• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1847-1855
• /
• 2012

A 1V 1.6-GS/s 6-bit flash analog-to-digital converter (ADC) with a clock calibration circuit is proposed. A single track/hold circuit with a bootstrapped analog switch is used as an input stage with a supply voltage of 1V for the high speed operation. Two preamplifier-arrays and each comparator composed of two-stage are implemented for the reduction of analog noises and high speed operation. The clock calibration circuit in the proposed flash ADC improves the dynamic performance of the entire flash ADC by optimizing the duty cycle and phase of the clock. It adjusts the reset and evaluation time of the clock for the comparator by controlling the duty cycle of the clock. The proposed 1.6-GS/s 6-bit flash ADC is fabricated in a 1V 90nm 1-poly 9-metal CMOS process. The measured SNDR is 32.8 dB for a 800 MHz analog input signal. The measured DNL and INL are +0.38/-0.37 LSB, +0.64/-0.64 LSB, respectively. The power consumption and chip area are $800{\times}500{\mu}m2$ and 193.02mW.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11C
• /
• pp.1085-1097
• /
• 2009

We present a structure and design method of the D8PSK modem compatible with the VDL mode-2 standard and performance test results of the developed modem. In VDL mode-2, the raised cosine filter is used only in the transmitter and a general low pass filter is used in the receiver. Consequently, we can not achieve ISI reduction but can have better spectrum characteristics. Although there is 1~2 dB performance degradation with an un-matched filter compared to that with a matched filter, it is more important to minimize adjacent channel interference in narrow band communications. The transmit signal is generated digitally to avoid the problems(I/Q imbalance and DC offset etc.) of analog modulators. In addition the digital down converter using digital IF sampling technique is adopted for the receiver. This paper contains the overall configuration, design method and simulation results based in part on the previously proposed structures and algorithms. It is confirmed that the modem transmits and receives messages successfully at a speed of max. 870 km/h over ranges of up to 310 km through the ground and in-flight communication tests.

• Applied Microscopy
• /
• v.34 no.1
• /
• pp.13-21
• /
• 2004

The high voltage electron microscope (HVEM) newly installed in KBSI is an advanced transmission electron microscope capable of atomic resolution (${\leq}1.2{\AA}$ point-to-point resolution) together with high titling function (${\pm}60^{\circ}$), which are suitable to do 3-dimensional atomic imaging of a specimen. In addition, the instrument can be controlled by remote operation system, named as 'FasTEM' for the HVEM, which is favorable to overcome some environmental obstacles resulting from the direct operation. The FasTEM remote operation system has been established between the headquarter of KBSI in Daejeon and the Seoul branch. The server system in the headquarter has been connected with a portable client console system in the Seoul branch using an advanced internet resource, 'KOREN' of 155 Mbps grade. Most of the HVEM functions essential to do remote operation are available on the portable client console. The experiment to acquire the high resolution image of [001] Au has been achieved by excellent transmission of control signals and communication with the HVEM. Real-time reaction like direct operation, such as controls of the illumination and projection parameters, acquisition and adjustment of each detector signal, and electrical steering of each motor-driven system has been realized in remote site. It is positively anticipated that the first remote operation of HVEM in conjunction with IT infraengineering plays a important role in constructing the network based e-Science Grid in Korea for national user s facilities.

• The Research Journal of the Costume Culture
• /
• v.8 no.5
• /
• pp.648-659
• /
• 2000

