• Asian Pacific Journal of Cancer Prevention
• /
• 제16권16호
• /
• pp.6981-6986
• /
• 2015

Background: Breast cancer is the most common cancer in women. One way to decrease the burden of this cancer is early detection through mammography. This study compared the effectiveness of two different educational methods for teachers' uptake of mammography based on the Health Belief Model. Materials and Methods: The current study was a randomised trial of 120 teachers over 40 years old in two groups receiving multimedia or group education, both based on the Health Belief Model. Participants completed questionnaires before, immediately and three months after educational intervention. Mammography was evaluated before and after educational intervention. Results: The participants in the two groups were demographically similar. Comparison showed no difference noted in the scores of knowledge, perceived barriers, susceptibility, and severity constructs between two groups (p > 0.05). Health motivation and benefit were perceived to be higher in the group education compared to the multimedia group. There was a significant difference in mammography between two groups after the intervention (p= 0.003). Conclusions: Planning and implementation of educational program based on the Health Belief Model can raise knowledge and increase participation in mammography especially with group education.

• 한국환경과학회지
• /
• 제12권6호
• /
• pp.605-613
• /
• 2003

In order to make use of the protection effect against wind by the vegetation, it examined whether it should make what vegetation form and arrangement using the 2-dimensional non-hydrostatic model. When the foliage shielding factor increases, it becomes hard to take in protection effect against wind in a residential section. When it makes height of vegetation high, it becomes hard to take in protection effect against wind with height. In the comparison in the case where vegetation high is gradually made low toward wind-stream from a vegetation, and the case of making it low gradually, although former tends to receive the protection effect against wind by the vegetation, attenuation of wind velicity becomes large. In the comparison in the case where foliage shielding factor and distribution of density of leaf are gathered gradually toward wind-stream from a vegetation. It has been understood to evaluate to height the influence that the vegetation multi-layer model by which the heat revenue and expenditure in the direction of the vegetation height is considered is used, and to characterize the vegetation group by the parameter setting.

• 자원ㆍ환경경제연구
• /
• 제9권2호
• /
• pp.349-371
• /
• 2000

Data Envelopment Analysis model is a linear programming based technique for measuring the relative performance of organizational units where the presence of multiple inputs and outputs makes comparison difficult. A common measure for relative efficiency is weighted sum of outputs divided by weighted sum of inputs. DEA model allows each unit to adopt a set of weight that shows it in the most favorable light in comparison to the other unit. In this paper, we present the mathematical background and characteristics of DEA model, and give a short case study where we apply the DEA model to evaluate the relative efficiencies of 51 global electricity companies. The technical efficiency and scale efficiency are also to be investigated. Generating capacity and the number of employees are used for input data, and revenue, net profit and electricity sales are used for output data. We find that the companies with 100% relative efficiency are only 9 among 51 electricity companies. And the technical and scale efficiency of KEPCO is 98.7% and 78.89%, respectively. This means that the inefficiency of KEPCO is caused by the scale inefficiency. The analysis shows that the employees should be decreased by 15% at minimum to get the 100% efficiency. The result suggests that KEPCO needs the structural reform to improve the efficiency.

• Computers and Concrete
• /
• 제17권1호
• /
• pp.29-51
• /
• 2016

Tension-stiffening is the contribution of concrete between the cracks to carry tensile stresses after cracking in Reinforced Concrete (RC) members. In this paper, a tension-stiffening model has been proposed for computationally efficient nonlinear analysis of RC flexural members subjected to service load. The proposed model has been embedded in a typical cracked span length beam element. The element is visualized to consist of at the most five zones (cracked or uncracked). Closed form expressions for flexibility and stiffness coefficients and end displacements have been obtained for the cracked span length beam element. Further, for use in everyday design, a hybrid analytical-numerical procedure has been developed for nonlinear analysis of RC flexural members using the proposed tension-stiffening model. The procedure yields deflections as well as redistributed bending moments. The proposed model (and developed procedure) has been validated by the comparison with experimental results reported elsewhere and also by comparison with the Finite Element Method (FEM) results. The procedure would lead to drastic reduction in computational time in case of large RC structures.

