• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.5
• /
• pp.361-368
• /
• 2010

This paper presents high speed position controller using stepping motor. The proposed position controller has close loop and open loop mode. In the high speed region, torque angle which is controlled by PI controller and memory based look-up table, is used to keep the reference position. The memory based look-up table produces a torque angle according to motor speed, and the PI controller can compensate the torque angle error. So, the fast dynamic response can be expected in the same position error. The open loop control mode which is divided by 3-modes control the actual position in the low speed and small position error. Each open loop modes are designed to reduce position error and dynamic brake in the stop command. The proposed position control scheme is verified by the practical stepping motor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.7
• /
• pp.85-91
• /
• 2005

Supersonic jet fighter aircraft must have been guaranteed appropriate for controllability and stability in HAoA(High Angle of Attack) region. Limit value of aircraft enter the deep stall at HAoA is related to problem of aircraft configuration design. But, In order to guarantee the aircraft safety in HAoA, control law is designed using digital Fly-By-Wire flight control system in modern versions of supersonic jet fighter aircraft. Also, In order to recovery if aircraft enter the deep stall or spin, anti-spin control law and MPO(Manual Pitch Override) mode is designed. AoA limiter and MPO is designed in longitudinal axis and HAoA departure prevention logic, roll command limiter, rudder fader and anti-spin logic is designed in lateral-directional axis. In this paper, we introduce the T-50 HAoA flight control law and propose that aircraft stability and adequate of these control law from HAoA flight test.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2344-2346
• /
• 2002

A vacuum control system has been developed for using Ethernet Multi Serial Device Severs (EMSDS) for the Pohang Accelerator Laboratory (PAL) storage ring. There are 124 vacuum ion pumps at the storage ring. It was a very important problem to solve the problem how to control such a big number of vacuum pumps distributed around the ring. After discussions, we decided to develop a serial to ethernet interrace device sever that will be mounted in the control system rack. It has a 32-bits microprocessor embedded Linux, 12 ports RS485 (or RS232) slave interface. one channel 10/100BaseTx ethernet host port, one channel UART host port, and 16 Mbytes large memory buffer. These vacuum pumps are connected to Ion-Pump serial controllers, which chop the AC current so as to control the current in the pumps. The EMSDS connect either 100BaseTx or 10BaseT ethernet networks to asynchronous serial ports for communication with serial device. It can simultaneously control up to 12 ion-pump serial controllers. 12 EMSDS are connected to a personal computer (PC) through the network. The PC can automatically control the EMSDS by sending a set of commands through the TCP/IP network. Upon receiving a command from a PC running under Windows2000 through the network, the EMSDS communicate through the stave serial interrace ports to ion-pump controller. We added some software components on the top of EPICS (Experimental Physics and Industrial Control System) toolkit.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1164-1171
• /
• 2009

It has been 5 years since KTX high speed train was operated by KORAIL in Korea in April 2004. As for KTX train, France TGV was optimally renovated to make it, considering Korean geographical and environmental features. The research and development about KTX make it possible that train's exterior device design has the original design capability but, KTX train control & diagnosis design remains in the level of imitation. In order to analyze KTX train's diagnosis & control data, there are a collection method, using VME analysis device and method of analyzing control data structure and the operating and design capability about train control & diagnosis device should be secured. As the various high speed trains are operated in tracks, high speed train's safety driving and reduction of expense are necessary, by preparing in advance various train diagnosis & control which is indispensable to train operator. With the simplified train diagnosis & control design, Korean type high speed train's manufacture capability and operating capability should be improved and Korea's international status as a nation of operating high speed train should be established.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1095-1101
• /
• 2012

This paper presents a design of a BLDC servo motor control system for the auto process of assembly and supply using DSP(Digital Signal Processor) controller and IGBT driver. The assembly and supply auto processing system needs torque, speed, position control of servo motor for variable action. This paper implements those servo control with vector control and space vector PWM(Pulse Width Modulation) technique. As CPU of controller, TMS320F240 DSP was adopted because it has PWM waveform generator, A/D converter, SPI(Serial Peripheral Interface) port and many input/output port etc. This control system consists of 3-level hierarchy structure that main host PC manages three sub DSP system which transfer downward command and are monitoring the states of end servo controllers. Each sub DSP system operates eight BLDC servo controllers which control BLDC motor using DSP and IPM. Between host system and sub DSP communicate with RS-422, between main processor and controller communicate with SPI port.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.107-117
• /
• 2005

