• Horticultural Science & Technology
• /
• v.29 no.2
• /
• pp.81-86
• /
• 2011

The effects of girdling on fruit quality and cold resistance of 'Kyoho' grapes were investigated. Girdling treatment was conducted on the trunk at 10 cm above ground with 1 cm width and grapes were harvested at 90 and 110 days after full bloom to compare the fruit quality. First harvesting rate in girdling treatment was higher than that in non-girdling treatment and coloration was also higher in girdled vines at the final harvest. In other words, coloring process of grape was promoted and enhanced by girdling, but this effect of coloring improvement was decreased after successive girdling treatment. Fruit quality showed no difference between the treated and non-treated berries, but fruit cracking rate was lower in girdled treated berries. Girdled trees were weakened and suffered from freezing damage. Especially, most grapevines withered up after being girdled for three consecutive years. Although girdling had effect on improving the berry coloring significantly, the effect wore off with continuous girdling. And it was possible that consecutive girdling leaded to wither and growth suppression especially in grapevines. These adverse effects may make the continuous girdling technique unsuitable in practice for 'Kyoho' grape.

• Journal of the Korean Ceramic Society
• /
• v.50 no.2
• /
• pp.142-148
• /
• 2013

Conventional cold isostatic pressing, slip casting, and filter pressing are not completely suitable for fabricating large plates because of disadvantages such as the high cost of equipment and formation of density gradient. These problems could be avoided by employing pressure-vacuum hybrid slip casting (PVHSC). In the PVHSC, the consolidation occurs not only by the compression of the slip in casting room, but also by vacuum sucking of the dispersion medium around the mold. We prepared the alumina bodies by the PVHSC in a static- or stepwise-pressure manner for loading up to 0.5 MPa using an aqueous slip. The green bodies were dried at $30^{\circ}C$ with 40 ~ 80% relative humidity. Under static pressure, casting induced a density gradient in the formed body, resulting in cracking and distortion after the firing. However, the stepwise pressure loading resulted in green bodies with homogeneous density, and the minimization of the appearance of those defects in final products. Desirable drying results were obtained from the cast bodies dried with 80% RH environment humidity. When sintered at $1650^{\circ}C$ for 4 h, the alumina plate made by stepwise-pressure casting reached full density (> 99.7% relative density).

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.7 no.1
• /
• pp.7-14
• /
• 2001

The amount of petroleum consumption has been Increased according to the industrialization and It leads to the increase of the possibility of marine oil pollution. In Korea, some countermeasures including oil skimmer, gelling agent and herding agent of oil have been used for the remediation of the pollution. However, most of them have lets of shortcomings in the application under in-situ condition, because they are sensitive to the situation such as geographical feature, the wind and the tide. In reported literature, the natural powdered oil absorbent which is made of peat moss is an effective mean to clean spilled oil from lake or coast. However, the peat moss is a natural resource which is only Produced from a specific cold weather are like Canada. This indicates that the alternative materials which is readily obtained from everywhere are needed for powdered oil absorbent. Therefore. in the study, same natural materials including pine leaves and straw are tested as the alternative materials for the absorbent. The raw materials were dried and treated by heat at various temperature during several Periods and then. shattered by a grain cracking machine. The oil sorption capacity of the prepared materials was compared according to the methods of heat treatment and their sizes. The proportion of hydrogen cyanide to combustion of the absorbents was measured to confirm their final disposal methods. The biodegradability test of the absorbents was carried our to evaluate possibility of a side pollution in the coast. In was found that the heat treatment of pine leaves enhanced the capacity of oil sorption and decreased the water sorption. The maximum oil sorption was observed for the material treated at 18$0^{\circ}C$for 60 min. The amount of hydrogen cyanide from the combustion were 0.09ml/g, 0.07ml/g for pine leaves and straw respectively meaning that the final disposal by combustion might be feasible. The amount or organic carbon extracted from pine leaves during 7 days was up to 0.015g organic carbon from one gram of pine leaves. but the degradation was as fast as for glucose. It is concluded that the pine leaves can be served as a good raw material for the powdered oil absorbent like peat moss.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.39-39
• /
• 2009

