• 에너지공학
• /
• 제18권1호
• /
• pp.31-36
• /
• 2009

환경친화적인 자동차 제조 방법에는 몇 가지 방법이 있다. 하이브리드 전기자동차는 가장 현실적인 방법일 것이다. 하이브리드 전기자동차는 내연기관과 전기장치의 두 가지 동력을 사용한다. 하이브리드 전기자동차는 연료소비와 배기가스 저감을 위해서 개발되었다. 저자들은 하이브리 전기자동차의 주요 동력원으로 디젤 기관을 선택했다. 테스트는 도심버스주행모드와 고속도로주행모드가 사용되었다. 본 연구는 직렬하이브리드 전기자동차, 병렬하이브리드 전기자동차, 플러그인 직렬 전기자동차와 플러그인 병렬 전기자동차에 따른 중형디젤 하이브리드 자동차의 연료경제성과 배기가스의 시뮬레이션의 결과를 제시하고 있다.

• Advances in environmental research
• /
• 제4권3호
• /
• pp.143-153
• /
• 2015

The ventilation system is a key device to ensure both healthful indoor air quality (IAQ) and thermal comfort in buildings. The ventilation system should make the IAQ meet the standards such as ASHRAE 62. This study deals with a new approach to modeling the ventilation and IAQ requirement in residential buildings. In that approach, Elite software is used to calculate the air supply volume, and CONTAM model as a multi-zone and contaminant dispersal model is employed to estimate the contaminants' concentrations. Amongst various contaminants existing in the residential buildings, two main contaminates of carbon dioxide ($CO_2$) and carbon monoxide (CO) were considered. CO and $CO_2$ are generated mainly from combustion sources such as gas cooking and heating oven. In addition to the mentioned sources, $CO_2$ is generated from occupants' respirations. To show how that approach works, a sample house with the area of $80m^2$ located in Tehran was considered as an illustrative case study. The results showed that $CO_2$ concentration in the winter was higher than the acceptable level. Therefore, the air change rate (ACH) of 4.2 was required to lower the $CO_2$ concentration below the air quality threshold in the living room, and in the bedrooms, the rate of ventilation volume should be 11.2 ACH.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2001년도 학술발표회 발표논문집
• /
• pp.281-285
• /
• 2001

This study was carried out to improve the performance of heat recovery device attached to exhaust gas flue connected to combustion chamber of greenhouse heating system. Three different units were prepared for the comparison of heat recovery performance; AB-type(control unit) is exactly the same with the typical one fabricated for previous study of analyzing heat recovery performance in greenhouse heating system, other two types(C-type and D-type) modified from the control unit are different in the aspects of airflow direction(U-turn airflow) and pipe arrangement. The results are summarized as follows; 1. In the case of Type-AB, when considering the initial cost and current electricity fee required for system operation, it is expected that one or two years at most would be enough to return the whole cost invested. 2. Type-C and Type-D, basically different with Type-AB in the aspect of airflow pattern, are not sensitive to the change of blower capacity with higher than $25\;m^{3}/min$. Therefore, heat recovery performance was not improved so significantly with the increment of blower capacity. This is assumed to be that air flow resistance in high air capacity reduces the heat exchange rate as well. Never the less, compared with control unit, resultant heat recovery rate in Type-C and Type-D were improved by about 5% and 13%, respectively. 3. Desirable blower capacity for these heat recovery units experimented are expected to be about $25\;m^{3}/min$, and at the proper blower capacity, U-turn airflow units showed better heat recovery performance than control unit. But, without regard to the type of heat recovery unit, it is recommended that comprehensive consideration of system's physical factors such as pipe arrangement density, unit pipe length and pipe thickness, etc., are required for the optimization of heat recovery system in the aspects of not only energy conservation but economic system design.

