• 소성∙가공
• /
• 제18권1호
• /
• pp.26-38
• /
• 2009

It was reported that the semi-solid forming process has many advantages over the conventional forming process, such as a long die life, good mechanical properties and energy savings. It is very important, however, to control liquid segregation to gain mechanical property improvement of materials. During forming process, rheology material has complex characteristics, thixotropic behavior. Also, difference of velocity between solid and liquid in the semi-solid state material makes a liquid segregation and specific stress variation. Therefore, it is difficult for a numerical simulation of the rheology process to be performed. General plastic or fluid dynamic analysis is not suitable for the behavior of rheology material. The behavior and stress of solid particle in the rheology material during forging process is affected by viscosity, temperature and solid fraction. In this study, compression experiments of aluminum alloy were performed under each other tool shape which is rectangle shape(square array), rectangle shape(hexagonal array), and free shape tool. In addition, the dynamics behavior compare with Okano equation to power law model which is viscosity equation.

• 한국식품과학회지
• /
• 제29권5호
• /
• pp.932-938
• /
• 1997

Changes in viscosity and dynamic theological properties of Job's-tears were measured by Bohlin dynamic tester as a function of moisture, and measurement was performed within a linear viscoelastic range. The result of the shear stress vs shear rate of Job's-tears at different moisture contents $(50{\sim}75%)$ was applied to mathematical models and Herschel-Bulkley model showed the highest correlation coefficient. Lower moisture content (55%) produced higher yield stress and consistency index, but lower flow behavior index, whereas higher moisture content showed reverse effects. Job's-tears with $50{\sim}70%$ moisture contents showed a higher storage modulus (G') than loss modulus (G') at all frequencies, showing a higher concentrated polymer characteristics. However, higher moisture content (>75%) showed crossover point between G' and G', and frequency dependency. As the moisture content was increased, the amount of viscoelastic properties such as G', G', complex viscosity decreased during heating, and initial temperature and miximum value of viscoelastic properties shifted to higher temperatures, representing the moisture-dependence of Job's-tears upon theological properties.

• 한국식품영양과학회지
• /
• 제44권9호
• /
• pp.1407-1413
• /
• 2015

본 연구는 '고운' 품종으로 제조한 감자가루 분산액의 농도(3, 4, 5, 6, 7%, w/w)에 따른 유변학적 및 페이스팅 특성에 대하여 평가하였다. 감자가루 분산액은 전단담화 거동(n=0.41~0.55)을 나타냈으며, 감자가루 농도가 증가함에 따라 점조도 지수(n), 겉보기 점도(${\eta}_{a,100}$), Casson 항복응력(${\sigma}_{oc}$)값이 증가하는 경향을 나타내었다. 또한 동적 점탄 특성 측정 결과에 의하면 감자가루 분산액은 약한 겔과 같은 거동을 보여주었으며 G'과 G" 값들은 감자가루 농도와 진동수(${\omega}$)가 증가함에 따라 증가하는 경향을 나타내었다. Cox-Merz 중첩원리는 감자가루 분산액에 잘 적용되지 않았다. RVA에 의한 페이스팅 특성은 감자가루 농도가 증가할수록 peak viscosity, trough viscosity, final viscosity, set back viscosity, break down viscosity 값이 유의적으로 증가하였다.

• Korea-Australia Rheology Journal
• /
• 제11권3호
• /
• pp.219-223
• /
• 1999

The effects of the transreactions on the rheological properties have been found in the poly(ethylene 2, 6-naphthalate) (PEN) and poly (ethylene terephthalate) (PET) blends. The rheological properties were very much dependent on the blend compositions, which, in turn, were related to extent of the reactions. In particular, a blend with 50/50 wt% composition exhibits an unusual and remarkable decrease in complex viscosity and it may be related to the randomness of the copolymer structure through transreactions. It has been identified by investigating the extent of transreactions and block length of the copolymer from the (ethylene 2, 6-naphthalate) (EN) and (ethylene terephthalate) (ET) units from $^1{H}$ n.m.r. spectra.

