• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.548-558
• /
• 2012

In this paper, a novel offset-based single-state pulse width modulation (PWM) method for achieving zero common-mode voltage (CMV) and reducing switching losses in multilevel inverters is presented. The specific active switching state of the zero common-mode (ZCM) voltage that approximates the reference voltage can be deduced from the switching state sequence of the reduced CMV phase disposition PWM (CMV PD PWM) method. From the reference leg voltages for the zero common-mode voltage, an N-to-2-level transformation defines a virtual two-level inverter and the corresponding nominal leg voltage references. The commutation process of the reduced CMV PD PWM method in a multilevel inverter and its outputs can be simply followed in a nominal switching time diagram for the virtual inverter. The characteristics of the reduced CMV PD PWM and the single-state PWM for zero common-mode voltage are analyzed in detail in this paper. The theoretical analysis of the proposed PWM method is verified by experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.488-493
• /
• 2014

This paper presents a carrier-based pulse-width modulation(PWM) method for reducing the common-mode voltage of a three-level four-leg converter. The idea of the proposed PWM method is intuitive and easy to be implemented in digital signal processor-based converter control systems. On the basis of the analysis of space-vector PWM(SVPWM) and sinusoidal PWM(SPWM) switching patterns, the fourth leg pole voltage of the three-phase converter called "f leg pole voltage" is manipulated to reduce the common-mode voltage. To synthesize f leg pole voltage for the suppression of the common-mode voltage, positive and negative pole voltage references of f leg are calculated. An offset voltage is also deduced to prevent the distortion of a, b, and c phase voltages. The feasibility of the proposed PWM method is verified by simulation and experimental results. The common-mode voltage of the proposed PWM method in peak-to-peak value is 33% in comparison with that of the conventional SVPWM method. The transition number of the common-mode voltage is also reduced to 25%.

• Journal of Power Electronics
• /
• v.14 no.2
• /
• pp.315-323
• /
• 2014

An optimized space vector pulse width modulation (SVPWM) method with common mode voltage elimination and neutral point potential balancing is proposed for an open-end winding induction motor. The motor is fed from both of the ends with two neutral point clamped (NPC) three-level inverters. In order to eliminate the common mode voltage of the motor ends and balance the neutral point potential of the DC link, only zero common mode voltage vectors are used and a balancing control factor is gained from calculation in the strategy. In order to improve the harmonic characteristics of the output voltages and currents, the balancing control factor is regulated properly and the theoretical analysis is provided. Simulation and experimental results show that by adopting the proposed method, the common mode voltage can be completely eliminated, the neutral point potential can be accurately balanced and the harmonic performance for the output voltages and currents can be effectively improved.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.4
• /
• pp.285-292
• /
• 2009

In this paper, when ac motors are driven by the diode rectifier/Z-source inverter system, the common-mode voltages of system are analyzed in details under both the shoot-through state and non-shoot-through state through equivalent circuits. Then a modified space vector modulation strategy is suggested for attenuating the negative common-mode voltage by eliminating the zero voltage vector, and also controlling the shoot-through time. Through the simulation studies with PSIM and experiments with 32-bit DSP, it is verified that the negative common-mode voltage can be reduced by more than 50%.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.923-930
• /
• 2018

Based on the application of an integrated dynamic brake (IDB) system that uses a PWM inverter fed-AC motor drive to operate the piston, a new active zero state PWM (AZSPWM) is proposed to improve the stability and reliability of the IDB system by suppressing the conducted electro-magnetic interference (EMI) noise under a wide range of load torque. The new AZSPWM reduces common-mode voltage (CMV) by one-third when compared to that of the conventional space vector PWM (CSVPWM). Although this method slightly increases the output current ripple by reducing the CMV, like the CSVPWM, it can be used within the full range of the load torque. Further, unlike other reduced common-mode voltage (RCMV) PWMs, it does not increase the switching power loss. A theoretical analysis is presented and experiments are performed to demonstrate the effectiveness of this method.

• Journal of electromagnetic engineering and science
• /
• v.15 no.2
• /
• pp.89-96
• /
• 2015

This paper describes the application of a passive noise cancellation method to a prototype inductor-inductor-capacitor (LLC) resonant converter by placing a compensation winding in a transformer to reduce common mode noise. The connection method for the compensation winding is investigated. A circuit analysis is implemented for the displacement currents between the primary and secondary windings in the transformer. The analyzed displacement currents are verified by performing a circuit simulation and a proper compensation winding connection that reduces common mode noise is found. The measurement results show that common mode noise is reduced effectively up to 20 dB in the 1 to 7 MHz frequency region for the prototype LLC resonant converter by using the proposed passive noise cancellation method.

• Nuclear Engineering and Technology
• /
• v.15 no.4
• /
• pp.229-235
• /
• 1983

Common Mode Failures (CMFs) have been a serious concern in the nuclear power plant. There is a broad category of the failure mechanisms that can cause common mode failures. This paper is a theoretical investigation of the CMFs on the unavailability of the redundant system. It is assumed that the total CMFs consist of the potential CMFs and the dependent human error CMFs. As the human error dependence is higher, the total CMFs are more effected by the dependent human error. If the human error dependence is lower, the system unavailability strongly depends on the potential CMFs, rather than the mechanical failure or the dependent human error. And it is shown that the total CMFs are dominant factor to the unavailability of the redundant system.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.794-796
• /
• 1993

This paper deals with the characteristic analysis of noise filter for the reduction of conduction noise, especially, common-mode noise. Attenuation in the system containing noise filter is analyzed and equivalent circuits for common- and differential- mode noise are derived. To clarify the effects by parasitic components of the inductor and capacitor, digital simulations using Design Center are carried out.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.504-508
• /
• 2004

An EMC analysis of a switched mode power supply (SMPS) have been usually using unbalance circuit topologies and the major factor of disturbance is parasitic capacitance. We have proposed a balanced switching converter circuit, which is an effective way to reduce the common mode conducted noise. In this paper presents the relationship between common mode current and radiated field.

• Journal of the Korea Society of Computer and Information
• /
• v.22 no.8
• /
• pp.63-72
• /
• 2017

In this paper, we propose a security architecture for HDLC-based T4 class common data link. The common data links are composed of point-to-point, multi-to-point, and point-to-multi mode. For multi-to-point mode, one node has a bundle of point-to-point links with different end-point on the other side of the links. Thus multi-to-point mode can be considered as a bundle of point-to-point mode. Point-to-multi mode is broadcasting link. For point-to-point mode we adopted robust security network scheme to establish a secure data link, and for multi-to-point mode we use broadcast encryption scheme based on ID-based cryptography to distribute encryption key for broadcasting message encryption. We also included MACsec technology for point-to-point data link security. Computational and communicational complexity analysis on the broadcast encryption have been done.