• 한국강구조학회 논문집
• /
• 제27권3호
• /
• pp.281-288
• /
• 2015

댐퍼를 비롯한 대부분의 내진성능 향상 부재는 골조를 구성하는 주요구조부재가 소성상태에 진입한 다음 나타나는 층 강성 저하에 대한 대처가 없어 대지진 시 건물의 층 파괴를 방지하지 못할 가능성이 높다. 이에 본 논문은 건물의 주요부재가 탄성항복한 뒤에도 건물의 층 강성을 일정기간 유지시킬 수 있는 고강도강 내진성능 향상부재를 제안한다. 본 논문에서는 다음과 같은 사실을 알 수 있다. (1) 골조의 소성화 항복 후 저감된 수평내력을 보강하는 탄성 부재를 제안방식으로 설계 시 기존 면적을 방해하지 않는 작은 단면으로 최대 층간변형각 0.02rad 까지 내력 저감 보강 가능 (2) 제안 내진성능 향상부재의 최저 적용으로도 설계 레벨을 상회하는 거대 지진에서 과다변형집중방지에 상당한 효과를 발휘하는 것을 확인.

• 한국해양공학회지
• /
• 제34권2호
• /
• pp.110-119
• /
• 2020

Explosions and fires on offshore drilling units and process plants, which cause loss of life and environmental damage, have been studied extensively. However, research on drilling units increased only after the 2010 Deepwater Horizon accident in the Gulf of Mexico. A major reason for explosions and fires on a drilling unit is blowout, which is caused by a failure to control the high temperatures and pressures upstream of the offshore underwater well. The area susceptible to explosion and fire due to blowout is the drill floor, which supports the main drilling system. Structural instability and collapse of the drill floor can threaten the structural integrity of the entire unit. This study simulates the behavior of fire subsequent to blowout and assesses the thermal load. A heat transfer structure analysis of the drill floor was carried out using the assessed thermal load, and the risk was noted. In order to maintain the structural integrity of the drill floor, passive fire protection of certain areas was recommended.

• Earthquakes and Structures
• /
• 제15권4호
• /
• pp.395-402
• /
• 2018

Floor location of adjacent buildings may be different in terms of height elevation, and thus, the slab may hit on the columns of adjacent insufficiently separated buildings during severe ground motions. Such impacts, often referred to as mid-column pounding, can be catastrophic. Substantial pounding damage or even total collapse of structures was often observed in large amount of adjacent low rise buildings. The research on the mid-column pounding between low rise buildings is in urgency need. In present study, the responses of two adjacent low rise buildings with unequal heights and different dynamic properties have been analyzed. Parametric studies have also been conducted to assess the influence of story height difference, gap distance and input direction of ground motion on the effect of structural pounding response. Another emphasis of this study is to analyze the near-fault effect, which is important for the structures located in the near-fault area. The analysis results show that collisions exhibit significant influence on the local shear force response of the column suffering impact. Because of asymmetric configuration of systems, the structural seismic behavior is distinct by varying the incident directions of the ground motions. Results also show that near-fault earthquakes induced ground motions can cause more significant effect on the pounding responses.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 춘계 학술논문 발표대회
• /
• pp.7-10
• /
• 2008

As the land price in the downtown area increases, buildings are becoming bigger, deeper and higher. Consequently, the importance of underground construction has increased. Although construction engineers make every effort to complete underground construction without any problem, construction failures like landslides and the collapse of a retaining wall occur because of the uncertainty of the soil conditions as well as the unexpected risks of excavation work. In order to prevent potential excavation accidents, it is essential to understand the causes and impacts of such accidents. However, there are only a few examples of construction failures, which show the economic impact on accidents during excavation because of the sensibility of the information. This paper presents two cases of excavation accidents, which were investigated by construction insurance company. The compensation for the accidents paid by the insurance company was compared with the estimated costs calculated based on the estimation method for excavation accidents proposed by our previous study. The comparison results showed that the estimate calculated by our method was much less than the actual compensation because the estimate solely focused on the construction costs whereas the compensation included other external factors.

• 화약ㆍ발파
• /
• 제26권1호
• /
• pp.1-5
• /
• 2008

본 연구에서는 대규모 원통형 구조물의 사전 취약화에 따른 구조적 안전성을 확보하기 위하여 파쇄 각도에 대한 구조물의 붕괴 영향을 검토하였다. 파쇄 각도에 대한 영향을 검토하기 위해 구조적으로 동일한 원통형 구조물을 ELS 프로그램을 이용하여 모형화하였다. 파쇄 형태 및 높이에 대한 변수는 고정시키고, 파쇄 각도를 변화시키면서 시간에 따른 각 방향별 변위를 분석하였다. 원통형 구조물의 시뮬레이션 결과, 사전 취약화에 대한 파쇄 범위는 40%이하 이어야 한다는 것을 확인할 수 있었다.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.171-180
• /
• 2005

