• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.242-247
• /
• 2003

An experimental study presents characteristics of combustion in a combustion chamber by port deactivation valve for economy and emissions standards. In order to use combustion properties data it is necessary to build some data base, which use cylinder pressure sensor, etc. Port deactivation valve has been developed to satisfy requirement of achieving sufficient swirl generation to improve the combustion. A feasibility and necessity of combustion pressure based cylinder spark timing control has been examined. So, this was obtained the Coefficient of Variation(COV) and the mass-burned(MFB). The characteristics of pressure ratio fraction is similar to that of mass-burned fraction. Using the results of the test, the effects of the combustion chamber can be improved combustion stability by port deactivation.

• 대한기계학회논문집
• /
• 제16권3호
• /
• pp.569-577
• /
• 1992

본 연구에서는 주연소실쪽의 오리피스 근방에서 점화를 하는 부실붙이 연소실 에서 부실의 크기, 오리피스 크기를 변수로 하여 화염분출이 연소에 미치는 영향을 파 악하였다. 또한 이들의 결과를 부실쪽에서 점화하는 경우와 비교하여 주연소실쪽 점 화방식의 화염분출효과를 평가하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.149-152
• /
• 2008

30톤급 액체로켓엔진 실물형 연소기의 형상에 따른 연소특성속도에 대한 연구를 수행하였다. 본 연구에서 연소기의 형상은 연소기 헤드와 분리가 가능한 내열재 및 채널 냉각형 연소실(${\varepsilon}$=3.2), 그리고 일체형인 팽창비가 각각 3.5와 12인 재생냉각형 연소기이다. 연소압력은 약 53${\sim}$60 bar 그리고 추진제 유량은 약 89 kg/s이고, 적용된 분사기는 리세스수가 1.0인 동축 와류형이다. 설계점 연소시험에서 팽창비가 12인 일체형 재생냉각 방식의 연소기가 가장 큰 연소특성속도를 보였는데 이는 추진제인 케로신이 분무되기 전 챔버 냉각으로 인한 온도 상승에 따른 엔탈피의 증가 및 연소압력의 증가에 기인한 것이다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.1084-1087
• /
• 2017

액체로켓에서 엔진의 시동은 산화제와 연료를 연소기에 매우 짧은 시간의 차를 두고 주입하여야 하며, 이때 주입시간의 간격, 점화기 작동 지연 등은 방대한 량의 추진제 혼합물에 에너지를 인가함으로서 대형 폭발로 이어질 수 있는 상황이 된다. 그러므로 각 추진제의 천이특성과 연소기 또는 가스발생기의 유입 시점을 측정하는 것은 매우 중요하며, 상대적으로 느린 응답 특성을 갖는 정압으로는 유입 시점을 관측하기에는 어려움이 많으므로 추진제 유로를 따라 동압을 측정하여 보다 정확한 유입시점을 찾을 수 있었다.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.45-53
• /
• 2004

An experimental study was carried out to obtain the fundamental data about the effects of radicals induced injection on premixture combustion. A constant volume combustor divided to the sub-chamber and the main chamber was used. The volume of the sub-chamber is set up to occupy less than 1.5％ of that of whole combustion chamber. Radial twelve narrow passage holes are arranged between the main chamber and the sub-chamber. The products including radicals generated by spark ignition in the sub-chamber will derive the simultaneous multi-point ignition in the main chamber. While the equivalence ratio of pre-mixture in the main chamber and the sub-chamber is uniform. We have examined the effects of the sub-chamber volume, the diameter of passage hole, and the equivalence ratio on the combustion characteristics by means of burning pressure measurement and flame visualization. In the case of radical ignition method(RI), the overall turning time including the ignition delay became very short and the maximum burning pressure was slightly increased in comparison with those of the conventional spark ignition method(SI), that is, single chamber combustion without the sub-chamber. The combustible lean limit by RI method is extended to more ER=0.25 than that by SI method. Therefore the decrease of every emission including NOx and the improvement of fuel consumption is anticipated due to lean burn.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.75-82
• /
• 2004

