• Journal of the Korean Society of Combustion
• /
• v.12 no.4
• /
• pp.22-30
• /
• 2007

The NOx emission characteristics were studied in an oscillating combustion burner equipped with a specially designed proportioning valve. The effects of various parameters on the NOx emission which are important in oscillating combustion were investigated. Also, the effects of coincident application of flue gas recirculation(FGR) were evaluated. The results show that oscillating combustion is an efficient tool for reducing NOx in the burner. Up to 53% of NOx reduction could be acquired in low frequency and small duty ratio conditions. The coincident application of FGR further reduced the NOx emission up to 74%. Thus, this study assured that oscillating combustion technology with FGR could be a fascinating method for NOx reduction in industrial burners.

• Journal of the Korean Society of Combustion
• /
• v.11 no.3
• /
• pp.18-25
• /
• 2006

The present studying is aimed to establish the relationship between flame chemiluminescence$(OH^*,\;CH^*,\;C_2^*)$ intensities and combustion conditions such as $NO_x$ emission characteristics. Measurements are made for $OH^*,\;CH^*,\;C_2^*$ radicals in gas & light oil diffusion flames. At turbulent nonpremixed combustion mode, the equivalence ratio is varied. The optical emissions were measured by photomultiplier(PMT) using optical band pass filter and spectrometer system. The experimental results showed that the ratio of radicals and $NO_x$ emission characteristics have exponential correlations and equivalence ratio characteristics have linear correlations at this experimental conditions.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.57 no.3
• /
• pp.256-263
• /
• 2021

In this study, blending oils of diesel oil and butanol were used as fuel oil for diesel engine to measure combustion pressure, fuel consumption, air ratio and exhaust gas emission due to various operating conditions such as engine revolution and torque. Using these data, the results of analyzing the engine performance, combustion characteristics and exhaust emission characteristics such as NOx (nitrogen oxides), CO₂ (carbon dioxide), CO (carbon monoxide) and soot were as follows. The fuel conversion efficiency at each load was highest when driven in the engine revolution determined by a fixed pitch propeller law. Except 30% butanol blending oil, fuel conversion efficiency of the other fuel oils increased as the load increased. Compared to diesel oil, using 10% and 20% butanol blending oil as fuel oil was advantageous in terms of thermal efficiency, but it did not have a significant impact on the reduction of exhaust gas emissions. On the other hand, future research is needed on the results of the 20% butanol blending oil showing lower or similar levels of smoke concentration and carbon monoxide emission rate other than those types of diesel oil.

• Journal of the Korean Society of Combustion
• /
• v.16 no.3
• /
• pp.52-58
• /
• 2011

The purpose of this paper is to investigate the effect of equivalence ratio on the combustion and emission characteristics of a compression ignition engine fueled with biodiesel. In this research, a single-cylinder direct injection engine with 373.3 cc of displacement volume was tested on DC dynamometer. In order to investigate the effect of biodiesel equivalence ratio on combustion characteristics, the experiments were conducted at various equivalence ratios and injection pressures of 40~120 MPa. For investigating engine performance, lambda meter was connected and equivalence ratios was varied from 0.6 to 1.0. In addition, the exhaust emissions such as oxides of nitrogen($NO_X$), hydrocarbon(HC) and carbon monoxide(CO) were measured by exhaust gas analyzer under the various air/fuel ratios. The experimental results show that maximum IMEP was measured at the 0.8 of equivalence ratio. Furthermore, $NO_X$ emission was rapidly decreased as the increase of equivalence ratio. However soot emission was significantly increased according to the increase of equivalence ratio.

