• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.2 s.110
• /
• pp.70-77
• /
• 2005

For the purpose of developing liner board for water resistant corrugated board in the cold chain system, several types of base paper for corrugated board were purchased from the market and 6 different boards were produced in the mill by applying the chemicals, chosen in the previous studies, on the base paper. Then water-moisture resistance and physical properties of the boards were compared each other. The liner board which is dried at high temperature with pressure by Condebelt (CK paper) showed a superior performance in strength over common liner boards. Strength of the board increased by surface chemical treatment up to $60\%$ of compressive strength and $30\%$ of burst strength. Starch insolubilization with Ammonium Zirconium Carbonate and surface coating with a surface sizing agent and a moisture resistant chemical on CK paper showed the best result. Therefore this method was recommended to produce the outer liner board for water resistant corrugated board.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1154-1158
• /
• 2003

Hydrothermal deposition of hydroxyapatite coatings on $Al_2$O$_3$ substrates was studied using aqueous solutions of Ca(NO$_3$)$_2$ㆍ4$H_2O$ and (NH$_4$)$_2$HPO$_4$ containing EDTA disodium salt as a chelating agent for $Ca^{2+}$. For the precipitation of the coatings the EDTA-Ca$^{2+}$ chelates were dissociated thermally at 20$0^{\circ}C$ or decomposed by oxidation with $H_2O$$_2$ at 9$0^{\circ}C$. Scanning electron microscopy and X-ray diffraction were used to investigate the deposition behavior and the phase of the coatings. Hydroxyapatite coatings were not deposited with the thermal dissociation method, whereas uniform deposition of the coatings (about 0.7 $\mu\textrm{m}$ thickness) was obtained with the oxidative decomposition method. The coatings consisted of fine rod-like hydroxyapatite crystals (hexagonal structure) with 60-80 nm diameters, having some preferred orientation with their length (i.e., the c axis) perpendicular to the substrate.ate.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.6
• /
• pp.246-249
• /
• 2011

Surface modification before coating nickel by coupling agents and/or etchant of glass did not provide enough adhesive strength of electroless nickel deposits on glass. Effect of heat treatments on hardness as well as adhesion of nickel deposits was studied by using tape test for adhesion, nanoindenter for hardness and glancing angle x-ray diffractometer (GAXRD) for phase characterization. Heat treatment improved hardness as well as adhesion. XRD results give that the improvements of adhesion and hardness are due to the formation of $NiSiO_4$ around the interface between the nickel deposits and the glass and the precipitation of $Ni_3P$ causing precipitation hardening, respectively. The details in effects of heat treatment on adhesion and hardness are described here.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.541-541
• /
• 2012

InP quantum dots capped by myristic acid (InP-MA QDs) were synthesized by a typical hot injection method using MA as stablizing agent. The current density across the InP-MA QDs thin film which was fabricated by spin-coating method is about $10^{-4}A/cm^2$ at the electric field of 0.1 MV/cm from I-V measurement on a metal-insulator-metal (MIM) device. The low conductivity of the InP-MA QDs thin film is interpreted as due to the long interdistances among the dots governed by the MA molecules. Therefore, replacing the MA with thioacetic acid (TAA) by biphasic ligand exchange was conducted in order to obtain TAA capped InP QDs (InP-TAA). InP-TAA QDs were designed due to: 1) the TAA is very short molecule; 2) the thiolate groups on the surface of the InP-TAA QDs are expected to undergo condensation reaction upon thermal annealing which connects the QDs within the QD thin film through a very short linker -S-; and 3) TAA provides better passivation to the QDs both in the solution and thin film states which minimizing the effect of surface trapping states.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.10
• /
• pp.1515-1519
• /
• 2005

Tungsten oxide-modified TiO2 thin films were formed on a glass substrate by sol-gel and dip coating processes using acetyl acetone as a chelating agent. The hydrophilic properties of the thin films were investigated with illumination of UV light. The dependence of water contact angle on material composition and morphology of the film is established with SEM image and AFM profile. The surface morphology was controlled with the change of precursor concentration. 0.01 M of tungsten oxide-modified Ti$O_2$ have shown the highest hydrophilicity after UV-irradiation. The effect of composition on photoinduced hydrophilicity of the W$O_3$-Ti$O_2$ films was also investigated. The films were characterized by XRD, SEM, AFM and XPS.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2005.11a
• /
• pp.133-147
• /
• 2005

