• Journal of the Korean GEO-environmental Society
• /
• v.15 no.2
• /
• pp.67-74
• /
• 2014

Recently, the number of road construction is increasing by industrial development. According to this industrial tendency, the number of traffic accidents are consistently increasing due to increasing number of vehicle on the road. This is mainly because traffic accidents are occurred by various parameter such as negligence of driver, vehicle defects, state of unstable road, natural environment etc. Lane department of vehicles from guardrail is occurring frequently. This type of accident is caused by vehicle performance improvement and shape of vehicle, weak guardrail installation and maintenance. Guardrail has the purpose on prevention such as prevention of traffic accident and prevention of deviating out of road, minimizing damage of driver and vehicle by collision as well as entry into the road through guardrail. Stability evaluation test of guardrail verifies the behavior of guardrail through the crash of truck. At this time, the crash condition has 100 km/h of velocity and $15^{\circ}$ of impact angle. In the case of ground condition, filling slope condition has relatively high bearing capacity of infinite ground towards the test. Guardrail is generally installed on road of shoulder in fill slope in korea. It is possible for stability problem to deteriorate ground bearing capacity in Guardrail in fill slope. The existed study towards stability of guardrail has been carried out in the infinite ground. However, the study on the behavior of fill slope with guardrail is not performed by vehicle collision. Therefore, In this study, the numerical analysis using LS-DYNA was executed for verification on behavior of fill slope with guardrail through vehicle collision. This numerical analysis was carried out with change of embedded depth on installed guardrail post in shoulder of fill slope by vehicle collision and 8 tonf truck crash providing at NCAN (National Crash Analysis Center). As the result, displacement and stress on fill slope are decreased in accordance with the increase of embedded depth of guardrail post. Ground bearing capacity is deteriorated at depth of 450 mm form shoulder of road on fill slope.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.3
• /
• pp.607-616
• /
• 2015

The demand for cars has been so steadily increasing based on the economic growth that the number of registered cars reached 18,870,000 as of the end of December, 2012. Due to this, the demand for the parking lots also rises continuously. Because of the limited ground space, the buildings ever becoming larger, and the trend of underground parking spaces, recent parking spaces are generally constructed underground. Accordingly, the parking lot ramps slope is limited to less than 17% by relevant laws to ensure the driver safety. However, when a driver enters a parking lot ramps whose slope is slightly steep, he frequently experiences his car body colliding with ramp brackets and often sees the scratches on ramp floor. Thus, this study is intended to prevent any damage to a structure and to contribute to ensuring the riding comfort and safety of drivers and passengers by presenting the details of proper vertical curve to prevent the collision of vehicles with ramp brackets through a vertical analysis of the first and last parts of a parking lot ramps. Because it is necessary to decide the appropriate and suitable vertical slope of a parking lot ramps, this study first identified the problems through site inspection, targeting the parking lot ramps of large buildings frequently that are used by many random people. Next, the possibility of mutual collision was assessed through a theoretical analysis of the first and last parts of a parking lot ramps. Lastly, the vertical curve of a parking ramp was analyzed to estimate its details, which was presented in this study. In conclusion, if the vertical curve presented through this study is used, it will help prevent any damage to the cars and structures, ensure the riding comfort and safety of the drivers, and further reestablish the criteria for vertical installation of a parking lot ramps.

• Journal of Auto-vehicle Safety Association
• /
• v.10 no.4
• /
• pp.7-12
• /
• 2018

Injury mechanisms of lower extremity injuries in motor vehicle accidents are focused on fractures, sprains, and contusions. The purpose of this study is to evaluate the analysis of lower extremity injury mechanism in occupant motor vehicle accident by using Hospital Information System (HIS) and reconstruction program, based on the materials related to motor vehicle accidents. Among patients who visited the emergency department of Wonju Severance Christian Hospital due to motor vehicle accidents from August 2012 to February 2014, we collected data on patients with agreement for taking the damaged vehicle's photos. After obtaining the verbal consent from the patient, we asked about the cause of the accident, information on vehicle involved in the accident, and the location of car repair shop. The photos of the damaged vehicle were taken on the basis of front, rear, left side and right side. Damage to the vehicle was presented using the CDC code by analytical study of photo-images of the damaged vehicle, and a trauma score was used for medical examination of the severity of the patient's injury. Among the 1,699 patients due to motor vehicle crashes, 88 (5.2%) received a diagnosis of lower extremity fracture and 141 (8.3%) were the severe who had ISS over 15. Nevertheless during 19 months for research, it was difficult to build up in-depth database about motor vehicle crashes. It has a limitation on collecting data because not only the system for constructing database about motor vehicle crash is not organized but also the process for demanding materials is not available due to prevention of personal information. For accurate analysis of the relationship between occupant injury and vehicle damage in motor vehicle crashes, build-up of an in-depth database through carrying out various policies for motor vehicle crashes is necessary for sure.