고강도강의 용접성은 저온균열 저항성으로 대변되는데, TMCP강과 HSLA강 등이 개발되면서 고강도강의 저온균열저항성이 크게 향상되어 무예열 용접성이 확보되었다. 그러나 용접재료 측면에서는 그에 상응하는 재료의 개발이 지연되어 용착금속부에서의 저온균열이 심각한 문제로 대두되고 있는 실정이다. 이러한 문제는 800 MPa급인 HY-100강재를 HSLA-100강으로 대체하는 과정에서 현실적인 문제로 제기 되었다. 즉 HSLA강은 용접 예열이 필요치 않았으나 기존의 용접재료, 즉 HY-100 강재에 사용하던 용접재료를 사용하게 되면 용착금속부에서 저온균열이 발생하여 용접예열을 생략할 수 없다는 판단에 이르게 되었던 것이다. 이에 본 연구의 목적은 HSLA-100강을 무예열 용접할 수 있는 GMA 용접와이어 개발하는 것이며, 구체적인 개발 목표는 무예열 용접조건에서 800 MPa 이상의 인장강도를 가지며 $-50^{\circ}C$에서의 충격인성이 50 J 이상인 GMA 용접와이어 개발하는 것이다. 이러한 용접재료를 합금설계함에 있어 무예열 용접성을 확보하기 위하여 용접재료의 탄소함량을 0.01% 수준으로 하고, 용착금속의 인장강도와 저온 충격치에 미치는 Mn과 Mo 함량의 영향을 검토하고 각각의 조성을 실험계획법으로 확정하였다. 그리고 확산성수소량에 따른 저온균열 발생 여부를 확인하여 무예열용접성을 확보하기 위해서는 확산성수소량이 3ml/100g 이하가 되어야 한다는 사실을 실험적으로 확인하였다. 그리고 이를 달성하기 위해서는 원자재인 와이어로드의 표면 품질이 중요하다는 사실도 확인할 수 있었다. 다음으로는 실험계획법에 의거하여 선정된 합금조성의 신뢰성을 검증하기 위하여 800kg 중량의 시제품을 생산하였으며, 생산된 시제품에 대해서는 실험계획법에서 사용한 Ar+5%CO2외에도 Ar+20%CO2를 적용하여 보호가스의 영향을 검토하였다. 검토 과정에서 Ar+20%CO2용으로 사용하기 위해서는 용접재료의 Si 및 Mn 함량이 상향조정되어야 함을 확인할 수 있었다. 그리고 탄소함량을 0.05% 수준으로 증가시키면 Mo 함량을 크게 저하시킬 수 있음도 확인할 수 있었다. 이러한 과정을 거쳐 개발된 GMA 용접재료는 무예열 용접조건에서 저온균열이 발생하지 않았으며, 인장강도는 830 MPa이었으며 $-50^{\circ}C$에서의 충격치는 90 J 이상이었다.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.118-118
• /
• 2009

자동차의 경량화, 안전성 그리고 내식성 향상을 위하여 고강도 강판 및 도금 강판의 적용이 증가하면서 자동차 산업의 많은 부분에서 적용되는 저항 점용접에서도 고강도 강판과 도금강판의 적용이 증가하는 추세이다. 이에 따라 고강도 강판과 도금 강판의 낮은 용접성을 개선하기 위하여 기존의 단상 AC 용접기에서 전류 파형의 형태를 개선한 인버터 DC 용접기가 차체 조립라인에서 많이 사용되고 있다. 본 연구에서는 고강도 강판의 저항 점용접의 연속타점 시 단상 AC용접기와 인버터 DC용접기의 전극의 연속타점 수명의 차이를 비교하고 분석하기 위해 590MPa 급 전기아연도금강판을 이용하여 AWS 규격에 연속타점실험을 기준으로 단상 AC 와 인버터 DC 용접기의 연속타점 실험을 실시하였다. 연속타점실험 중에 전극의 형상관찰을 위해 100타점 간격으로 carbon paper를 이용해 전극 직경 변화를 관찰 하였으며, 100 타점간격으로 동저항을 측정하고 인장 전단 시편과 Peel test 시편을 제작하여 연속타점 시 단상 AC와 인버터 DC 용접기의 저항 점용접 연속타점 수명을 비교 분석하였다. 그리고 연속타점 실험 후 사용된 전극의 표면과 단면 형상을 각각 OM, SEM, EDX로 분석하여 전극 표면의 Zn과 합금화 된 전극의 합금층을 분석하였다. 그 결과 590MPa급 전기아연도금강판의 저항 점용점 연속타점 수명평가에서 인버터 DC 용접기가 단상 AC 용접기보다 200타점 더 우수한 연속타점 수명을 보유하였다. 특히 인장강도 기준 측면에서는 인버터 DC 용접기의 전극 연속타점수명은 매우 우수하다.

• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.42-46
• /
• 2016

Hydrogen assisted cracking (HAC) is one of the most complicated problem in welding. Huge amount of studies have been done for decades. Based on them, various standards have been established to avoid HAC. But it is still a chronic problem in industrial field. It is well known that the main causes of the hydrogen crack are residual stress, crack susceptible micro structures and a certain critical level of hydrogen concentration. Even though the exact generating mechanism is unclear till today, it has been reported that the hydrogen level in the weld metal should be managed less than a certain amount to prevent it. Matsuda studied that the residual hydrogen level in the weld metal can be varied even if the initial hydrogen content is same. It is also insisted in this report that the residual hydrogen concentration is in stronger correlation with hydrogen crack than the initial hydrogen content. But, in practical point of view, the residual hydrogen is still hard to consider because measuring hydrogen level is time and cost consuming process. In this regard, numerical analysis is the only solution for considering the residual hydrogen content. Meanwhile, Takahashi showed the possibility of predicting the residual hydrogen by a rigorous FE analysis. But, few commercial software suitable for solving the weld metal hydrogen has been reported yet. In this study, two dimensional thermal - hydrogen coupled analysis was developed by using the commercial FE software MARC. Since the governing equation of the hydrogen diffusion is similar to the heat transfer, it is shown that the heat transfer FE analysis in association with hydrogen diffusion property can be used for hydrogen diffusion analysis. A series of simulation was performed to verify the accuracy of the model. For BOP (Bead-On-Plate) and the multi-pass butt welding simulations, remaining hydrogen contents in the weld metal is well matched with measurements which are referred from Kim and Masamitsu.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.3
• /
• pp.299-310
• /
• 2019

