• 한국식품영양과학회지
• /
• 제41권11호
• /
• pp.1632-1638
• /
• 2012

치콘의 미생물학적 안전성을 확보하기 위해 50 ppm 이산화염소수와 5 kJ/$m^2$ UV-C 및 2 kGy 전자빔 조사 병합처리에 따른 저장 중 미생물 수 및 품질 변화를 $4{\pm}1^{\circ}C$에서 11일 동안 저장하면서 측정하였다. 이산화염소수와 UV-C 병합처리 후 치콘의 총 호기성 세균 수는 대조구와 비교하여 1.49~2.92 log CFU/g, 효모 및 곰팡이는 1.63~1.78 log CFU/g의 감소를 보였다. 반면에, 이산화염소수와 2 kGy 전자빔 병합처리구의 경우 총 호기성 세균은 저장기간 동안 검출되지 않았으며, 효모 및 곰팡이 역시 11일 간의 저장기간 동안 나타나지 않았다. 이산화염소수와 전자빔의 병합처리는 대조구와 비교하여 치콘의 저장 중 Hunter 색도 값에 부정적 영향을 미치지 않았다. 관능검사에 있어서도 저장기간 동안 대조구와 비교 시 유의적인 차이가 없는 것으로 나타났다. 따라서 본 연구결과, 이산화염소수와 전자빔 조사의 병합처리가 치콘의 저장 중 오염될 수 있는 위해미생물의 감소와 외관적 품질유지에 효과적인 살균처리 기술이라고 판단된다.

• Applied Microscopy
• /
• 제45권4호
• /
• pp.189-194
• /
• 2015

Backside Ar ion milling technique for the preparation of cross-sectional transmission electron microscopy (TEM) specimens, and backside-ion milling combined with focused ion beam (FIB) operation for electron holography were introduced in this paper. The backside Ar ion milling technique offers advantages in preparing cross-sectional specimens having thin, smooth and uniform surfaces with low surface damages. The back-side ion milling combined with the FIB technique could be used to observe the two-dimensional p-n junction profiles in semiconductors with the sample quality sufficient for an electron holography study. These techniques have useful applications for accurate TEM analysis of the microstructure of materials or electronic devices such as arrayed hole patterns, three-dimensional integrated circuits, and also relatively thick layers (> $1{\mu}m$).

• 농업과학연구
• /
• 제39권3호
• /
• pp.341-347
• /
• 2012

The objective of this study was to investigate the combined effect of electron beam irradiation (EB) and onion peel extracts and selected flavorings on microbiological and sensory quality of pork jerky. Total aerobic bacteria were detected in the range of $3.87{\pm}0.30{\sim}4.60{\pm}0.12$ log CFU/g in all samples. Addition of both onion peel extract and flavoring showed the decrease of total aerobic bacterial count in pork jerky. No viable cells were observed after EB at 4 kGy. Sensory evaluation indicated that the EB-treated pork jerky with 0.5% barbecue flavoring did not show any difference in overall acceptability compared with the control. Therefore, combined use of EB with onion peel extracts and barbecue flavoring may enhance the safety of pork jerky with proper sensory quality.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 추계총회 및 연구발표회 초록집
• /
• pp.179.2-179
• /
• 2003

• 한국압력기기공학회 논문집
• /
• 제18권2호
• /
• pp.61-68
• /
• 2022

Accurate evaluation of residual stress is important for stress corrosion cracking assessment. In this paper, electron beam welding experiment is simulated via finite element analysis and the sensitivity of the parameters related to the combined heat source model is investigated. Predicted residual stresses arecompared with measured residual stresses. It is found that the welding efficiency affects the size of the tensile residual stress area and the magnitude of maximum longitudinal residual stress. It is also found that the parameter related to the ratio of energy distributed to the two-dimensional heat source has little effect on the size of tthe tensile residual stress area, but affects the size of the longitudinal residual stress in the center of the weld.

• Journal of Radiation Protection and Research
• /
• 제42권1호
• /
• pp.63-68
• /
• 2017

Background: The combined effect of the low energy electron (LEE) irradiation and $Cu^{2+}$ ion on DNA damage was investigated. Materials and Methods: Lyophilized pBR322 plasmid DNA films with various concentrations (1-15 mM) of $Cu^{2+}$ ion were independently irradiated by monochromatic LEEs with 5 eV. The types of DNA damage, single strand break (SSB) and double strand break (DSB), were separated and quantified by gel electrophoresis. Results and Discussion: Without electron irradiation, DNA damage was slightly increased with increasing Cu ion concentration via Fenton reaction. LEE-induced DNA damage, with no Cu ion, was only 6.6% via dissociative electron attachment (DEA) process. However, DNA damage was significantly increased through the combined effect of LEE-irradiation and Cu ion, except around 9 mM Cu ion. The possible pathways of DNA damage for each of these different cases were suggested. Conclusion: The combined effect of LEE-irradiation and Cu ion is likely to cause increasing dissociation after elevated transient negative ion state, resulting in the enhanced DNA damage. For the decrease of DNA damage at around 9-mM Cu ion, it is assumed to be related to the structural stabilization due to DNA inter- and intra-crosslinks via Cu ion.