• 대한임베디드공학회논문지
• /
• 제12권4호
• /
• pp.247-258
• /
• 2017

Since 2016 when the regulations related to vehicle structure and device modification were drastically revised, the car tuning market has been growing rapidly. Particularly, many drivers are showing interest in changing the interior and exterior according to their preference, or improving the specifications of their cars by changing the engine and powertrain, among others. Also, as the initial engine settings such as horse power and torque of the vehicle are made for stable driving of the vehicle, it is possible to change the engine performance, via Engine Control Unit (ECU) mapping, to the driver's preference. However, traditionally, ECU mapping could be only performed by professional car engineers and the settings were also decided by them. Therefore, this study proposed a system that collects data related to the driver's driving habits for a certain period and sends them to a cloud server in order to analyze them and recommend ECU mapping values. The traditional mapping method only aimed to improve the car's performance and, therefore, if the changes were not compatible with the driver's driving habits, could cause problems such as incomplete combustion or low fuel efficiency. However, the proposed system allows drivers to set legally permitted ECU mapping based on analysis of their driving habits, and, therefore, different drivers can set it differently according to the vehicle specifications and driving habits. As a result, the system can optimize the car performance by improving output, fuel efficiency, etc. within the range that is legally permitted.

• 한국산학기술학회논문지
• /
• 제15권3호
• /
• pp.1229-1235
• /
• 2014

LPG차량의 공기 흡입 시스템에서 먼지 입자의 대부분은 공기 청정기를 통해 제거되지만, 아주 작은 입자는 제거되지 않고 흡기계통에 축적되게 된다. 이 축적된 카본은 공회전 속도 제어와 센서신호 그리고 배출가스에 영향을 주게 된다. 또한 엔진 채터링 현상이나 자동변속기의 변속시점 불량등을 야기시킨다. 이 연구는 세척액을 사용하여 흡기계통을 세척하는 것에 관한 것이다. 워밍업된 챠량에서 흡입호스를 제거하고 세척액을 사용하여 가속시에 세척액을 흡입장치에 분사시켜 흡기계통을 세척하는 것이다. 세척액을 사용하여 스로틀 바디, ISC, 서지탱크, 흡입매니폴드, 흡기밸브, 연소실까지 세척함으로서 다음과 같은 실험결과를 얻을 수 있다. 스로틀 밸브가 정확하게 작동되어 TPS의 센서 신호 전압이 개선되었으며, 차량이 정지하는 경우 ISC 시스템은 공회전 속도 제어를 원활하게 작동하였다. 또한 일산화탄소는 약 0.15 %, 탄화수소는 약 20~100PPM으로 각각 감소되어 배기가스가 현저하게 개선되었다.

• 한국분말재료학회지
• /
• 제24권1호
• /
• pp.46-52
• /
• 2017

Fecralloy coating layer with large surface area is suitable for use as a filter media for efficient removal of hot gaseous pollutants exhausted from combustion processes. For uniform preparation of a Fecralloy coating layer with large surface area and strong adhesion to substrate, electrospray coating and thermal treatment processes are experimentally optimized in this study. A nano-colloidal solution with 0.05 wt% Fecralloy nanoparticles is successfully prepared. Optimized electrospraying conditions are experimentally discovered to prepare a uniform coating layer of Fecralloy nano-colloidal solution on a substrate. Drying the electrospray coated Fecralloy nano-colloidal solution layer at $120^{\circ}C$ and subsequent heating at $600^{\circ}C$ are the best post-treatment for enhancing the adhesion force and surface roughness of the Fecralloy coating layer on a substrate. An electrospray coating system, consisting of several multi-groove nozzles, is also experimentally confirmed as a reasonable device for uniform coating of Fecralloy nano-colloid on a large area substrate.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.54-62
• /
• 2007

