• 한국수소및신에너지학회논문집
• /
• 제29권3호
• /
• pp.280-291
• /
• 2018

Torrefaction is one of the methods to increase combustion calorific value and hydrophobicity of biomass. In this study, the effects of torrefaction on devolatilization, char reactivity and biomass structure were analyzed. Empty fruit bunch (EFB) and Kenaf biomass were used as fuels to be torrefied in the N2 environment at 200, 250 and $290^{\circ}C$. Devolatilization and char kinetics were analyzed by using TGA and biomass structure was investigated through petrography image. The reactivity showed different trends depending on the torrefaction temperature and biomass structure. The herbaceous biomass, Kenaf, was shown as high reactivity and thin wall structure. On the contrary, the woody biomass, EFB, had relatively low reactivity and thick wall structure.

• 한국연소학회지
• /
• 제14권3호
• /
• pp.16-23
• /
• 2009

It is strongly desired for coal-fired power plants to utilize not only low-rank coals with high moisture contents, but also lowering cost with diversifying fuel sources. In this study, combustion characteristics of low rank coal with high moisture, and standard pulverized coals are experimentally investigated using TGA (Thermogravimetric Analysis) and DTF (drop tube furnace). The coals tested are three kinds of coal with moisture content ranging from 8.32 to 26.82%. The results show that under the air combustion condition, the burn-out time at TGA rises as moisture content increases, and standard pulverized coal with 8.32% moisture content showed the lowest activation energy of 55.73 kJ/mol. In case of the high amount of moisture, the combustion efficiency decreases due to evaporation heat loss, and unburned carbon in ash produced at combustion process in DTF increased. Aslo, initial deformation temperature of slag attached in alumina tube of DTF decreased with lowering the crytallinity of anorthite and augite. To improve the combustion reactivity and efficiency, it is effective to upgrade through drying the high moisture coal to moisture level (less than 10%) of standard pulverized coal.

• 에너지공학
• /
• 제19권2호
• /
• pp.136-142
• /
• 2010

국내에 수입되어 사용되고 있는 발전용 석탄 2종에 대하여 기초적인 열중량분석기를 이용한 열특성 분석실험과 대용량 시험연소로를 이용한 연소시험을 수행하였다. 실험결과 고수분탄이 비록 착화 온도가 낮고 및 연소 구간이 짧아 초기 연소특성은 좋지만 비교탄에 비해 연소완료가 빨리 종결되지 못해 결과적으로는 연소 효율이 좋지 않았으며, 고수분탄의 활성화에너지는 고수분탄이 79 kJ/mol로서 비교탄의 53 kJ/mol에 비해 높은 특성을 보였다. 또한 시험연소로 시험과정에서 고수분탄의 화염 내 검은 색의 석탄분사체(Coal Jet) 형태가 비교탄에 비해 비교적 뚜렷이 관찰되어 연소속도가 다소 떨어지는 상호 연관성이 잘 설명되었고 연소후 미연분 발생량에서도 고수분탄이 다소 높게 나타났다. 그러나 고수분탄의 경우 낮은 유황분 함량으로 인해 연소 시 황산화물 배출량이 적어 고유황 함량의 석탄과의 혼합연소 시 유용하게 활용 될 수 있을 것으로 예상되었으며, 또한 회성분 분석결과 $Na_2O$와 $K_2O$ 등의 알카리비금속화합물 함량이 기존의 역청탄에 비해 매우 적고 회분자체의 함량도 매우 낮아 회분의 융착 정도가 높지 않게 나타났다.

• 한국산학기술학회논문지
• /
• 제22권6호
• /
• pp.75-82
• /
• 2021

디젤엔진의 열효율을 높이면서 NOx와 PM을 효과적으로 저감시키기 위해 HCCI(Homogeneous Charge Compression Ignition), PCCI(Premixed Charge Compression Ignition), RCCI(Reactivity Controlled Compression Ignition) 등의 저온연소(LTC: Low Temperature Combustion)전략이 개발되어 왔다. 본 연구에서는 저반응성 연료로는 가솔린을 사용하고 고반응성 연료로는 디젤을 사용하는 RCCI 엔진에서 고반응성 연료인 디젤연료의 분사 시기와 이단 분사비율이 성능 및 배출가스에 미치는 영향을 수치해석을 통하여 파악하고자 하였다. 이단 분사 시 첫 번째 분사시기가 너무 진각되면 연소가 느려지면서 연소온도가 낮아져 연소성능이 저하되고 HC, CO가 증가한다. 대략 -60°ATDC 의 분사시기가 연소성능, 배출가스 및 최대압력상승률을 고려하였을 때 가장 최적의 분사시기라고 판단된다. 이단 분사 시 두 번째 분사시기를 변경하였을 때 연소성능 및 배출가스, 최대압력상승률 등을 고려하면 대략 -30°ATDC 부근에서 최적인 것으로 판단된다. 이단 분사 시 분사량 비율은 첫 번째 분사량을 60% 정도로 하였을 때 최적의 결과를 얻었다. 마지막으로 단일 분사보다는 이단 분사한 경우 연소성능 및 배출가스 부분에서 더 효과적인 것으로 판단된다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.181-186
• /
• 2004