Through this study I would like to examine the meaning system of the symbolized codes related with real costume figures of the abstract concept of the style of the mourning ceremonial dress in Chosun Dynasty as a variable cause of communication through non-language method by the structural analysis of coding of the ceremonial dress style and the meaning system of the codes centering on the traditional book of funeral etiquette dealing with hueneral cereony in the period. To achieve this purpose, I have used the symbolic theory of constructive concept by F. de Saussure, cultural notation theory of Roland Barthes & Umberto Eco, and structural style of costumes by Myung-Sook Han. The result of the study is as follows. 1. As Chosun Dynasty was a society in which people considered courtesy so much important and practiced the basic Confucian ideas of the three bonds and five moral disciplines in human relations, the characteristic of funeral rites in Chosun Dynasty consists in expression of the thoughts of moral ethics & relative systems and systems of clan rules, etc which was a langue determining the symbols of mourning ceremony dress because the mourning ceremony dress in the period should have the feature of a langue. The mourning ceremonial dresses in the period had five grades of the consume and the grades were determined to be classified into five levels according to the clan system of the chief mourner with sang, ha bang. And the method of the association of the mourning ceremonial dress codes had the six principles of Chinchin, Jonjon, Myoungboon, Chulip, Changyu, and Jongbok. 2. Regarding the mourning ceremonial costumes in Korean society, the meaning of funeral ceremony was expressed by the signifier and materials of the mourning costumes in the society. During the process of the funeral, the intangible feeling of condolence was the expression of mourning and the tangible mourning ceremonial dress was the signal with the lamentation meaning. Especially, characters and patterns were removed from the mourning ceremonial dresses in spite of their function of symbols and the styles of costumes were emphasized. Especially the meaning of condolences was symbolized by attachment of some small pieces of cloth on the upper garments. Hemp was mainly emphasized to be the material of the costumes and some different meanings showed according to the quality of the material hemp. The mourning ceremonial dresses were distinguished from ordinary dresses, which were emphasized because they gad some symbolic meaning of the mourning. 3. Considering the association of the synthetic relations of the costumes from the viewpoint that the mourning ceremonial dresses would be classified according to a system, the symbolization of them were avaliable by sex according to how to combine them and there were no distinction between social classes in the society.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.1
• /
• pp.123-132
• /
• 1999

In this paper, a quadratic sigmoid neural equalizer(QSNE) is proposed to improve the performance of conventional neural equalizer in terms of bit error probability by using a quadratic sigmoid function as the activation function of neural networks. Conventional neural equalizers which have been used to compensate for nonlinear distortions adopt the sigmoid function. In the case of sigmoid neural equalizer, each neuron has one linear decision boundary. So many neurons are required when the neural equalizer has to separate complicated structure. But in case of the proposed QSNF and quadratic sigmoid neural decision feedback equalizer(QSNDFE), each neuron separates decision region with two parallel lines. Therefore, QSNE and QSNDFE have better performance and simpler structure than the conventional neural equalizers in terms of bit error probability. When the proposed QSNDFE is applied to communication systems and digital magnetic recording systems, it is an improvement of approximately 1.5dB~8.3dB in signal to moise ratio(SNR) over the conventional decision feedback equalizer(DEF) and neural decision feedback equalizer(NDFE). As intersymbol interference(ISI) and nonlinear distortions become severer, QSNDFE shows astounding SNR shows astounding SNR performance gain over the conventional equalizers in the same bit error probability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.428-435
• /
• 2004

With the rapid and wide-spread use of cellular telephones much attention has been focussed on propagation in the urban area crowed with buildings and houses. It is often surrounded by hills, forests, and mountains. The importance of surface scattering intereference between transmitters and receivers on the rough surfaces has been interested and investigated. Therefore, a prediction method is necessary to estimate the influence of rough surfaces on microwave radio propagation. Moreover, most of the mobile communications are performed based on the digital communication system rather than the analog one. In this case, we must pay more careful attention to the signal delay caused by the phase delay due to the multi-path propagation. In this paper we have analyzed numerically scattering of electromagnetic waves from building walls by using FVTD(Finite Volume Time Domain) method. We consider three different types of rough surfaces such as periodic, random, and composite structures. We calculate the bistatic normalized radar cross section (NRCS) for horizontal and vertical polarization, and we take account of the conventional optical reflection which corresponds to the n-th Bragg reflection for periodic structures. In addition, we investigated what conditions are needed in order to be able to ignore the higher order Bragg reflection for the periodic structures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.630-643
• /
• 2001