• The Korean Journal of Air & Space Law and Policy
• /
• v.1
• /
• pp.163-191
• /
• 1989

The accident of the midair collision, passengers' falling or goods' dropping occurs or supersonic aircraft make a sonic boom during their conveying passengers or goods to the destination. The accident in transmit damages the their parties on the surface or their properties. In these cases, the third parties who were harmed to their lives or properties have the right to claim damages against the air carrier who caused them. These matters have become one of the important things since aircraft conveyed passengers and goods. Therefore, it is a great concern to settle these matters by law. But the Safety of the present aircraft has been much increased and the aircraft have become larger in size. Its flight altitude became higher than before. So the relationship of the aircraft to the third parties is much different from that of the earlier aircraft. The air transport is now indispensable to our life. It is not so easy to control these matters. In the early part of 20th century, when the third parties suffered the damage, many European countries made laws on the basis of the principle of liability without fault. But each country had a variety of its own law, and different kinds of difficulties have been brought about. Accordingly, the Rome Convention on Surface Damage (1933, 1952, 1978) has been made and revised. In spite of being revised, it contains many problems, and is not carried into effect world-wide. On the other hand, there are no regulations about the compensation of the third parties damaged in Korean existing laws. In case the damage is brought about to them, it is obviously true that the settlement of the liability of compensation for damage should be made by the general principle on the tort in domestic laws. At this point, it is urgent that we make a special law though the domestic legislation as a preliminary measure before we sign the international convention to save third damaged. It is desirable that we should, for the responsibility of the air carriage for the demage of the third parties on the surface, bring in the theory of the absolute liability in view of the legislation of many conutries. As the aircraft fly in the sky, their flight always contains some danger. It is very difficult to prove the fault, and the operator should suffer the principle of liability without fault or the similiar one. In case the liability without fault will be imposed upon the operator for the damage of the third parties, it is necessary to bring in the liability protection system for the protection and up upbringing of the air carriage. The Burden of danger of the air carriage will be reduced by introducing the system. A domestic legislation measure should be necessarily taken as soon as possible as a legal security measure on these matters.

• Journal of the Korean Institute of Gas
• /
• v.16 no.6
• /
• pp.102-106
• /
• 2012

The purpose of this paper is to study the failure cases in relation to system of Air Bag in vehicle happened in the field. In the first example, it was separated the soldering parts connected the wire pin between air bag module and clock spring of air bag. Whenever the pin shake by the car's vibration, the driver verified the malfunction phenomenon appeared air bag warning lamp on instrument panel in front of driver's seat. in car inside room. The second example, it verified the warning lamp lighting phenomenon of air bag by produced the circuit plate non-contacting of single an element in air bag electronic control unit. The third example, it verified the light of air bag warning indicator lamp by separated with soldering parts connecting inner pin and resistance terminal of seat belt pretensioner using passenger seat. The fourth example, when the passenger car crash a back of truck, the former bumper get jammed under the latter as the roof height of car low less than that. Therefore, the impact of Car's collision verified that don't transfer with body frame of vehicle because of no attachment impact sensor in it.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.276-281
• /
• 2014

Necessities of a traffic means work a car in the modern society human to an usability of a life is enjoying. On the other hand, the damage by traffic accident increment the human quotient worked as we were in proportion to the vehicle which increased. Passing an examination moves necessarily on an obstacle to suddenly appear at the fronts if a car travels and the vehicles which stopped suddenly. Dynamic passing an examination about an obstacle turn on Vehicle Emergency Lamp to by hand when is unhurried, and can turn off, but to appear urgently dynamic passing an examination in time human is instinctive, but cannot inform an emergency to a back vehicle, and a rear-end collision occurs. A car we synthesize a speed of a vehicle, and this unit analyzes as we use GPS, and to drive runs Vehicle Emergency Lamp to automatic in the situations that shall turn on emergencies etc. If a speed of a vehicle continuously slows down in too high-speed driving or low-speed driving, or we are stopped, Vehicle Emergency Lamp is always turned on. It was built if we rise again as clearing itself from risk, and a speed of a vehicle judges, and we turn off Vehicle Emergency Lamp to automatic. It runs till rear-end collision sensor operates, and by hand reset does Vehicle Emergency Lamp a driving vehicle collides from behind to a back vehicle or when a driving vehicle was overthrown. It is shortened very much to the chain rear-end collision traffic accident that is a traffic accident of large size if we use this unit. And we did authentication through the experiment which a driver was helpful to unnecessary operation and a relaxed safe driving during drivings.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.199-209
• /
• 2011

