• ETRI Journal
• /
• v.37 no.5
• /
• pp.940-944
• /
• 2015

We present a frame synchronization algorithm for lowdensity parity-check (LDPC) coded burst transmissions, which combines a conventional pilots-assisted frame synchronization algorithm and a code-aided algorithm based on the mean magnitude of the soft outputs from the LDPC decoder. With moderate computational complexity, the proposed algorithm is more efficient in bandwidth than conventional pilots-assisted algorithms. When compared with other code-aided algorithms, the proposed algorithm offers a better trade-off between complexity and performance. Simulation results in the case of an 8-PSK system with (1944, 972) LDPC code show that the proposed algorithm can achieve a performance equivalent to that of the perfect frame synchronization, with a bandwidth efficiency loss of 0.06 dB due to the use of pilot symbols.

• Journal of Communications and Networks
• /
• v.2 no.1
• /
• pp.58-68
• /
• 2000

In this paper we introduce the correlation-aided distributed sample acquisition (CDSA) scheme for fast cell search in IMT-2000 W-CDMA cellular system. The proposed scheme incorporates the state symbol correlation process into the comparison-correction based synchronization process of the original DSA scheme to enable fast acquisition even under very poor channel environment. for its realization, each mobile station (MS) has to store in its memory a set of state sample sequences. which are determined by the long-period scrambling sequences used in the system and the sampling interval of the state samples. CDSA based cell search is carried out in two stages : First, the MS first acquires the slot timing by using the primary synch code (PSC) and then identifies the igniter code which conveys the state samples of the current cell . Secondly. the MS identifies the scrambling code and frame timing by taking the comparison-correction based synchronization approach and, if the identification is not done satisfactorily within preset time. it initiates the state symbol correlation process which correlates the received symbol sequence with the pre-stored state sample sequences for a successful identification. As the state symbol SNR is relatively high. the state symbol correlation process enables reliable synchronization even in very low chip-SNR environment. Simulation results show that the proposed CDSA scheme outperforms the 3GPP 3-step approach, requiring the signal power of about 7 dB less for achieving the same acquisition time performance in low-SNR environments. Furthermore, it turns out very robust in the typical synchronization environment where large frequency offset exists.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.21-31
• /
• 1998

This study described computer aided die design system for cold forging of non-axisymmetric parts. To design the die of cold forging. an integrated approach based on a rule-base system and commercial F. E. code were adopted. This system is implemented on the personal computer and its environment is a commercial CAD package named as AutoCAD. The system includes four modules. In the initial data input module, the variables which are necessary to design of die are inputted by user and die material are selected from the database. In the analysis and redesign module, stress distrubution action on the designed die is analyzed by commercial FEM code NISA II. The designed die is modified to prevent failure in both states of stress free and pressurizing. The developed system provides powerful capabilities for die design of non-axisymmetric parts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.591-594
• /
• 2002

Generating NC-code from 3D part model needs a lot of effort to make many decisions, including machining area, tool change data, tool data, cutting condition, etc., by using either manual or computer aided method. This effort can be reduced by integration of automated process planning and NC-code generation. In case of generating NC code with a help of the process planning system, many data mentioned from the process planning can be used. It means that we can create NC-code about a full part. In this study, integration of FAPPS(Feature based Automatic Process Planning) with a NC-code generating module is described and additional data to adapt NC-code for machine shop is discussed.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.7
• /
• pp.3156-3167
• /
• 2020

One drawback of polar codes is that they are not universal, that is, to achieve optimal performance, different polar codes are required for different kinds of channel. This paper proposes a polar code construction scheme for Nakagami-m fading channel. The scheme fully considers the characteristics of Nakagami-m fading channel, and uses the optimized Bhattacharyya parameter bounds. The constructed code is applied to an orthogonal frequency division multiplexing (OFDM) system over Nakagami-m fading channel to prove the performance of polar code. Simulation result shows the proposed codes can get excellent bit error rate (BER) performance with successive cancellation list (SCL) decoding. For example, the designed polar code with cyclic redundancy check (CRC) aided SCL (L = 8) decoding achieves 1.1dB of gain over LDPC at average BER about 10^-5 under 4-quadrature amplitude modulation (4QAM) while the code length is 1024, rate is 0.5.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.6A
• /
• pp.660-666
• /
• 2004

