• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.526-528
• /
• 2003

The effect of heat treatment on torsion characteristics of high nitrogen steel wire has been studied by using torsion test, micro vickers hardness and scanning electron microscopy. After heat treatment at $600{\sim}700^{\circ}C$, the torsion cycle was increased with increasing temperature. Especially, in case of high nitrogen steel wire heat treated at $600^{\circ}C$, the torsion cycle was sharply increased. It is estimated that the cold-worked high nitrogen steel wire started to recrystallize around at $650^{\circ}C$ in air atmosphere.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.35-43
• /
• 2007

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1325W of the laser power, and 1.4m/min of laser welding speed.

• Transactions of Materials Processing
• /
• v.19 no.4
• /
• pp.203-209
• /
• 2010

In the hot press forming process (HPF), a martensitic structure is obtained by controlling the cooling rate when cooling a boron sheet that is heated up to over $900^{\circ}C$. The HPF process has various advantages such as the improvement in formability and material properties and minimal spring back of the deformed materials. The factors related to the cooling rate depend on the heat transfer characteristics between heated materials and dies. Therefore, in this study, the cooling rate is controlled by adjusting the heat transfer coefficient of the material at the pressing process. And, the mechanical properties and microstructure of the deformed material is demonstrated during the HPF process where cold dies are used to form the heated steel plate. This is achieved by varying the major forming conditions that control the cooling rate regarded as the most important process parameter.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.18 no.1
• /
• pp.22-27
• /
• 2004

Seop-Gye divided up the constitution's strength and weakness, and so he cured disease by the 'cold and heat'. 'deficiency and excessiveness' means on the basis of the YINㆍYANG of constitution. He classified constitution with pathogenesis grounding in body formal distinction, flesh hardness and softness, face color and form, skin color. Therefore he grasped the rule of constitution connected with physiological function and pathological distinction, applied the rule of constitution in the diagnosis and cure of the chronic & epidemic febrile disease.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1311-1312
• /
• 2006

Diamond tools were fabricated by cold pressing and sintering under pressure at the temperature up to $750^{\circ}C$. Investigation of the microhardness behaviour of the segments was showed that increasing the cobalt ratio causes the increase of the hardness of the matrix material. This caused to decrease of the wear rate of the matrix. Because the matrix wears more slowly than the diamonds, the space between the cutting edges and the matrix is constantly reduced. The swarf cannot be carried away properly, and the segment will continuously lose its ability to cut with higher cobalt contents.

• Journal of Applied Reliability
• /
• v.17 no.3
• /
• pp.197-206
• /
• 2017

Purpose: Clarify the cause of the noise by the front wheel strut insulator, which is located in close proximity to the driver's seat. Methods: The improvement mechanism was confirmed through failure analysis and reproduction test of the joint generation mechanism. In addition, the main factors were analyzed through principal test. Results: This paper describes the mechanism of occurrence of noise due to deterioration and hardness increase of rubber, deformation on severe road surface, foreign matter and water inflow in cold weather. Conclusion: We found that the insulator and body deformation can be minimized without increasing the thickness of the body and the insulator and reinforcing the body by dispersing the input load by applying load distribution structure instead of the local forming structure of the insulator in the insulator robust structure.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1469-1471
• /
• 2003

The effect of heat treatment on torsion characteristics of high nitrogen steel wire has been studied by using torsion test, micro vickers hardness and scanning electron microscopy. After heat treatment at $600{\sim}700^{\circ}C$, torsion cycle was increased with increasing temperature. Especially, in case of high nitrogen steel wire heat treated at $650^{\circ}C$, torsion cycle was sharply increased. It is estimated that the cold-worked high nitrogen steel wire started to recrystallize around at $640^{\circ}C$ in air atmosphere.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.118-119
• /
• 2006

The development of Fe-based metal matrix composites (MMCs) with high content of hard phase has been approached by combining the use of advanced powder metallurgy techniques like high-energy milling (HEM), cold isostatic pressing (CIP) and vacuum sinterings. A 30% vol. of NbC particles was mixed with Fe powder by HEM in a planetary mill during 10h, characteristing the powder by the observation of morphology and microstructure by scanning electron microscopy (SEM). After of sintering process the variation of density, hardness,carbon content and the microstructural changes observed, permits to find the optimal conditions of processing. Afterwards, a heat treatment study was performed to study the hardenability of the composite.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.69-77
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties were decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the In atmospheric gas($H_2$ : 75%, $N_2$ : 25%) and the HNx atmospheric gas($H_2$ : 5%, $N_2$ : 95%) We confirmed the following characteristics, mechanical properties were changed under the influence of the annealing cycle and the atmospheric gas. And, we have some result according to heat treatment method. Elongation of the mechanical properties in the HNx BAF is higher than the Ax BAF. But tensile strength and hardness is higher than the HNx BAF.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.1
• /
• pp.10-16
• /
• 2021

Exhaust manifold is a very important component that is directly connected to air environment pollution and that requires strict mechanical properties such as high temperature fatigue and oxidation. Among stainless steels, the ferritic stainless steel with body-centered cubic structure shows excellent resistance of stress-corrosion cracking, ferromagnetic at room temperature, very excellent cold workability and may not be enhanced by heat treatment. The microstructural characteristics of four cast ferritic stainless steels which are high heat-resistant materials, were analyzed. By comparing and evaluating the mechanical properties at room temperature and high temperature in a range of 400℃~800℃, a database was established to control and predict the required properties and the mechanical properties of the final product. The precipitates of cast ferritic stainless steels were analyzed and the high-temperature deformation characteristics were evaluated by comparative analysis of hardness and tensile characteristics of four steels at room temperature and from 400℃ to 800℃.