The knock characteristics in an engine were investigated under homogeneous charge compression ignition (HCCI) operation. Liquefied petroleum gas (LPG)and gasoline were used as fuels and injected at the intake port using port fuel injection equipment. Di-methyl ether (DME) was used as an ignition promoter and was injected directly into the cylinder near compression top dead center (TDC). A commercial variable valve timing device was used to control the volumetric efficiency and the amount of internal residual gas. Different intake valve timingsand fuel injection amounts were tested to verify the knock characteristics of the HCCI engine. The ringing intensity (RI) was used to define the intensity of knock according to the operating conditions. The RI of the LPG HCCI engine was lower than that of the gasoline HCCI engine at every experimental condition. The indicated mean effective pressure (IMEP) dropped when the RI was over 0.5 MW/m2and the maximum combustion pressure was over 6.5MPa. There was no significant relationship between RI and fuel type. The RI can be predicted by the crank angle degree (CAD) at 50 CA. Carbon monoxide (CO) and hydrocarbon (HC) emissions were minimized at high RI conditions. The shortest burn duration under low RI was effective in achieving low HC and CO emissions.

• 한국화재소방학회논문지
• /
• 제19권3호
• /
• pp.13-19
• /
• 2005

본 논문에서는 금속염 첨가제를 함유한 미분무수의 소화성능을 연구하고자 아세트산 나트륨을 함유한 단일 액적의 증발속도를 측정하였으며, small-scale 챔버내에서의 헵탄 pool fire에 대한 소화실험을 실시하여, 화염의 온도를 분석함으로써 첨가제에 의한 미분무수 소화특성을 분석하였다. 순수물과 수용액의 증발특성을 비교한 결과 핵비등 영역에서 온도가 높을수록 용해된 첨가제의 석출 및 표면장력의 변화 등 물리적 영향으로 순수물에 비해 수용액의 증발속도가 현저히 느리게 나타났다. 소화실험 결과, 저압에서는 물 액적이 화염의 플림을 뚫지 못하기 때문에 소화는 이루어지지 않았고 단순히 화염의 크기를 작아지게 하였다. 중압에서는 첨가제를 넣었을 경우 액적의 운동량 증가에 따른 물리적 소화효과와 첨가제의 화학적 소화효과가 상승작용을 하여 화염을 억제하였고, 고압에서는 미분무수 시스템의 주요 소화 메커니즘 이외에도 blowing효과에 의해서 화염이 소화되는 것을 관찰할 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제25권4호
• /
• pp.405-418
• /
• 2014

Fuel cells are suitable for a power plant of a unmanned aerial vehicle (UAV) as it is not only environmentally friendly and quiet but also more efficient than an internal combustion engine. A fuel cell hybrid UAV has better performance in endurance than a fuel cell only or battery only UAV. One of the key purposes of making fuel cell hybrid UAVs is having long endurance and now maximum 26 hours of flight is possible. Because optimal design and control methods for fuel cell hybrid UAVs are absolutely needed for their long endurance we have to check the methods. The aircraft made by using application-integrated design method has less BOP mass and better performances. The optimal design and control methods are generally based on computer simulations or Hardware-In-The-Loop simulations by using dynamic models for their design and control. The Hardware-In-The-Loop simulation (HILS) is to use a hardware device like a fuel cell stack as well as a simulation program and it allows for making optimally designed applications. This paper introduce efficient methods of design, control and evaluation for the fuel cell hybrid UAVs.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.146-153
• /
• 2013

CNG buses has contributed to improve air quality in cities. But it is difficult to meet the next emission regulations such as EURO-VI without the help of additional post-processing device. Hydorgen has higher flame speed and lower combustion temperature that make it thermal efficiency increase with leaner operation. Using hydrogen natural gas blend (HCNG) fuel is promising technology which can reduce $NO_x$ and $CO_2$ emissions for a natural gas vehicle. However, fuel flow rate of HCNG should be increased since hydrogen's energy density per volume is much smaller than natural gas. In the present study, the characteristics of fuel supply system and its applicability were evaluated in a heavy duty natural gas engine. The results showed that the potential of fuel pressure regulator and fuel metering valve had enough capacity with HCNG. Employed mixer did not affect the distribution characteristics of mixture.