Transmitted data may be compensated by using estimated channel values that are obtained with pilot symbols in OFDM-CDMA systems. Generally, a USE (Minimum Mean-Squared Error) estimator using correlations between pilot symbols gives good results, but its structure is so complicated. Starting with a modification of PA (Pilot-Aided) algorithm using pilot symbols and PADD (Pilot-Aided Decision-Directed) algorithm using both pilot and data symbols, a new channel estimation algorithm with more simpler structure is proposed. The performance of this algorithm is evaluated with varying mobile speed in a Ralyleigh multipath fading environment through computer simulations. The simulation results show that the proposed channel estimation algorithm outperforms a conventional PA algorithm.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.6
• /
• pp.66-74
• /
• 2010

Recently distributed video coding (DVC) is spotlighted for the environment which has restriction in computing resource at encoder. Wyner-Ziv (WZ) coding is a representative scheme of DVC. The WZ encoder independently encodes key frame and WZ frame respectively by conventional intra coding and channel code. WZ decoder generates side information from reconstructed two key frames (t-1, t+1) based on temporal correlation. The side information is regarded as a noisy version of original WZ frame. Virtual channel noise can be removed by channel decoding process. So the performance of WZ coding greatly depends on the performance of channel code. Among existing channel codes, Turbo code and LDPC code have the most powerful error correction capability. These channel codes use stochastically iterative decoding process. However the iterative decoding process is quite time-consuming, so complexity of WZ decoder is considerably increased. Analysis of the complexity of LPDCA with real video data shows that the portion of complexity of LDPCA decoding is higher than 60% in total WZ decoding complexity. Using the HDA (Hard Decision Aided) method proposed in channel code area, channel decoding complexity can be much reduced. But considerable RD performance loss is possible according to different thresholds and its proper value is different for each sequence. In this paper, we propose an adaptive HDA method which sets up a proper threshold according to sequence. The proposed method shows about 62% and 32% of time saving, respectively in LDPCA and WZ decoding process, while RD performance is not that decreased.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.7A
• /
• pp.682-688
• /
• 2006

In this paper, a soft-decision method for initial PN code acquisition in pilot-channel aided Direct Sequence Code Division Multiple Access (DS-CDMA) systems is proposed in order to improve the acquisition performance. We apply this technique to the conventional hybrid search algorithm and analyze it in terms of mean code acquisition time. For the analysis, we present mathematical model of proposed algorithm and also perform the simulation under IMT-2000 channel models. Numerical results show that our proposed scheme outperforms the conventional one by 0.2 - 0.4 sec with respect to the mean code acquisition time because the soft decision technique can mitigate the possible decline in search performance caused by the use of a hard-decision technique.

• Journal of the Korean Society of Industry Convergence
• /
• v.5 no.1
• /
• pp.11-19
• /
• 2002

This study described computer aided die design system for cold forging of non-axisymmetric parts such as gears and splines. To design the cold forging die, an integrated approach based on a rule-base system and commercial F. E. code were adopted. This system is implemented on the personal computer and its environment is a commercial CAD package named as Auto CAD. The system includes four modules. In the initial data input module, variables which are necessary to design of die are inputted by user and die material are selected from the database according to the variables. In the analysis and redesign module, stress distribution acting on the designed die is analyzed by commercial FEM code NISA II with elastic mode. If die failure predicted, the designed die would modified in four ways to prevent die failure in both states of stress free and pressurizing. The developed system provides useful date and powerful capabilities for die design of non-axisymmetric parts.

• International Journal of CAD/CAM
• /
• v.9 no.1
• /
• pp.121-128
• /
• 2010

The purpose of this study is to clarify the mechanical behavior of human lumbar vertebrae (L3/L4) with and without fusion bone under physiological axial compression. The author has developed the program code to build the patient specific three-dimensional geometric model from the computed tomography (CT) images. The developed three-dimensional model provides the necessary information to the physicians and surgeons to visually interact with the model and if needed, plan the way of surgery in advance. The processed data of the model is versatile and compatible with the commercial computer aided design (CAD), finite element analysis (FEA) software and rapid prototyping technology. The actual physical model is manufactured using rapid prototyping technique to confirm the executable competence of the processed data from the developed program code. The patient specific model of L3/L4 vertebrae is analyzed under compressive loading condition by the FEA approach. By varying the spacer position and fusion bone with and without pedicle instrumentation, simulations were carried out to find the increasing axial stiffness so as to ensure the success of fusion technique. The finding was helpful in positioning the fusion bone graft and to predict the mechanical stress and deformation of body organ indicating the critical section.