• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.225-230
• /
• 2002

As in most metal forming processes, die and lubrication are of vital importance in hydrostatic extrusion. An efficient die design and lubrication system selection reduce the pressure required for a given reduction ratio by lowering friction at the billet-die interface. In contrast to the conventional macroscopic extrusion, fine-wire fabrication requires higher extrusion pressure and effect of friction is much more significant. Forming fine Au, Ag, and Cu wire with hydrostatic extrusion process in cold condition, the effect of extrusion die angle, lubrication and billet's initial diameter was studied.

• 한국정밀공학회지
• /
• 제17권10호
• /
• pp.77-82
• /
• 2000

The design of the prestressed cold extrusion die with two stress rings has been performed in this study. The cold extrusion has been simulated by the rigid-plastic FEM. The stress analysis of die has been performed for both after shrink fitting and during extrusion by using the elastic FEM and the Lame's equation. According to the variation of interferences and diameter ratios, the maximum effective stress has been evaluated. As results, interferences and diameters were determined by the minimization of the maximum effective stress of die insert. The comparison of the maximum effective stress between the proposed design and the conventional design has been discussed. It was found that the maximum effective stress in the die insert is considerably affected by the stiffness of the first stress ring.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.153-158
• /
• 2006

Nowadays, hollow upper-shaft of monobloc type has been considered for weight reduction and high quality in the automobile industry. To form the upper-shaft under tube cold extrusion, Taguchi method is applied to optimize the die design in this study. Taguchi method for optimum die design is to establish the optimal combination of design parameters and to reduce a number of experiments. Effect of parameters including the die relief, mandrel, die half angle is investigated and analyzed based on FEA analysis using a FEM commercial software MSC_Marc. Furthermore extrusion experiments have been performed to verify the results investigated in the FEM simulations.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.713-716
• /
• 2002

The dimensional accuracy of the cold forged products is strongly dependent on the elastic behavior of the die. The elastic deformation of the die is continuously changed during the process. Therefore, it is needed to measure the deformation of die. Strain gauges are used to measure the elastic strains in the die during cold backward extrusion process. The strain gauges are attached on the die surface and embedded at the interface between the die insert and the stress ring. In order to compare the results with the FE-analysis, the rigid-plastic FE-analysis of cold backward extrusion process using DEFORM-3D has been performed, and the analysis of elastic deformation of the die has been done by using ANSYS with non-linear contact.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.584-588
• /
• 1997

Lots of forginfs used in automobile and aerospce industries are made in hot or cold working conditions, depending on the size and shape of a product. Usually the die design for new items has been first made on the basis of experiences and many know-hows accumulated in the company and then slightly modified through trial and error method to get the desired forgings without defects. Most of drawings at the die design stage have been manually drawn, butrecently some of forging companies have begun to apply a computer-aided drafting technique to the die design for reducing drafting time as well as repeatedly utilizing standardized parts form registerd data base. In this paper the automated die design technique for forward extrusion of axisymmetric forgings is developed by using AutoLISP language. For this study the representative die system is determined form the investigation of several types of forging dies being currently employed in the metal forming field and the design rules for cold extrusion die are summarized and programmed on a personal computer. A few design examples of forward extrusion die are given and discusses.

• 한국정밀공학회지
• /
• 제13권11호
• /
• pp.106-113
• /
• 1996

Using stainless steel as the cold forged parts especially the outer parts of automobile is gradually increasing because it can bear up against the erosion and the wear. During cold forging of the stainless steel the working pressure acting on die surface are very high therefore the wear on die surface can be greatly increased. In cold forging processes, die failure must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The die wear affects the tolerances of forged parts, metal flow and costs of processes etc. The only way to to control these failures is to develop methods which allow prediction of the die wear and which are suited to be used in the desing stage in order to optimize the process. In this paper, the rigid-plastic finite element method was combined with the wear prediction routine and then the forward extrusion process using stainless steel was analysed simultaneously. To minimize the die wear the FPS algorithm was applied and the optimal conditions of die configuration are suggested.

• 한국정밀공학회지
• /
• 제16권2호통권95호
• /
• pp.87-94
• /
• 1999

The automated die design program is developed for cold forging of axisymmetric parts which are mainly produced by forward extrusion, backward extrusion, composite extrusion and upsetting. For this study, firstly classification of forged parts and investigation of die construction type usually employed in forging industry are carried out and the most proper type from several kinds of die construction is proposed as a standardized one. Based on the die design rules summarized in the references such as handbooks, technical papers, monthly journals, etc. the automated die design program was made using AutoLISP language available in AutoCAD software of personal computer. This program interactively runs for only input data, for example, forging process, shape of forged parts, type of punch, split of die insert and design of shrinkage rings and then displays details of drawings necessary to make a forging die. When a variety of forging processes and forged parts are tested to examine the validity of this program, it was confirmed to give good results applicable to the forging die design in press shop.

• 소성∙가공
• /
• 제11권4호
• /
• pp.355-362
• /
• 2002

In this study, an axi-symmetric finite element program for elastic analysis of the die set shrink fitted in cold extrusion was developed. The geometrical constraint according to shrink fit was enforced by employing the Lagrange multiplier method. The numerical results for strain and stress distributions in the die set including single and multi stress rings assembled by shrink fit were compared well with the Lame's equation for thick-walled solution available in the literature. To extend the applicability of the analysis program developed, various cases without or with stress ring and with pre-stress applied on stress ring were numerically investigated as well. This numerical approach enables the optimization study to determine optimal dimensions of die set to improve tool life for practical use in industry.

• 동력기계공학회지
• /
• 제3권1호
• /
• pp.45-49
• /
• 1999

Lots of products are made in various working conditions, depending on the size and the shape of them. Usually, at first, the die for new items had been designed on the basis of experience and know-how, and then modified through trial and error. At a die design stage most of drawings have been drawn manually. Recently some forging companies save design time by repeated utilization of standardized parts with registered data base. In this study the automated die design technique for forward extrusion of axisymmetric products is developed. A standardized die system is proposed from the investigation of ones employed frequently in the metal forming field and the design rules for cold extrusion die. A design example of forward extrusion die is given and discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.83-87
• /
• 2000

The die for cold forging gets a ver high axial load and radial pressure during processing and hence deforms considerably in the radial direction. This radial deformation of die becomes a important factor influencing the dimensional accuracy of a product. In order to obtain a product with highly accurate dimension therefore it is essential to acquire some information on elastic deformation of the die and the product. The study has been performed for the relation of the deformation between a die and a product in backward extrusion. The strain of the die has been given by the simple experiment using the strain gauges attached to the outer surface of the die. Also the history of the deformation of the die and the product has been given by the experiment and Lames' formula. The results has been compared with the previous another method. The study has given useful results for the deformation history of the die and the product through the experiment and Lame's formula in backward extrusion which can be applied in the die design for the product with accurate dimension