• 한국분무공학회지
• /
• 제14권3호
• /
• pp.103-108
• /
• 2009

This research investigated spray characteristics using LPG fuel under compression ignition to contribute to develop a high efficiency LPG fuel is an environmentally-friendly fuel since it emits lower $CO_2$ compare to other conventional fuels. In order to observe spray process, a high speed digital camera and high pressure common-rail injector were applied. Using the spray behaviors of LPG and diesel fuel from the experiment, this research analyzed the mixing process of air-fuel mixture numerically with FLUENT 6.3 when LPG and diesel fuel injected directly into the cylinder while compression stroke occurs. Spray characteristics of LPG fuel was investigated by using numerical method, in which KH-RT model was adapted for phase change. As a result of numerical analysis, this work found out that LPG spray has a wider mixing formation and uniform diffusion of air-fuel mixture compare to diesel.

• 한국분무공학회지
• /
• 제14권3호
• /
• pp.109-116
• /
• 2009

The purpose of this study is the experimental and numerical investigation on the DME spray characteristics in the combustion chamber according to the injection timing in a common-rail injection system. The visualization system consisted of the high speed camera with metal halide lamp was used for analyzing the spray characteristics such as spray development processes and the spray tip penetration in the free and in-cylinder spray under various ambient pressure. In order to observe the spray characteristics as a function of injection timing, the piston head shape of re-entrant type was created and the fuel injected into the chamber according to various distance between nozzle tip and piston wall in consideration of injection timing. Also, the spray and evaporation characteristics in the cylinder was calculated by using KlVA-3V code for simulating spray development process and spray tip penetration under real engine conditions. It was revealed that the high ambient pressure of 3 MPa was led to delay the spray development and evaporation of DME spray. In addition, injected sprays after BTDC 20 degrees entered the bowl region and the spray at the BTDC 30 degrees was divided into two regions. In the calculated results, the liquefied spray tip penetration and fuel evaporation were shorter and more increased as the injection timing was retarded, respectively.

• 한국자동차공학회논문집
• /
• 제18권2호
• /
• pp.97-103
• /
• 2010

The four combustion stages in a diesel engine have close correlation among them. Especially, the ignition delay period has significant effect on the following combustion stage. And the period is also one of inevitable combustion processes in the diesel engine. For example, the diesel knocking is a well-known phenomenon due to the long ignition delay period. The interval of the ignition delay period is affected by the mixture formation process in the cylinder. However, in the case of the D.I. diesel engine, the available duration to make the mixture formation of air-fuel is very short. In addition, the means of the mixture formation mainly depends on the injection characteristics and properties of the fuel. It is difficult to make complete mixture. Therefore, an early stage of combustion is violent, which leads to the weakness of noise and vibration. In this study, using the visible engine, we measured the ignition delay period by photo sensor which detect occurrence of flame and presented the factors of the injection characteristics such as kinds of injection system, the injection pressure and the injection timing. The relation between the ignition delay period and cylinder pressure diagram which was concurrently obtained was also estimated.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.105-113
• /
• 2014

Spray and combustion process with waste cooking oil (WCO) biodiesel and commercial diesel were analyzed in an optically-accessible single-cylinder compression ignition diesel engine equipped with a high pressure common-rail injection system. Direct imaging method was applied to investigate spray and combustion characteristics. From the mie-scattering results, it was verified that WCO biodiesel had a longer injection delay compared to diesel. Spray tip penetration length of WCO biodiesel was longer and spray angle was narrower than those of diesel due to poor atomization characteristics. In terms of combustion, WCO biodiesel showed later start of combustion, while flame was vanished more rapidly. Analysis of flame luminosity showed that WCO biodiesel combustion had lower intensity and lasted for shorter duration.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.55-64
• /
• 2014

This work was investigated on pilot injection strategy of blended fuels(Diesel-DME) for combustion and emissions in a single cylinder direct injection compression ignition engine. Diesel and DME were blended by the method of weight ratio. Weight ratios for diesel and DME were 95:05 and 90:10 respectively. dSOI between main and pilot injection timing was varied. A total amount of injected fuels(single injection) was adjusted to obtain the fixed BMEP as 4.2 bar in order to compare with the fuel conditions. Also, the amount of pilot injection fuel was varied by 5%, 10% and 20% of total injection fuel. The engine was equipped with common rail and injection pressure is 700 bar at 1200 rpm. As a result, when mixing ratio increase, indicated thermal efficiency was increased in comparison with DD 100 and CO, THC and smoke were lower than DD 100. The influence of reducing NOx by pilot injection was more effective than DD 100. When pilot injection quantity increase, abrupt increase of NOx was occured at pilot injection quantity of 20%.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.169-177
• /
• 2015