• 한국관개배수논문집
• /
• 제14권2호
• /
• pp.207-213
• /
• 2007

For sustainable development at a watershed, environment friendly site-specific management practices need to be developed and implemented. The soil and Water Assessment Tool(SWAT)model has been world-wide used to estimate stream flow, sediment, and nonpoint source pollutant loads, and effects on water quality of different management practices. In this study, the SWAT model was used to estimate the flow resources at Hwacheon areas using Digital Elevation Model(DEM),Land use, precipitation ,wind ,maximum and minimum temperature, solar radiation, humidity of watershed The R2 value and EI value for the comparison of SWAT estimated flow and measured flow were 0.87 and 0.67 respectively for calibration period, and the R2 value and E1 value for validation were 0.75 and 0.67 respectively. The comparison results show what the SWAT model is applicable to simulate hydrology behaviors at this study watershed.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 2009년도 IWAIT
• /
• pp.606-611
• /
• 2009

This paper describes a method for achieving a novel design within a class of 3D objects that would create a preferred impression on users. Physical parameters of the 3D objects that might strongly contribute to their visual impressions are sought through computational investigation of the impression ratings obtained for learning samples. "Car body" was selected as the class of 3D objects to be investigated. A morphable 3D model of car bodies that describes the variations in appearance using a smaller number of parameters was obtained. Based on each car body's rating for the impression of speediness obtained by paired comparison, the visual impression was transformed by manipulating the parameters defined in the morphable 3D model. The validity of the proposed method was confirmed by psychological experiments. A new scheme is also proposed to properly re-sample a novel object of a peculiar shape so that such an object could also be represented by the morphable 3D model.

• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.753-762
• /
• 2012

The ratcheting characteristics of cylindrical shell under cyclic axial loading are investigated. The specimens are subjected to stress-controlled cycling with non-zero mean stress, which causes the accumulation of plastic strain or ratcheting behavior in continuous cycles. Also, cylindrical shell shows softening behavior under symmetric axial strain-controlled loading and due to the localized buckling, which occurs in the compressive stress-strain curve of the shell; it has more residual plastic strain in comparison to the tensile stress-strain hysteresis curve. The numerical analysis was carried out by ABAQUS software using hardening models. The nonlinear isotropic/kinematic hardening model accurately simulates the ratcheting behavior of shell. Although hardening models are incapable of simulating the softening behavior of the shell, this model analyzes the softening behavior well. Moreover, the model calculates the residual plastic strain close to the experimental data. Experimental tests were performed using an INSTRON 8802 servo-hydraulic machine. Simulations show good agreement between numerical and experimental results. The results reveal that the rate of plastic strain accumulation increases for the first few cycles and then reduces in the subsequent cycles. This reduction is more rapid for numerical results in comparison to experiments.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.202-215
• /
• 2015

This paper investigates the stability and performance of model predictive controlled active-front-end (AFE) rectifiers for energy storage systems, which has been increasingly applied in power distribution sectors and in renewable energy sources to ensure an uninterruptable power supply. The model predictive control (MPC) algorithm utilizes the discrete behavior of power converters to determine appropriate switching states by defining a cost function. The stability of the MPC algorithm is analyzed with the discrete z-domain response and the nonlinear simulation model. The results confirms that the control method of the active-front-end (AFE) rectifier is stable, and that is operates with an infinite gain margin and a very fast dynamic response. Moreover, the performance of the MPC controlled AFE rectifier is verified with a 3.0 kW experimental system. This shows that the MPC controlled AFE rectifier operates with a unity power factor, an acceptable THD (4.0 %) level for the input current and a very low DC voltage ripple. Finally, an efficiency comparison is performed between the MPC and the VOC-based PWM controllers for AFE rectifiers. This comparison demonstrates the effectiveness of the MPC controller.

• 응용통계연구
• /
• 제34권4호
• /
• pp.623-632
• /
• 2021

본 연구에서는 여러가지 시계열 모형 중 평활법(가법계절지수, 승법계절지수), 계절 ARIMA 모형, ARARCH 그리고 AR-GARCH 회귀모형을 이용하여 최대 전력수요를 예측하는 방법을 연구하였다. 이 때 가중 평균모형으로 추세를 갖는 시계열 모형과 온도에 대한 회귀 모형을 적절한 가중치로 예측 정확도를 높이는 방법도 연구하였다. 결과적으로 AR-GARCH 회귀모형으로 예측하는 것이 가중 우수함을 보였다.

• 한국정밀공학회지
• /
• 제13권11호
• /
• pp.132-142
• /
• 1996

This paper presents a technique to model and control a manipulator which has a flexible link and moves in a vertical plane. The flexible link is modeled as an Euler-Bernoulli Beam. Elastic deformation of the flexible link is represented using the assumed modes method. A comparison function which satisfies all geometric and natural boundary conditions of a cantilever beam with an end mass is used as an assumed mode shape. Lagrange's equation is utilized for the development of a discretized model. This paper presents a simple technique to improve the correctness of the developed model. The final model including the shortening effect due to elastic deformation correlates very well with experimental results. The free body motion simulation shows that two assumed modes for the representation of the elastic deformation is proper in terms of the model size and correctness. A control algorithm is developed using PID control technique. The proportional, integral and derivative control gains are determined based on dominant pole placement method with a rigid one-link manipulator. A position control simulation shows that the control algorithm can be used to control the position and residual oscillation of the flexible one-link manipulator effectively.