can be expressed by means of its performance curve (torque ratio and capacity factor). In this paper, the key factor of torque converter, which affect vehicle performance, are explored by using Taguchi method.

• 터널과지하공간
• /
• 제26권5호
• /
• pp.441-453
• /
• 2016

본 연구에서는 분진을 저감시킬 수 있고 균질한 품질을 확보하는 데 적합한 2성분 박층 뿜칠 라이너(TSL)를 개발하고 그 성능을 평가하였다. 2성분 TSL 시작품의 인장강도는 분말 1성분 TSL보다 다소 낮게 나타났으나, 높은 연성으로 인해 파괴 시의 신장률이 크게 측정되었다. 이외에도 EFNARC(2008)에서 제시하고 있는 성능기준들을 만족하였으며, 두께 3 mm로 피복한 코팅 압축시험 결과, 재령 28일의 평균 압축강도가 50% 이상 향상되는 것으로 확인되었다. 시험타설을 통해 본 연구에서 개발된 2성분 TSL 시작품에 적합한 타설장비를 도출하였으며, 실제 현장시공을 통해 2성분 TSL 타설 시의 분진과 리바운드가 극히 미미함을 확인하였다. 2성분 TSL의 타설속도는 $60m^2/hr$이었으며 일반적인 뿜칠 방수 멤브레인과 비교할 때 빠른 경화 특성을 나타내었다.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권2호
• /
• pp.45-52
• /
• 2002

Load modeling is classified into two methods according to approaching method, so called the measurement and component-based method. The measurement method is to model the load characteristics measured directly at substations and feeders. But it is difficult to measure continuously load characteristics from naturally occurring. system variation. The component-based method consists of the fellowing process; component load modeling, composition rate estimation and aggregation of component loads, etc. In this paper, the characteristic experiment of component loads was performed to obtain data for the component load modeling as the component-based method. At first, representative component loads were selected by the proposed method considering the accuracy of load modeling and the performance possibility of component load experiment in the laboratory. Also an algorithm was Proposed to identify the reliability of data obtained from the component load characteristic experiments. In addition, the results were presented as the case studies.

• 한국건설순환자원학회논문집
• /
• 제10권4호
• /
• pp.506-513
• /
• 2022

본 논문에서는 탄소중립을 위한 일환의 연구로써 3가지의 산업부산물을 활용하여 시멘트 사용량에 대하여 80 %까지 대폭 대체한 4성분계 고유동 콘크리트의 품질특성을 평가하였다. 평가결과, 다량의 산업부산물을 혼합하여 시멘트 사용량을 80% 이상 감소시킨 배합에서 목표 성능을 만족하는 품질을 얻을 수 있었으며, 유동특성, 역학특성 및 내구특성의 경우 기존 기준 배합과 비교하여 다소 성능이 감소되는 경향이 나타났지만 소요성능 수준 이상의 성능을 만족할 수 있는 것으로 판단된다. 종합적으로 고려할 경우 고로슬래그 미분말 혼합량이 큰 4성분계 고유동 콘크리트가 상대적으로 우수한 성능을 보였다.

• 한국경영과학회지
• /
• 제36권1호
• /
• pp.39-55
• /
• 2011

Process monitoring has been emphasized for the monitoring of complex system such as chemical processing industries to achieve the efficiency enhancement, quality management, safety improvement. Recently, ICA (Independent Component Analysis) based MSPC (Multivariate Statistical Process Control) was widely used in process monitoring approaches. Moreover, DICA (Dynamic ICA) has been introduced to consider the system dynamics. However, the existing approaches show the limitation that their performances are strongly dependent on the statistical distributions of control variables. To improve the limitation, we propose a novel approach for process monitoring by integrating DICA and LOF (Local Outlier Factor). In this paper, we aim to improve the fault detection rate with the proposed method. LOF detects local outliers by using density of surrounding space so that its performance is regardless of data distribution. Therefore, the proposed method not only can consider the system dynamics but can also assure robust performance regardless of the statistical distributions of control variables. Comparison experiments were conducted on the widely used benchmark dataset, Tennessee Eastman process (TE process), and showed the improved performance than existing approaches.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2549-2552
• /
• 1999

The fictitious power theory in time domain is very easy to understand, but power analyzing time of active power is increased, because power is analyzed using signal techniques based on the correlation between voltage and current waveforms. Also, conventional methods in time/frequency domain to evaluate the compensation performance of active power filters are not provided easy solutions. So, the authors have previously proposed 3-D current coordinates which is composed into active component, fundamental reactive component and distorted component of nonlinear loads current. This method has excellent performance, but can not evaluate the characteristics of nonlinear load current whether inductive or capacitive. Therefore, To overcome problems mentioned previously, this paper deals with the simple instantaneous power theory and the modified 3-D current coordinates for evaluating the compensation performance of active power filters. To confirm the validity, active power filters simulator is developed using C-language. From the simulation, results are discussed their utility.