In the study of traffic safety, the analysis on factors affecting crash severity and the understanding about their relationship is important to be planning and execute to improve safety of road and traffic facilities. The purpose of this study is to develop a hierarchical binomial logistic model to identify the significant factors affecting fatal injuries and vehicle damages of traffic crashes on freeway. Two models on death and total vehicle damage are developed. The hierarchical structure of response variable is composed of two level, crash-occupant and crash-vehicle. As a result, we have gotten the crash-level random effect from these hierarchical structure as well as the fixed effect of covariates, namely odds ratio. The crash on the main line and in-out section have greater damage than other facilities. Injuries and vehicle damages are severe in case of traffic violations, centerline invasion and speeding. Also, collision crash and fire occurrence is more severe damaged than other crash types. The surrounding environment of surface conditions by climate and visibility conditions by day and night is a significant factor on crash occurrence. On the orher hand, the geometric condition of road isn't.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.843-849
• /
• 2010

This paper presents definition of symmetry of a ship section where three symmetries are proposed: material, geometric, and load symmetries. Precise terminologies of centroid, moment plane, and neutral axis plane are also defined. It is suggested that force vector equilibrium as well as force equilibrium are necessary condition to determine new position of neutral axis due to translational and rotational mobility. It is also stated that new reference datum of ENMP(elastic neutral moment plane), PNMP(fully plastic moment plane), ENAP(elastic neutral axis plane), and INAP(inelastic neutral moment plane) are required to define asymmetric section properties such as second moment of area, elastic section modulus, yield moment, fully plastic moment, and ultimate moment. Since collision-induced damage and flooding-induced biaxial bending moment produce typical asymmetry of section, the section properties are calculated for a typical VLCC. Geometry asymmetry is determined from ABS and DNV rules and two moment planes of 0/30 degs are assumed for load asymmetry. It is proved that the property reduction ratios directly calculated from second moment of area are usually larger than area reduction ratio. Reduction ratio of ultimate moment capacity shows almost linearly proportional to area reduction ratio. Mobility of elastic and inelastic neutral axis planes is visually provided.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.4
• /
• pp.303-309
• /
• 2016

As commercialization of the Arctic sea route and resource developments are regularized, demands for ice-breaking tankers, LNG carriers, and offshore plants are expected to increase. In addition, the existing ice-breaking cargo ships navigating in the ice-covered waters are worn out. Hence, the construction of new ships is likely to be undertaken for both current and long-term applications. The design of ships navigating in ice-covered waters demands conservative methods and strict development standards owing to the extreme cold and collision tendencies with ice floes and/or icebergs. ISO 19906 recently stated that a fatigue limit should be defined when designing Arctic offshore structures such that the ice-induced fatigue becomes one of the important design drivers. Thus, establishing systematic measures to mitigate ice-induced fatigue problems in ice-breaking ships are important from the viewpoint of having a competitive advantage. In this paper, the issues relating to ice-induced fatigue problems, based on data and published literature, are examined to describe the criticality of ice-induced fatigue. Potential fatigue damage possibilities are investigated using data measured in the Arctic Ocean (2013) and using the Korean icebreaker, ARAON.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.23 no.6
• /
• pp.289-299
• /
• 2019

The tendency to use a probabilistic design method rather than a deterministic design method for the design of nuclear power plants (NPPs) will increase because their safety should be considered and strictly controlled in relation to various causes of damage. The distance between a seismically isolated NPP structure and a moat wall is called the clearance to stop. The clearance to stop is obtained from the 90th percentile displacement response of a seismically isolated NPP subject to a beyond design basis earthquake (BDBE) in the probabilistic design method. The purpose of this study is to analyze the effects of heating and buckling effects on the 90th percentile displacement response of a lead-rubber bearing (LRB) subject to a BDBE. The analysis results show that considering the heating and buckling effects to estimate the clearance to stop is conservative in the evaluation of the 90th percentile displacement response. If these two effects are not taken into account in the calculation of the clearance to stop, the underestimation of the clearance to stop causes unexpected damage because of an increase in the collision probability between the moat wall and the seismically isolated NPP.