• Journal of ILASS-Korea
• /
• v.21 no.2
• /
• pp.78-87
• /
• 2016

This study experimentally investigated the effects of droplet temperature on the heat transfer characteristics during collision of a single droplet on a heated wall above the Leidenfrost temperature. Experiments were performed by varying temperature from 40 to $100^{\circ}C$ while the collision velocity and wall temperature were maintained constant at 0.7 m/s at $500^{\circ}C$, respectively. Evolution of temperature distribution at the droplet-wall interface as well as collision dynamics of the droplet were simultaneously recorded using synchronized high-speed video and infrared cameras. The local heat flux distribution at the collision surface was deduced using the measured temperature distribution data. Various physical parameters, including residence time, local heat flux distribution, heat transfer rate, heat transfer effectiveness and vapor film thickness, were measured from the visualization data. The results showed that increase in droplet temperature reduces the residence time and increases the vapor film thickness. This ultimately results in reduction in the total heat transfer by conduction through the vapor film during droplet-wall collision.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.589-596
• /
• 2012

In this paper, the reactive dynamics properties of the reactions Ba + $C_6H_5Br$ and Ba + m-$C_6H_4CH_3Br$ were studied by means of the quasi-classical trajectory method based on the London-Eyring-Polanyi-Sato potential energy surfaces. The vibrational distributions, reaction cross sections, rotational alignments of the products BaBr all were obtained. The peak values of the vibrational distributions are located at $\nu$ = 0 for the reactions Ba + $C_6H_5Br$ and Ba + m-$C_6H_4CH_3Br$ when the collision energies are 1.09 and 1.10 eV, respectively. The reaction cross sections increase with the increasing collision energy, which changes from 0.6 to 1.5 eV. The product rotational alignments deviate from -0.5 and firstly increase and then decrease while the collision energy is increasing, just like that of Heavy+Light-Light system.

• Journal of Auto-vehicle Safety Association
• /
• v.5 no.2
• /
• pp.11-16
• /
• 2013

This paper presents a unified control algorithm of independent braking and steering for collision avoidance. The desired motion of the vehicle in the yaw plane is determined using the probabilistic risk assessment method based on target state estimation. For the purpose of coordinating the independent braking and steering, a non-linear vehicle model has been developed, which describes the vehicle dynamics in the yaw plane in both linear and extended non-linear ranges of handling. A control allocation algorithm determines the control inputs that minimize the difference between the desired and actual vehicle motions, while satisfying all actuator constraints. The performance of the proposed control algorithm has been investigated via computer simulations conducted using the vehicle dynamics software CARSIM and Matlab/Simulink.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.70-77
• /
• 2015

The purpose of this study was to provide fundamental data for an anchor collision simulation of an FCM (flexible concrete mattress). Numerical material models (elastic-perfectly plastic model, Drucker-Prager model, and RHT concrete model) were compared. ANSYS Explicit Dynamics was used for collision analyses. An FE model was used for the anchor, FCM, andreinforcement bars. The results showed that the behavior of the FCM was verydifferent that those ofthe material models. In particular, the effect of the pressure dependent strength was most noticeable among the properties of concrete.

• The Journal of Korea Robotics Society
• /
• v.13 no.3
• /
• pp.157-163
• /
• 2018

This paper deals with the development and application of control algorithms for series elastic relief robots for rescue operations in harsh environment like disasters or battlefield. The joint controller applied in this paper has a cascade structure combining inner loop for torque control and outer loop for position control. The torque loop contains feedforward and feedback controller and disturbance observer for independent, decentralized joint control. The effect of the elastic component and motor dynamics are treated as the nonlinear disturbance and compensated with the disturbance observer of torque controller. For the collision detection, Band Designed Disturbance Observer is configured to recognize/respond to external disturbance robustly in the continuously changing environment. The controller is applied to a 7-dof series elastic manipulator to evaluate the torque tracking and collision detection/response performance.

• 연구논문집
• /
• s.32
• /
• pp.103-111
• /
• 2002

In this study, the crashworthiness of KHST has been evaluated by analysing a nonlinear spring/bar-damper-mass model of 1-dimensional collision dynamics. The numerical results show that KHST can easily absorb kinetic energy at lower impact force and acceleration in heavy collisions, when compared with KTX. Also, in a Light collision like a traint-to-train accident at lower speed under 8 kph, the carbody and components of KHST can be protected without any damage except the energy absorbing tube to be replaced easily. However, KTX may be much damaged in the light collision because there is no energy absorbing tube. In conclusion, the crashworthy performance of KHST has been much improved than that of KTX, although there are something to be improved for a better crashworthy performance

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.139-150
• /
• 2000

Although a number of neck injuries are generated, the data which quantify the kinematic response of the human head and cervical spine in low-speed rear-end automobile collisions is very limited. On this problem, just few in vitro experimental research or some experimental research using dummy on neck injury by rear-end collision was conducted, thus systematic research is requested on full scale injury mechanism. An occupant model for the response of the occupant subject to rear-end collision using commercial dynamics package DADS was developed. Developed model shows more close agreement with the experimental data compared with the MADYMO simulation results for the cases of ${\delta}V=16$ kph in sled test. For the case of ${\delta}V=8$ kph and 33.5 kph with production seat, model also shows its reliable response compared with experimental results using Hybrid III and Hybird III with RID.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.283-288
• /
• 2001

We have investigated aluminum cluster deposition using a classical molecular dynamics simulations. We studied the variations of the cluster momentum and the impulse force during collisions, and found that the close-packed cluster impact has some of properties of the single particle collision and the linear atomic chain collisions. We also simulated the series of energetic cluster deposition with energy Per atom. When energy Per atom in cluster has some eV rather than very low, the intermixing occurred easily in growth film and we can obtain a good film without subsequent annealing process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.2
• /
• pp.1-11
• /
• 1994

The most commonplace of collisions that directly affect people is that of vehicles. Safety studies have noted a correlation between vehicle occupant injury severity and velocity changes. Methods for estimating collision velocity changes are discussed here. This topic is part of what is referred to as accident reconstruction. Only planar collisions are considered. When a vehicle collides with another, impact dynamics with friction should be considered. This paper presents a general analysis methodology of impact. must dynamics incorporating friction. The presence of friction between sliding contacts during the impact makes the problem difficult since the events such as reverse sliding or sticking, which may occur at different times throughout the impact, must be determined. This paper uses the results of RICSAC experiments for verifying the developed methodology. The analysis and experimental results agree well.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.291-298
• /
• 2003

Recently, load/unload(L/UL) process is applied to a computer information storage device due to its advantages such as lower power consumption, larger data zone, simpler fabrication of disk for no bumped parking zone, and rarer contact between the slider and media. An analysis of the transient motion for the slider is very important to design an air bearing surface (ABS) of the slider to secure the stable performance of the system. During the L/UL process, however, there are several issues occurred such as contact or collision between slider and media. Sometimes this will cause the system failure. In this study, the dynamics of the slider during the loading process are investigated through a numerical simulation using FEM analysis and experiment.