The allowable exhaust standard has been intensified as a part of the countermeasure to decrease air pollution in the world. As the cars with an alternative fuel starts to get into the spotlight, the cars with low emission has been introduced and exhaust gas regulation forced in this country. These days, LPG vehicles, which infrastructure of fuel was already built up, and CNG vehicles are recognized for alternative fuel cars in this country. In this study, the constant volume combustion chamber was manufactured and used for experiments to obtain the ignition characteristics of LPG fuel and the optimal ignition energy. The experiment measured the combustion characteristics, in regard to the change of combustion variable, and the change of ignition energy. During the combustion of fuel, the maximum temperature inside the combustion chamber is higher when the initial pressure is higher. The burning velocity also seems to have the same characteristic as the temperature. However, the heat flux did not change much with the theoretical correct mixture but the various initial temperature of the combustion chamber. The heat flux got faster and ignition energy bigger as the dwell time of the ignition system expanded. When the dwell time get longer, the ignition energy also increased then fixed. The ignition energy increased as the initial pressure inside the combustion chamber higher. The heat flux got faster as the dwell time expanded.

• 대한기계학회논문집
• /
• 제10권5호
• /
• pp.635-644
• /
• 1986

A Compuressible turbulent boundary layer effect of the high temperature, accelerating gas flow through the De-Laval nozzle on combustion chamber pressure is numerically investigated. For this purpose, the coupled momentum integral equation and energy integral equation are solved by the Bartz method, and 1/7 power law for both the turbulent boundary layer velocity distribution and temperature distribution is assumed. As far as the boundary layer thicknesses are concerned, we can obtain reasonable solutions even if relatively simple approximations to the skin friction coefficient and stanton number have been used. The effects of nozzle wall cooling and/or mass flow rate on the boundary layer thicknesses and the combustion chamber pressure are studied. Specifically, negative displacement thickness is appeared as the ratio of the nozzle wall temperature to the stagnation temperature of the free stream decreases, and, consequently, it makes the combustion chamber pressure low.

• International Journal of Automotive Technology
• /
• 제7권4호
• /
• pp.391-397
• /
• 2006

The soot yield has been studied by a premixed propane-oxygen-inert gas combustion in a specially designed disk-type constant-volume combustion chamber to investigate the effect of pressure, temperature and turbulence on soot formation. Premixtures are simultaneously ignited by eight spark plugs located on the circumference of chamber at 45 degrees intervals in order to observe the soot formation under high temperature and high pressure. The eight converged flames compress the end gases to a high pressure. The laser schlieren and direct flame photographs with observation area of 10 mm in diameter are taken to examine the behaviors of flame front and gas flow in laminar and turbulent combustion. The soot volume fraction in the chamber center during the final stage of combustion at the highest pressure is measured by the in-situ laser extinction technique and simultaneously the corresponding burnt gas temperature by the two-color pyrometry method. The changes of pressure and temperature during soot formation are controlled by varying the initial charging pressure and the volume fraction of inert gas compositions, respectively. It is found that the soot yield increases with dropping the temperature and raising the pressure at a constant equivalence ratio, and the soot yield in turbulent combustion decreases as compared with that in laminar combustion because the burnt gas temperature increases with the drop of heat loss for laminar combustion.

• 한국추진공학회지
• /
• 제13권6호
• /
• pp.8-16
• /
• 2009

고압 축소형 연소기의 개발에 관하여 기술하였다. 헤드부와 챔버부가 분리형인 연소기와 일체형 재생냉각 방식의 연소기 등 총 4기의 연소기가 개발되었다. 축소형 연소기의 연소 압력은 70 bar이고, 추진제 유량은 5.1~9.1 kg/s이다. 연소성능의 향상을 위해 추진제 유량, 분사기의 recess 수 등을 변화시켰고, 이를 연소시험을 통해 확인하였다. 또한 실물형 연소기에 적용할 재생냉각 채널과 막냉각의 설계 및 제작 기술을 본 축소형 연소기에 적용, 검증하였다.