• Radiation Oncology Journal
• /
• 제1권1호
• /
• pp.29-36
• /
• 1983

The treatment of tumors along curved surfaces with stationary electron beams using cone collimation may lead to non-uniform dose distributions due to a varying air gap between the cone surface and patient. For large tumors, more than one port may have to be used in irradiation of the chest wall, often leading to regions of high or low dose at the junction of the adjacent ports. Electron-beam arc therapy may elimination many of these fixed port problems. When treating breast tumors with electrons, the energy of the internal mammary port is usually higher than that of the chest wall port. Bolus is used to increase the skin dose or limit the range of the electrons. We invertiaged the effect of various arc beam parameters in the isodose distributions, and combined into a single arc port for adjacent fixed ports of different electron beam eneries. The higher fixed port energy would be used as the arc beam energy while the beam penetration in the lower energy region would be controlled by a proper thickness of bolus. We obtained the results of following: 1. It is more uniform dose distribution of electron to use rotation than stationary irradiation. 2. Increasing isocenter depth on arc irradiation, increased depth of maximum dose, reduction in surface dose and an increasing penetration of the linear portion of the curve. 3. The deeper penetration of the depth dose curve and higher X-ray background for the smaller field sized. 4. If the isocenter depth increase, the field effect is small. 5. The decreasing arc beam penetration with decreasing isocenter depth and the isocenter depth effect appears at a greater depth as the energy increases. 6. The addition of bolus produces a shift in the penetration that is the same for all depths leaving the shape of the curves unchanged. 7. Lead strips 5 mm thick were placed at both ends of the arc to produce a rapid dose drop-off.

• Applied Microscopy
• /
• 제41권3호
• /
• pp.147-154
• /
• 2011

후방산란전자(BSE)는 입사전자빔이 시료와 충돌하면서 발생한다. BSE 이미징은 시료의 화학적 특성을 구분할 수 있는 조성대비를 제공한다. 집속이온빔장치(FIB)는 전계방사형 주사전자현미경(FESEM)과 결합할 수 있으므로 이중빔 체계(FIB-FESEM)가 구현된다. 갈륨(Ga) 이온빔으로 10~100 nm 두께로 시료를 절삭할 수 있으므로 FIB-FESEM은 플라스틱으로 포매된 블록의 면을 z축 고해상도를 유지하며 연속적으로 이미징할 수 있다. BSE이미지의 대비를 반전시키면 투과전자현미경의 이미지와 유사하다. 연속블록면 이미징의 또 다른 방안으로써 특수한 초박절편기가 FESEM 내부에 장착된 것이 $3View^{(R)}$로 상용화되어 있다. 이로써 플라스틱으로 포매된 시료의 내부 구조를 넓은 면적을 연속적으로 이미징 할 수 있으므로 3차원 재구성도 용이하게 된다. 이러한 FESEM에 기반한 두 가지 방식은 복잡한 생물계의 총체적인 이해를 위하여 세포 및 세포 수준 이하의 구조물 간의 공간적 연관성을 규명하는 데 활용될 수 있다.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.51-61
• /
• 2012

The new alkali pulping process combined with electron beam treatment was applied to utilize hemp bast tissues as a new valuable fibrous resource. Hemp bast tissues have some chemical properties with high lignin contents and holocellulose not to be defiberized by alkali pulping only, compared with the bast tissue of paper mulberry. To make up for the weakness of traditional alkali pulping process, electron beams were directly irradiated into the swelled bast tissue of hemp in NaOH solution and distilled water, and then facilitated the defiberization of hemp bast tissues. The papermaking from hemp bast fibers manufactured by the combination pulping process showed good apparent density, formation structure and air permeability, and had some mechanical properties with lower tensile, tear, burst strength and folding endurance. It is finally concluded that the combination pulping process with electron beam treatment could be suggested a new alternative for non-woody fibers.

• 한국레이저가공학회지
• /
• 제18권4호
• /
• pp.1-5
• /
• 2015

For continuous laser micro patterning on three-dimensional free form surface, innovative laser system is developed. The two axis galvanometer is combined with the dynamic focusing unit to increase optical distance. Also, it is synchronized with the 3 axis mechanical system. To determine laser machining sequence, laser CAM system is developed. It can make possible of 3D surface micro patterning under $25{\mu}m$ pattern width. The uniformity of pattern width is about 2.8% and it is validated that focal plane is well conserved by the dynamic focusing unit. Velocity and positional information of 1 axis is stage is fed to the scanner control board by the encoder signal and it makes possible real time synchronization. With this system, possible patterning volume is enlarged from $40{\times}40mm^2$ to $40{\times}120{\times}30mm^3$.