Increase of combat capability through the lightweighting of vehicles has been internationally issued. One of the methods for lightening is applying high hardness armor(HHA) steel which is outstanding ballistic performance and protection performance compared to weight. Development of HHA steel is currently completed in America, United Kingdom, Australia and Germany. It is used for not only combat vehicle, but also various combat device. Korea is developing new material of HHA steel according to this trend. When such HHA steel is applied to structure, welding process is used for connection of the structure. Cracks from hydrogen embrittlement and cold cracking are easily generated in welds of HHA steel and it greatly affects the strength of all structure. Decrease of strength from welding defect is critical to combat capability. Therefore, welding process optimization is important for performing the role of structure. In this study, international welding technology is reviewed through scientific research paper and patent.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.1
• /
• pp.219-225
• /
• 2019

Computing low temperature performance of asphalt mixture is one of the important tasks especially for cold regions. It is well known that experimental creep testing work is needed for computation of thermal stress and critical cracking temperature of given asphalt mixture. Thermal stress is conventionally computed through two steps of computation. First, the relaxation modulus is generated thorough the inter-conversion of the experimental creep stiffness data through the application of Hopkins and Hamming's algorithm. Secondly, thermal stress is numerically estimated solving the convolution integral. In this paper, one-step thermal stress computation methodology based on the Laplace transformation is introduced. After the extensive experimental works and comparisons of two different computation approaches, it is found that Laplace transformation application provides reliable computation results compared to the conventional approach: using two step computation with Hopkins and Hamming's algorithm.

• Advances in materials Research
• /
• v.8 no.2
• /
• pp.117-135
• /
• 2019

The lifetime of a gas turbine combustor is typically limited by the durability of its liner, the structure that encloses the high-temperature combustion products. The primary objective of the combustor thermal design process is to ensure that the liner temperatures do not exceed a maximum value set by material limits. Liner temperatures exceeding these limits hasten the onset of cracking which increase the frequency of unscheduled engine removals and cause the maintenance and repair costs of the engine to increase. Hot gas temperature prediction can be considered a preliminary step for combustor liner temperature prediction which can make a suitable view of combustion chamber conditions. In this study, the temperature distribution of ceramic panels for a V94.2 gas turbine combustor subjected to realistic operation conditions is presented using three-dimensional finite difference method. A simplified model of alumina ceramic is used to obtain the temperature distribution. The external thermal loads consist of convection and radiation heat transfers are considered that these loads are applied to flat segmented panel on hot side and forced convection cooling on the other side. First the temperatures of hot and cold sides of ceramic are calculated. Then, the thermal boundary conditions of all other ceramic sides are estimated by the field observations. Finally, the temperature distributions of ceramic panels for a V94.2 gas turbine combustor are computed by MATLAB software. The results show that the gas emissivity for diffusion mode is more than premix therefore the radiation heat flux and temperature will be more. The results of this work are validated by ANSYS and ABAQUS softwares. It is showed that there is a good agreement between all results.

• The Journal of the Korea Contents Association
• /
• v.15 no.9
• /
• pp.576-587
• /
• 2015

This paper presents a quantitative evaluation of water permeability in concrete with cold joint considering mineral admixture and loading conditions. Concrete samples with OPC (Ordinary Portland Cement) and GGBFS(Ground Granulated Blast Furnace Slag) are prepared considering 0.6 of W/C ratio and 40% of replacement. 30% and 60% loading levels for compression and 60% loading level for tension are induced to concrete samples. In compression conditions, the permeability in control case shows $2.41{\times}10^{-11}m/s$ in OPC concrete, and it changes to $2.07{\times}10^{-11}m/s$ (30% of peak) and $2.36{\times}10^{-11}m/s$ (60% of peak). The results in GGBFS concrete shows the same trend, which yields $2.17{\times}10^{-11}m/s$ (control), $1.65{\times}10^{-11}m/s$ (30% of peak), and $1.96{\times}10^{-11}m/s$ (60% of peak), respectively. In tensile conditions, the permeability increases from $2.37{\times}10^{-11}m/s$ (control) to $2.67{\times}10^{-11}m/s$ (60% of peak) while that in GGBFS concrete increases from $2.17{\times}10^{-11}m/s$ (control) to $2.24{\times}10^{-11}m/s$ (60% of peak). Permeability coefficients decreases in 30% of compressive level but increases in 60% level, while results in tensile level increases rapidly. This shows pore structure in concrete is condensed and with loading and permeability increases due to micro-cracking. Permeability evaluation considering the effects of loading conditions, cold joint, and GGBFS is verified to be important since water permeability greatly changes due to their effects.