• 한국표면공학회지
• /
• 제46권2호
• /
• pp.87-92
• /
• 2013

Viscosities of $LaCl_3$-CsCl binary melts were measured by the capillary method over the range of their liquidus temperatures to about 1200 K. The cell constant were determined by using pure water. The results obtained are summerized as follows: Viscosities of melted $LaCl_3$ were decreased with the content of CsCl for all over the composition range of binary melts. Composition versus viscosity relation for the binary melt showed a non-linear relationship from the additivity line and the deviations showed a maximum value at about 60 mol% CsCl. This suggest the existence of the complex ion of $LaCl_4{^-}$ in the melt. Activation energy for the viscous flow of the binary melts decreased monotonously with the increasing content of CsCl after a few increasement till 40 mol% CsCl. All of these results were the resemble with the viscosities of $LaCl_3$-NaCl binary melts.

• 소성∙가공
• /
• 제31권5호
• /
• pp.290-295
• /
• 2022

Recently, the use of high-tech ceramic parts in functional electronic parts, automobile parts and semiconductor equipment parts is increasing. These ceramics materials are required to have high reproducibility, reliability, large size and complex shapes. The researchers initiated the work to develop a new shaping method called gel casting, which allows high performance ceramic materials with a complex shape to be produced. The manufacturing process parameters of gel casting include uniform mixing of the initiator, bubble removal, and slip injection. In this study, we analyzed the dispersion and gelation characteristics according to the change in the additive content of the alumina slurry in the gel casting process. The alumina slurry for gel casting was prepared by mixing a solvent, a monomer and a dispersant through a ball mill. Alumina powder and a gelation initiator were added to the mixed solution, and ball milling was performed for 24 hours. A viscosity of 6,435 cps and a stable zeta potential value were obtained under the conditions of alumina powder content of 55 vol% and dispersant 2.0 wt%. After curing for 12 hours by adding aps 0.1wt%, TEMED 0.2wt%, and Monomer 3, 5wt%, it was possible to separate from the molding cup, confirming that the gelation was completed.

• 한국세라믹학회지
• /
• 제35권8호
• /
• pp.783-790
• /
• 1998

The characterization of the complexation reaction of PVA and Al(III) ion at different pH and the sint-ering behaviour of UO2 containing the PVA-Al(III) complexes were investigated. Compared with pure PVA powder the complexed PVA-Al(III) powder had compacter shape and lower decomposition temperature The major phase of PVA-Al(III) complex decomposed at 90$0^{\circ}C$ was $\alpha$-Al2O3 The PVA-Al(III) complex formed at pH 9 had the lowest relative viscosity the highest Al content of 36% and the smallest particle size of 19${\mu}{\textrm}{m}$ While the pure UO2 pellet appeared with bimodal one. The grain size of the pure UO2 pellet was 7${\mu}{\textrm}{m}$ but that of the PVA-Al(III) complex added UO2 pellet was increased up to 36${\mu}{\textrm}{m}$ The largest grain size was ob-tained when the PVA-Al(III) complex formed at pH9 was added and the PVA-Al(III) complex formed at pH 11 had the greatest effect on increasing pore size.

• 펄프종이기술
• /
• 제42권5호
• /
• pp.74-82
• /
• 2010

Curtain stability without curtain contraction is critical for a successful operation in curtain coating, and this can be influenced by the change in particle dynamics and rheological properties of coating colors. In this study, polyvinyl alcohol (PVA) and carboxymethyl cellulose (CMC) were added to control the rheology of GCC based curtain coating colors. Surface tension was increased slightly with increasing content of cobinder. Shear-thinning of viscosity was more pronounced for the CMC containing GCC coating colors. Complex modulus decreased when small amount of PVA was used as a cobinder, but it increased in other coating colors. Extensional viscosity was increased with increasing of the cobinder content, but CMC was more effective. Results indicate that pigment interaction with PVA is different from that with CMC. Dispersibility of coating colors was improved due to steric stabilization when small amounts of PVA was used, but flocculation occurred by bridging when the amount of PVA was increased. Dispersibility of coating colors was improved when small amount of CMC was added, while flocculation was observed by depletion effect when the concentration of CMC was increased in coating colors. Addition of cobinders at proper levels gave positive effects both in rheological properties and curtain stability. On the other hand, excessive amount of cobinders caused particle flocculation and this resulted in rheological and curtain stablity problems.