Catalytic combustion is one of the suitable methods which is applicable to micro heat source due to high energy density and no flame quenching. And hydrogen can be oxidized at room temperature with platinum catalyst. So hydrogen-fueled micro catalytic combustor with platinum catalyst can be good and easy-handling heat source for another micro devices. In this work we focused on general catalytic combustion characteristics of hydrogen-air premixed gas in 10mm scale catalytic combustor for the further application to micro scale. Platinum was coated on dense ceramic monolith which can be installed in simple-structured catalytic combustor. We investigated the effect of flow rate, heat loss and platinum percentage in catalyst-coated monolith on catalytic combustion performance by temperature distribution in the combustor. By those results we confirmed catalytic reactivity and estimated reaction area. And we simulated micro scale catalytic reaction by sliced monolith. The results of this work will be important design factors for micro scale catalytic combustor.

• 한국연소학회지
• /
• 제15권1호
• /
• pp.22-29
• /
• 2010

In this study, carbon conversion was measured using an electronic mass balance. In a lab scale furnace, each coal sample was pyrolyzed in a nitrogen environment and became coal char, which was then gasified with steam under isothermal conditions. The reactivity of coal char was investigated at various temperatures and steam concentrations. The VRM(volume reaction model), SCM(shrinking core model), and RPM(random pore model) were used to interpret experimental data. For each model the activation energy(Ea), pre-exponential factor (A), and reaction order(n) of the coal char-steam reaction were determined by applying the Arrhenius equation into the data obtained with thermo-gravimetric analysis(TGA). According to this study, it was found that experimental data agreed better with the VRM and SCM for 1,000 and $1,100^{\circ}C$, and the RPM for 1,200 and $1,300^{\circ}C$. The reactivity of chars increased with the increase of gasification temperature. The structure parameter(${\psi}$) of the surface area for the RPM was obtained.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.128-130
• /
• 2017

수중추진을 위한 고체추진제로 알루미늄 분말의 수반응성을 높이기 위하여 $NaBH_4$를 첨가하였다. 알루미늄 분말은 $NaBH_4$의 첨가량에 따라 다른 연소특성을 보였다. $NaBH_4$를 첨가하였을 때 끓는점보다 훨씬 낮은 온도에서도 물과 반응하여 연소되었다. 본 연구에서 $NaBH_4$는 Al 분말과 증기 반응을 촉진시키는 효과적인 첨가제임을 확인하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.33-40
• /
• 2004

Combustion of coke/anthracite in an iron ore sintering bed is characterized quantitatively by introducing newly defined parameters related to propagation and thickness of combustion zone and maximum temperature. The parameters are obtained by sintering pot experiment and I-D, unsteady numerical model which treats solid material as multiple solid phases. Experiments and calculations are performed for various major operating parameters: air inlet velocity, different type of fuels which have different reactivity and diameter of the solid fuel. Effects of the operating parameters on the productivity and quality of the sintering process are investigated and evaluated quantitatively and the results show that optimized air supply rate and diameter of anthracite for replacement of coke can be obtained. This approach can be applied to other kinds of combustors for characterization of the combustion in the solid fuel beds.

• 융복합기술연구소 논문집
• /
• 제9권1호
• /
• pp.13-19
• /
• 2019

The purpose of this study is to suggest a new method to determine a combustion phase (start of combustion and end of combustion) using a combustion pressure data. Unlike previous research method that used heat release amount, the difference between the combustion pressure measured in the combustion chamber and the motoring pressure was used to determine the combustion phase. This research was conducted using a single-cylinder diesel engine with a compression ratio of 17.7. The test was conducted under various injection timing. The newly proposed method showed high accuracy in combustion mode with early injection, as well as the conventional combustion mode. It is expected that this method will be used to study new combustion strategies such as HCCI (homogeneous charge compression ignition) and RCCI (reactivity controlled compression ignition) that are applying early injection strategies as well as existing combustion modes.

• 한국연소학회지
• /
• 제16권1호
• /
• pp.22-29
• /
• 2011

This paper focuses on the combustion characteristics of blended coals with bituminous and sub-bituminous coals under air and oxy-fuel combustion conditions. The effects of oxygen concentration and blending ratio on the combustion characteristics were experimentally investigated using a thermogravimetric analyser (TGA). Characteristic temperatures including ignition, burnout temperature and activation energy were determined from TG and DTG combustion profiles. As oxygen concentration increased and the presence of sub-bituminous coal, characteristic temperatures and activation energy decreased. The ignitability, reactivity and kinetics have all been greatly improved under oxy-fuel combustion conditions. Based on this, co-firing with bituminous and sub-bituminous coals under oxy-fuel combustion conditions may be suggested as an alternative method to the fuel flexibility and cost-effective power production with carbon capture and sequestration.