A distributed hardware-in-the-loop simulation (HILS) platform is developed for designing an automotive engine control system. The HILS equipment consists of a widely used PC and commercial-off-the-shelf (COTS) I/O boards instead of a powerful computing system and custom-made I/O boards. The distributed structure of the HILS system supplements the lack of computing power. These features make the HILS equipment more cost-effective and flexible. The HILS uses an automatic code generation extension, REAL-TIME WORKSHOP$^{ (RTW$^{) of MATLAB$^{ tool-chain and RT-LAB$^{, which enables distributed simulation as well as the detection and generation of digital event between simulation time steps. The mean value engine model, which is used in control design phase, is imported into this HILS. The engine model is supplemented with some I/O subsystems and I/O boards to interface actual input and output signals in real-time. The I/O subsystems are designed to imitate real sensor signals with high fidelity as well as to convert the raw data of the I/O boards to the appropriate forms for proper interfaces. A lot of attention is paid to the generation of a precise crank/ earn signal which has the problem of quantization in a conventional fixed time step simulation. The detection of injection! command signal which occurs between simulation time steps are also successfully compensated. In order to prove the feasibility of the proposed environment, a simple PI controller for an air-to-fuel ratio (AFR) control is used. The proposed HILS environment and I/O systems are shown to be an efficient tool to develop various control functions and to validate the software and hardware of the engine control system.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.4
• /
• pp.280-288
• /
• 2009

In this paper, we developed new time information recording module of VSI (VLBI Standard Interface) format by analyzing the Mark5B recorder control and operation software with 1Gbps speed, which is able to record the weak signal of space radio source, through the Korean VLBI Network (KVN). The control and operation software of high-speed recorder consists of 2 kinds of software, which is that it can operate RAID control board by controlling large capacity HDD drive and the network control and operation. Especially, core software in high-speed recorder is able to output the results after performing and analyzing the input command. Through the analysis of control and operation software, new time information recording module, which is needed to process the observed data for correlation, is developed. New developed time information recording module can record the time information together after checking the interrupt of 1PPS(Pulse Per Second) input signal when the observed data will be recorded. To verify the normal operation of the developed time information recording module, we performed the real observation test and confirmed the effectiveness of developed software through analyzing the recorded observation data.

• Parasites, Hosts and Diseases
• /
• v.52 no.2
• /
• pp.225-229
• /
• 2014

A total of 9,281 larval chigger mites were collected from small mammals captured at Hwaseong-gun, Gyeonggi-do (Province) (2,754 mites from 30 small mammals), Asan city, Chungcheongnam-do (3,358 mites from 48 mammals), and Jangseong-gun, Jeollanam-do (3,169 for 62 mammals) from April-November 2009 in the Republic of Korea (= Korea) and were identified to species. Leptotrombidium pallidum was the predominant species in Hwaseong (95.8%) and Asan (61.2%), while Leptotrombidium scutellare was the predominant species collected from Jangseong (80.1%). Overall, larval chigger mite indices decreased from April (27.3) to June (4.9), then increased in September (95.2) and to a high level in November (169.3). These data suggest that L. pallidum and L. scutellare are the primary vectors of scrub typhus throughout their range in Korea. While other species of larval chigger mites were also collected with some implications in the transmission of Orientia tsutsugamushi, they only accounted for 11.2% of all larval chigger mites collected from small mammals.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.23-30
• /
• 2016

Wake effects cause wind turbine generators (WTGs) within a wind power plant (WPP) to produce different levels of active power and subsequent reactive power capabilities. Further, the impedance between a WTG and the point of interconnection (POI)-which depends on the distance between them-impacts the WPP's reactive power injection capability at the POI. This paper proposes a voltage control scheme for a WPP based on the available reactive current of the doubly-fed induction generators (DFIGs) and its impacts on the POI to improve the reactive power injection capability of the WPP. In this paper, a design strategy for modifying the gain of DFIG controller is suggested and the comprehensive properties of these control gains are investigated. In the proposed scheme, the WPP controller, which operates in a voltage control mode, sends the command signal to the DFIGs based on the voltage difference at the POI. The DFIG controllers, which operate in a voltage control mode, employ a proportional controller with a limiter. The gain of the proportional controller is adjusted depending on the available reactive current of the DFIG and the series impedance between the DFIG and the POI. The performance of the proposed scheme is validated for various disturbances such as a reactive load connection and grid fault using an EMTP-RV simulator. Simulation results demonstrate that the proposed scheme promptly recovers the POI voltage by injecting more reactive power after a disturbance than the conventional scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.3
• /
• pp.292-300
• /
• 2011

Control systems in machinery equipment provide correction signals to motion units in order to reduce or cancel out the mismatches between sensor feedback signals and command or desired values. In this paper, we introduce a simulator for control characteristics of machinery equipment. The purpose of the simulator development is to provide mechanical system designers with the ability to estimate how much dynamic performance can be achieved from their design parameters and selected devices at the designing phase. The simulator has a database for commercial parts, so that the designers can choose appropriate components for servo controllers, motors, motor drives, and guide ways, etc. and then tune governing parameters such as controller gains and friction coefficients. The simulator simulates the closed-loop control system which is built and parameter-tuned by the designer and shows dynamic responses of the control system. The simulator treats the moving table as a 6 degrees-of-freedom rigid body and considers the motion guide blocks stiffness, damping and their locations as well as sensor locations. The simulator has been under development for one and a half years and has a few years to go before the public release. The primary achievements and features will be presented in this paper.