Bending performances of aluminum square tube beams reinforced by aluminum plates under three point bending loads have been evaluated using experimental tests combined with theoretical and finite element analyses. A finite element simulation for the three-point bending test was performed. Basic properties of aluminum materials used for initial input data of the finite element simulation were obtained from the true stress-true strain curves of specimens which had been extracted from the Al tube beams. True stresses were determined from applied loads and cross-sectional area records of a tensile specimen with a rectangular cross-section by real-time photographing, and true strains were obtained from in-situ local elongation measurements of the specimen gage portion by the multi-point scanning laser extensometer. Six kinds of aluminum tube beam specimens adhered by aluminum plates were employed fur the bending test. The bending deformation behaviors up to the maximum load described by the numerical simulation were in good agreement with experimental ones. After passing the maximum load, reinforcing plate was debonded from the aluminum tube beam. An aluminum tube beam strengthened by aluminum plate on the upper web showed an excellent bending capability.

• Coupled systems mechanics
• /
• 제7권2호
• /
• pp.177-195
• /
• 2018

Reinforced concrete buildings in a seismically active area can be designed as DCM (medium ductility) or DCH (high ductility) class according to the regulations of Eurocode 8. In this paper, two RC buildings, one with a wall structural system and the other with a frame system, previously designed for DCM and DCH ductility, were analysed by using incremental dynamic analysis in order to study differences in the behaviour of structures between these ductility classes, especially the failure mechanism and ultimate collapse acceleration. Despite the fact that a higher behaviour factor of DCH structures influences lower seismic resistance, in comparison to DCM structures, a strict application of the design and detailing rules of Eurocode 8 in analysed examples caused that the seismic resistance of both frames does not significantly differ. The conclusions were derived for two buildings and do not necessarily apply to other RC structures. Further analysis could make a valuable contribution to the analysis of the behaviour of such buildings and decide between two ductility classes in everyday building design.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1997년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Fall 1997
• /
• pp.77-87
• /
• 1997

The earthquake data(M$\geq$4.0) for post-1900 in the Korean Peninsula show temporal variation with active and quiet periods. The pattern is quite similar to northeastern China and Inner Zone of Southwest Japan. Yeongweol earthquake occurred in the seismic gap region of the Korean Peninsula. This is the first medium-size earthquake in inland region of the southern peninsula since 1978. The intensity based on the felt area estimation of about 400 places shows MMI III-Ⅷ in inland region. IIon Cheju Island and Ion Ulreung Island. The isoseismal of MMI Ⅶ shows an elongated circle in the direction of NE-SW and covers some parts of Jungdong-myon, Yeongweol-kun, Sindong-eup and Nam-myun, Jeongseon-kun. There occurred quite strong shaking, numerous cracks on the walls of buildings, falling and movement of slate and tiles on the roofs, falling of tiles from the wall and falling of materials from desks, rook falling from mountain and collapse of gravel lauers on the river side. The least square fitting of the intensity data of the Yeongweol earthquake by a popular intensity attenuation relation yields the following : I=Io＋1.82249 - 0.65295*InR - 0.00707*R

• Geomechanics and Engineering
• /
• 제10권2호
• /
• pp.175-188
• /
• 2016

The construction of a new cavern modifies the state of stresses and displacements in a zone around the existing cavern. For multiple caverns, the size of this influence zone depends on the ground type, the in situ stress, the cavern span and shape, the width of the pillar separating the caverns, and the excavation sequence. Performances of underground twin caverns can be unsatisfactory as a result of either instability (collapse) or excessive displacements. These two distinct failures should be prevented in design. This study simulated the ultimate and serviceability performances of underground twin rock caverns of various sizes and shapes. The global factor of safety is used as the criterion for determining the ultimate limit state and the calculated maximum displacement around the cavern opening is adopted as the serviceability limit state criterion. Based on the results of a series of numerical simulations, simple regression models were developed for estimating the global factor of safety and the maximum displacement, respectively. It was proposed that a proper pillar width can be determined based on the threshold influence factor value. In addition, design charts with regard to the selection of the pillar width for underground twin rock caverns under similar ground conditions were also developed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1509-1513
• /
• 2009

The research of applying reinforced retaining wall due to support the land pressure that given from train's load has been accomplished actively in domestic area. After the retaining wall has been installed, the collapse or partial destruction that generated by effect of train's vibration and repetitive load of train may be induced. Accordingly in the period of using this, the sufficient durability should be guaranteed and years of durability are one hundred and as these are longer than road structure's, the technique that introduced to wall and monitor the long-term strain is necessary. In this paper, the optical fibre is induced vertically to the reinforced retaining wall and after the subsistence of optical fibre is confirmed, the early strain that applied to optical fibre after insertion is monitored. Before and after the concrete placing, damage feasibility of optical fibre is measured by using OTDR(Optical Time Domain Reflectometer) and after concrete is cultivated, the early strain induced to optical fibre is measured by application of BOCDA (Brillouin Correlation Domain Analysis) system.