• 구강회복응용과학지
• /
• 제24권3호
• /
• pp.311-316
• /
• 2008

Calcium phosphate cement (CPC)는 우수한 생체 친화성을 바탕으로 치과 및 의과 쪽에서 성공적인 bone substitute로 사용되어 왔다. 긴 경화시간 및 washout tendency 등 CPC의 단점을 개선하기 위해 다양한 종류의 경화액 및 첨가제등에 대한 연구가 이루어졌다. 그러나 첨가제의 종류에 따른 CPC paste의 점탄성을 정량적으로 비교한 연구는 많지 않다. 이 연구에서는 2% hydroxyprophyl methylcellulose (HPMC)와 35% polyacrylic acid (PAA)의 두 가지 경화액과 혼합된 CPC의 유변학적 성질을 관찰하고 비교하고자 하였다. Dicalcium phosphate dihydrate (DCPD)를 2% HPMC 및 35% PAA와 각각 1:1의 분액비로 30초간 섞은 후 cone and plate geometry를 가지는 rheometer를 사용하여 frequency sweep test와 time sweep test를 통해 shear storage modulus (G'), shear loss modulus (G''), 그리고 complex viscosity (${\eta}^*$)를 측정하였다. 2% HPMC군과 35% PAA군의 complex viscostiy의 차이를 Mann-whitney test with Bonferroni's collection을 사용하여 분석하였다. 실험결과 2% HPMC 및 35% PAA 군 모두에서 shear thinning과 yield behavior등 pseudoplastic property를 보였으며 complex viscosity는 HPMC 군에서 PAA 군보다 통계적으로 유의성 있게 높았다. (p<0.05).

• Journal of Pharmaceutical Investigation
• /
• 제29권4호
• /
• pp.295-307
• /
• 1999

Using a Rheometries Fluids Spectrometer (RFS II), the dynamic viscoelastic properties of aqueous poly(ethylene oxide) (PEO) solutions in small amplitude oscillatory shear flow fields have been measured over a wide range of angular frequencies. The angular frequency dependence of the storage and loss moduli at various molecular weights and concentrations was reported in detail, and the result was interpreted using the concept of a Deborah number De. In addition, the experimentally determined critical angular frequency at which the storage and loss moduli become equivalent was compared with the calculated characteristic time (or its inverse value), and their physical significance in analyzing the dynamic viscoelastic behavior was discussed. Finally, the relationship between steady shear flow and dynamic viscoelstic properties was examined by evaluating the applicability of some proposed models that describe the correlations between steady flow viscosity and dynamic viscosity, dynamic fluidity, and complex viscosity. Main results obtained from this study can be summarized as follows: (1) At lower angular frequencies where De<1, the loss modulus is larger than the storage modulus. However, such a relation between the two moduli is reversed at higher angular frequencies where De>l, indicating that the elastic behavior becomes dominant to the viscous behavior at frequency range higher than a critical angular frequency. (2) A critical angular frequency is decreased as an increase in concentration and/or molecular weight. Both the viscous and elastic properties show a stronger dependence on the molecular weight than on the concentration. (3) A characteristic time is increased with increasing concentration and/or molecular weight. The power-law relationship holds between the inverse value of a characteristic time and a critical angular frequency. (4) Among the previously proposed models, the Cox-Merz rule implying the equivalence between the steady flow viscosity and the magnitude of the complex viscosity has the best validity. The Osaki relation can be regarded to some extent as a suitable model. However, the DeWitt, Pao and HusebyBlyler models are not applicable to describe the correlations between steady shear flow and dynamic viscoelastic properties.