In this paper, the performance of a Multi-Carrier DS-CDMA system with Hybrid $SC/MRC- L_{c}/L$ diversity in the multipath Rayleigh fading environment is analyzed and compared with that of a Wideband DS-CDMA system. Each carriers of the number of the input diversity branches in the Multi-Carrier DS-CDMA system is L and among L, the branches of $L_c$ are chosen to be maximum-ratio-combined. And the diversity outputs are coherent-detected and despread by the correlator of each carrier. As the result, we have known that the structure of the Wideband DS-CDMA system with Hybrid $SC/MRC-L_{c}/L$ diversity reception becomes simple due to no synchronization of bit or phase and in terms of the error performance, the performance of Hybrid $SC/MRC- L_{c}/L$ diversity is better than that of selection diversity, but worse than that of MRC diversity. Moreover, the performance of a Multi-Carrier DS-CDMA system is better than that of a Wideband DS-CDMA system in multipath Rayleigh fading channel since Hybrid $SC/MRC- L_c/L$ diversity can obtain gain from each diversity branch. In case four carriers are used and required BER is $10^{-6}$ in wireless data communication, Hybrid SC/MRC-2/4 diversity can increase more 17 users than Hybrid SC/MRC-2/3 diversity because the better input branches can be selected through increase of input branches.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.5
• /
• pp.796-805
• /
• 2000

A 30GHz band low noise amplifier module, which has linear gain of 30dB and noise figure of 2.6dB, for 30GHz satellite communication transponder was developed by use of MMIC and thin film MIC technologies. Two kinds of MMIC circuits were used for the low noise amplifier module, the first one is ultra low noise MMIC circuit and the other is wideband and high gain MMIC circuit. The pHEMT technology with 0.15$mu extrm{m}$ of gate length was applied for MMIC fabrication. Thin film microstrip lines on alumina substrate were used to interconnect two MMIC chips, and the thick film bias circuit board were developed to provide the stabilized DC bias. The input interface of the low noise amplifier module was designed with waveguide type to receive the signal from antenna directly, and the output port was adopted with K-type coaxial connector for interface with the frequency converter module behind the low noise amplifier module. Space qualified manufacturing processes were applied to manufacture and assemble the low noise amplifier module, and space qualification level of environment tests including thermal and vibration test were performed for it. The developed low noise amplifier was measured to show 30dB of minimum gain, $\pm$0.3dB of gain flatness, and 2.6dB of maximum noise figure over the desired operating frequency range from 30 to 31 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.154-161
• /
• 2011

This paper presents a compact integrated transceiver module for 2.4 GHz band applications using Low Temperature Co-fired Ceramic(LTCC) technology. The implemented transceiver module is divided into an RF Front-End Module (FEM) part and a transceiver IC chip part. The RF FEM part except an SPDT switch and DC block capacitors is fully embedded in the LTCC substrate. The fabricated RF FEM has 8 pattern layers and it occupies less than $3.3\;mm{\times}5.2\;mm{\times}0.4\;mm$. The measured results of the implemented RF FEM are in good agreement with the simulated results. The transceiver IC chip part consists of signal line, power line and transceiver IC for 2.4 GHz band communication system. The fabricated transceiver module has 9 layers including three inner grounds and it occupies less than $12\;mm{\times}8.0\;mm{\times}1.1\;mm$. The implemented transceiver module provides an output power of 18.1 dBm and a sensitivity of -85 dBm.

• Imaging Science in Dentistry
• /
• v.33 no.2
• /
• pp.113-119
• /
• 2003

Purpose : To evaluate the relationship between morphometric analysis of bone microstructure from digital radiographic image and trabecular bone strength. Materials and Methods : One hundred eleven bone specimens with 5 mm thickness were obtained from the mandibles of 5 pigs. Digital images of specimens were taken using a direct digital intraoral radiographic system. After selection of ROI (100 × 100 pixel) within the trabecular bone, mean gray level and standard deviation were obtained. Fractal dimension and the variants of morphometric analysis (trabecular area, periphery, length of skeletonized trabeculae, number of terminal point, number of branch point) were obtained from ROI. Punch sheer strength analysis was performed using Instron (model 4465, Instron Corp., USA). The loading force (loading speed 1 mm/min) was applied to ROI of bone specimen by a 2 mm diameter punch. Stress-deformation curve was obtained from the punch sheer strength analysis and maximum stress, yield stress, Young's modulus were measured. Results: Maximum stress had a negative linear correlation with mean gray level and fractal dimension significantly (p<0.05). Yield stress had a negative linear correlation with mean gray level, periphery, fractal dimension and the length of skeletonized trabeculae significantly (p < 0.05). Young's modulus had a negative linear correlation with mean gray level and fractal dimension significantly (p < 0.05). Conclusions : The strength of cancellous bone exhibited a significantly linear relationship between mean gray level, fractal dimension and morphometric analysis. The methods described above can be easily used to evaluate bone quality clinically.