• 대한전기학회논문지
• /
• 제39권11호
• /
• pp.1174-1182
• /
• 1990

A hgih efficiency and good dynamic performance drive system of an induction motor is presented in this paper using vector control technique. If the induction motor is driven under light loads with rated flux, the iron loss is excessively large compared with the copper loss, resulting in poor motor efficiency. High efficiency drive of an induction motor can be achieved by adjusting the flux level which leads the total motor loss to be a minimum value. Generally reducing the flux degrades the dynamic performance, but the dynamic performance of the proposed system is also maintained high. If the d-axis is coincident with rotor flux phasor in synchronous rotating reference frame, the stator current can be decoupled as flux component and torque component. At steady state, the developed motor torque is proportional to the product of the flux and torque component. The combination of the two components minimizing the motor loss could be found with numerical method. As the procedure to obtain the optimal combination is too hard, it is found experimentally. The system block diagram is suggested for maximum efficiency control. The proposed system is studied through digital simulation and verified with experiment. The experimental results show the possiblity of a high efficiency drive with good dynamic performance of maximum efficiency control.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제10권4호
• /
• pp.220-228
• /
• 2002

The cool-down performance after soaking is very important in an automotive air-conditioning system and is considered as a key design variable. Therefore, transient characteristics of each system component are essential to the preliminary design as well as steady-state performance. The objective of this study is to develop a computer simulation model and ostinato theoretically the transient performance of an automotive air-conditioning system. To do that, the mathematical modelling of each component, such as compressor, condenser, receiver/drier, expansion valve, and evaporator, is presented first of all. The basic balance equations about mass and energy are used in modelling. For detailed calculation, condenser and evaporator are divided into many sub-sections. Each sub-section is an elemental volume for modelling. In models of expansion valve and compressor, dynamic behaviors are not considered in this analysis, but the quasisteady state ones are just considered, such as the relation between mass flow rate and pressure drop in expansion device, polytropic process in compressor, etc. Also it is assumed that there are no heat loss and no pressure drop in discharge, liquid, and suction lines. The developed simulation model is validated by comparing with the laboratory test data of an automotive air-conditioning system. The overall time-tracing properties of each component agreed well with those of test data in this case.

• 설비공학논문집
• /
• 제25권6호
• /
• pp.331-337
• /
• 2013

An experimental study on the performance of a liquid electric component cooling system was performed. The thermal resistance and pressure drop at a heat sink were measured, for aluminum waterblocks with four different internal shapes, with either smooth surface, porous media filling, or with fins of 5 mm height, or of 7 mm height. The fins had 0.5 mm thickness, and the gap between the fins was 0.5 mm. The waterblock internal dimension was $36.5{\times}36.5{\times}7mm$. Compared with the waterblock with smooth surface, the thermal resistance reduction was 11%, 46%, and 42% for waterblocks with porous media filling, 5 mm, and 7 mm fins, respectively. A new dimensionless parameter was suggested to evaluate the waterblock performance, with the simultaneous consideration of thermal resistance and pressure drop. The performance of the waterblock with fins of 5 mm height was best by parameter.

• 식품보건융합연구
• /
• 제6권2호
• /
• pp.23-26
• /
• 2020

Active and therapeutic sport recovery is becoming a popular and important component in approving performance for pro and recreational athletes alike. It is also helping in the realm of injury prevention. In the search of finding modalities that are widely effective, natural, and safe, acupuncture is a viable and cost-effective treatment for helping athletes achieve this goal. More direct related research is needed, but testimonials from pro athletes and the body of research that currently exists provides powerful evidence on acupunctures ability to help with enhancing recovery. Specializing in acupuncture and exercise science, Chris integrates acupuncture into musculoskeletal rehabilitation therapy or fitness training for pain modulation, speedy recovery, and enhanced performance. Clients can choose to focus on one-on-one corrective exercise therapy, manual and massage therapy, or acupuncture. However, for best results, Chris recommends all three. Other modalities that he uses in therapy are acu-taping, herbal therapy, nutrition supplementation, cupping, guasha, and stretching techniques. The corrective exercise component is one-on-one body balancing management, focusing on strength and conditioning, post physical rehab - exercise therapy, integrative sport specific exercise, weight loss, core strengthening, dynamic lumbar stabilization, active recovery techniques, and myo-fascial release techniques. The acupuncture component focuses on sport injuries, myofascial pain, peripheral neuropathy, arthritis, facial rejuvenation, stress, smoking cessation, addiction detoxification program, weight management, sport recovery and performance.