In this study we investigated the regeneration methods for the lean $NO_x$ trap (LNT) catalyst in a 2.2L direct injection diesel engine. The regeneration methods were 1) in-cylinder post fuel injection and 2) external fuel injection strategy. The in-cylinder post fuel injection method uses in-cylinder injectors with the addition of the post fuel injection to supply enough reductants such as CO, $H_2$, THC. The external fuel injection method was enabled by installing a fuel injector with a wide spray angle before the LNT catalyst. Through the engine experiment, the $NO_x$ conversion efficiency, the amount of reductant exhaust gases, fuel consumption, and temperature behavior in the LNT catalyst were evaluated and compared for the two regeneration methods.

• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.93-100
• /
• 2005

Stringent emission regulations and increasing demands on reductions of noise and vibration of common rail direct injection (CRDI) diesel engines lead to the advent of piezo-actuated injectors. Compared with solenoid-actuated injectors, piezo-actuated injectors generate greater force and give faster response time, resulting in more accurate and faster injections. The accurate and fast response of an injector can offer an opportunity to control the combustion process and pollutant formation. In this study, the mathematical model of a piezo-actuated injector is developed. An estimator of the injection rate of the piezo-actuated injector is designed based on this model. The sliding mode theory is applied to the estimator design in order to overcome model uncertainties. The injector model and the estimator are verified by the injection experiments in an injector test bench. The simulation and the experimental results show that the proposed sliding mode observer can effectively estimate the injection timing and the injection rate of the piezo-actuated injector.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.12-18
• /
• 2004

Transient natures of diesel sprays are often characterized with spray visualization, since it is a non-intrusive and straightforward technique to be applied. However, as injection pressure is increased higher than a thousand bar in a modern direct injection diesel engine, very fine temporal and spatial resolutions in the spray visualization are required while sprays become optically denser. Discussed in this paper are macroscopic and microscopic spray visualization techniques and an example of image processing process for efficient and consistent measurement of spray parameters. The injection rate measurement method based on hydraulic pulse principle was suggested as a way of estimating injection velocity for transient diesel sprays. The spray visualization and injection rate measurement techniques were applied to analyze transient diesel sprays from a common-rail injection system and found to be practically effective.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.61-66
• /
• 2007

A CRDI diesel engine used to commercial vehicle was fueled with 20% biodiesel fuel(BDF 20) in excess of 150 hours. Engine dynamometer testing was completed at regularly scheduled intervals to monitor the engine performance and exhaust emissions. The engine performance and exhaust emissions were sampled at 1 hour interval for analysis, Also, BSEC with BDF 20 resulted in lower than with diesel fuel. Since the biodiesel fuel used in this study includes oxygen of about 11%, it could influence the combustion process strongly. So, BDF 20 resulted in lower emissions of carbon monoxide, carbon dioxide, and smoke emissions without special increase of oxides of nitrogen than diesel fuel. It was concluded that there was no unusual deterioration of the engine, or any unusual change in exhaust emissions from using the BDF 20.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.106-112
• /
• 2011

This study is to investigate the effect of an aromatic content in high cetane number (CN) fuels on exhaust emissions under low temperature diesel combustion, which expands the previous research about an aromatic content in low CN fuels. A 1.9L common rail direct injection diesel engine was run at 1500 rpm 2.6 bar BMEP with four fuel sets: an aromatic content of 20% (A20) or 45% (A45) with CN30, i.e. low CN fuels, and CN55, i.e. high CN fuels. Given experimental conditions, the trend of exhaust emissions in high CN fuels was inconsistent with that of low CN fuels which all produced nearly zero smoke but higher NOx for the high aromatic fuel (CN30-A45). For high CN fuels, however, the low aromatic fuel (CN55-A20) produced lower smoke than the high one (CN55-A45) while NOx was similar to each other. The cause of this discrepancy between high CN and low CN fuels is unclear whether it comes from that CN may be a dominant factor to govern exhaust emissions rather than an aromatic content or that the actual CN value of CN55-A45 is lower than CN55-A20. More decent fuel matrix should be prepared and further experiments are needed to confirm it.