• Journal of the Korean Society of Combustion
• /
• v.16 no.3
• /
• pp.33-40
• /
• 2011

Combustion experiments were conducted at three different fuels ($CH_4$, $C_2H_4$ and $C_3H_8$) to investigate the effects of combustor pressure (30 ~ -30 kPa) on combustion charateristics and reaction zone structure. Regardless of the fuels, emission index of CO (EICO) increased with decreasing combustor pressure, and EICO of $C_2H_4$ was mostly affected by changing combustor pressure at subatmospheric pressure. In order to observe reaction zone, $OH^*$, $CH^*$ and ${C_2}^*$ chemiluminescence intensity were measured. The sequence of the chemiluminescence intensity peak position was affected by chemical characteristics of fuels rather than changing combustor pressure. The emission zone thickness of $C_2H_4$ and $C_3H_8$, defined by the full width at half maximum (FWHM) of $CH^*$ intensity profile, were increased with decreasing combustor pressure. however, the thickness of $C_2H_4$ exhibited the opposite tendency due to the characteristics of the fuel as the bond structure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.358-364
• /
• 2016

The combustion and exhaust emission characteristics in a spark ignition (SI) engine with various test fuels (bioethanol - gasoline blends) and air-fuel ratio were investigated in this research. To investigate the influence of the excess air ratio and ethanol blends on the combustion characteristics such as the cylinder pressure, rate of heat release (ROHR), and fuel consumption rate were analyzed. In addition, the reduction effects of exhaust emissions such as carbon monoxide (CO), unburned hydrocarbon (HC), and oxides of nitrogen (NOx) were compared with those of neat gasoline fuel under the various excess-air ratios. The results showed that the peak combustion pressures and the ROHR of bioethanol fuel cases were slightly higher than those of gasoline fuel at all test ranges and fuel ratio. As compared with gasoline fuel (G100) at each given excess air ratio, BSFC of bio-ethanol was increased. The CO, HC, NOx emissions of bio-ethanol blends were lower than those of gasoline fuel under overall experimental conditions.

• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2175-2180
• /
• 2008

Oxy-fuel combustion has been gaining its significance as a means of migrating the green house effects. Some experimental measurements were conducted to investigate the characteristics of oxy-fuel combustion and to aid a fundamental design of a lab-scale oxy-fuel combustor with a coaxial burner. CO emission was measured along the combustor centerline while combustion of methane and oxygen diluted by CO2 took place. Substitution of CO2 with N2 indicates a possibility that some CO is formed by dissociation of CO2. Some parametric tests were also performed to see the mixing effects of reactant gases on CO emission by changing the gas injection velocity at the burner nozzles with various heat loads. The overall results indicate that CO emission was reduced when the reactants are injected at higher velocities of similar magnitude.

• Journal of ILASS-Korea
• /
• v.17 no.3
• /
• pp.152-157
• /
• 2012

This investigation decribes the effect of the combustion and emission characteristics of HCNG engine according to the high purity hydrogen contents. The HCNG fuel was made by the mixture with a high purity hydrogen ($H_2$) and a natural gas. The test vehicle was applied to the bi-fuel (Gasoline and CNG) system and this system was modified from the fuel supply and fuel tank. In addition, the three premixed HCNG fuels with mixed rate of 10, 20 and 30% of hydrogen were used to maintain the safety. In order to analyze the combustion characteristics of HCNG and CNG, the fuel was injected in the combustor with constant volume. The exhaust emission from light duty vehicle with bi-fuel system was analyzed by a chassis dynamometer and emission analyzer. From these results, the reduction rate of NOx emission increased in the HCNG fuel and emission amount of THC and CO shows a similar level with CNG fuel. This study can be utilized the basic data for the development of a new business plans related with HCNG engines.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.77-84
• /
• 2002

For the purpose of obtaining a fundamental data which is needed to develope the port injection type charged LPLi engine system, we manufactured intake port injection system of liquid charging LPG and modified heavy duty single cylinder LPLi engine from heavy duty diesel engine. Engine output and emission characteristics were analyzed under variable air/fuel ratio and charging pressure. Since LPG is consisted of propane and butane, we investigated combustion characteristics using this two kinds of fuel. From the result of charging engine performance test, engine torque increase about 30% ∼ 40% with 0.3bar charging pressure. In low speed condition, as charging pressure increase, combustion stability improve ill lean bum condition, but, in high speed condition, combustion stability make worse in lean bum condition. We know that engine output decreased rapidly from the condition of air excess ratio 1.3. In addition, we measured emission characteristics under the lean bum and charging condition. From this experiment, we found that CO emission is out of the question in the range from stiochiometric to lean burn and charging condition, but charging pressure has influence on HC emission.