In order to investigate applicability for 2,2,2-trifluoroethyl methacrylate (TFEMA) produced by esterification of 2,2,2-trifluoroethanol(TFEA) and methacrylic acid(MA) using pervaporation membrane, poly(vinyl alcohol) (PVA) composite membranes were prepared with glutaraldehyde(GA) onto porous polyethersulfone(PES) support. The degree of crosslinking and thickness of PVA coating layer were analyzed by swelling test and SEM(scanning electron microscopy), respectively. Pervaporation test was done with two feed mixures; TFEA/water, MA/water. The pervaporation data were obtained as a function of content of crosslinking agent, feed composition, and operating temperature, respectively. In case of TFEA-water(90/10 wt%) feed mixture at $80^{\circ}C$, the optimized membrane showed the high permeation flux of 1.5 $kg/m^2hr$ and separation factor of 320. In case of MA-water(90/10 wt%) feed mixture, the membranealso showed high permeation flux of 2.3 $kg/m^2hr$ and separation factor of 740 in same conditions.

• Microbiology and Biotechnology Letters
• /
• v.24 no.5
• /
• pp.546-552
• /
• 1996

The applicability of chitosan, a biodegradable natural polymer, as the coating material to prevent the dispersal of the spores of the apple white rot agent Botryosphaeria dothidea, was investigated. The physical properties of mixed chitosan/polyvinyl alcohol(PVA) film showed the increased physical properties for film formation, such as tensil strength, elongation, and viscosity, compared to either chitosan or PVA film. The FT-IR spectra of chitosan/PVA film indicated that the film was formed by simple blending not by any new synthetic bond. The chitosan and chitosan/PVA film showed effective antifungal activity on B. dothidea. The formed films were well decomposed by ASTM strains used for biodegradability test, on the other hand, the PVA film could not be decomposed by above standard strains. The field test at apple orchard showed that the dispersal of B. dothidea spores could be effectively reduced by coated film, especially by chitosan/PVA film. The spore dispersal was reduced upto 97.0% by 1.0% chitosan/5.0% PVA film during 4 months.

• Journal of the Korean institute of surface engineering
• /
• v.26 no.6
• /
• pp.291-298
• /
• 1993

In order to substitute for porous nickel anode in Molten Carbonate Fuel Cell(MCFC), porous cermet elec-trode was fabricated with Ni and Ni-P coated ceramic powder. Ni and Ni-P were coated by electroless plat-ing method in the nickel solution containing of hydrazine and sodium hypophosphate as a reducing agent. The plating solution was stirred by air and mechanical agitator. Ultrasonic irradiation was applied to the plating bath to improved the effect of agitation and coating speed. Electorde was formed by pressing method and doc-tor blade method followed by sinterd at$ 800^{\circ}C$ for 6 hours in H2 environment. Anode performance test carried out by potentiodynamic polarization technique in the MCFC operating condition and 154-161mA/$\textrm{cm}^2$ as ob-tained as a anode current density at the+100mV overpotential.

• Journal of Microbiology and Biotechnology
• /
• v.29 no.7
• /
• pp.1009-1013
• /
• 2019

Polymeric nanoparticles are widely used for drug delivery due to their biodegradability property. Among the wide array of polymers, chitosan has received growing interest among researchers. It was widely used as a vehicle in polymeric nanoparticles for drug targeting. This review explored the current research on the antimicrobial activity of chitosan nanoparticles (ChNP) and the impact on the clinical applications. The antimicrobial activities of ChNP were widely reported against bacteria, fungi, yeasts and algae, in both in vivo and in vitro studies. For pharmaceutical applications, ChNP were used as antimicrobial coating for promoting wound healing, preventing infections and combating the rise of infectious disease. Besides, ChNP also exhibited significant inhibitory activities on foodborne microorganisms, particularly on fruits and vegetables. It is noteworthy that ChNP can be also applied to deliver antimicrobial drugs, which further enhance the efficiency and stability of the antimicrobial agent. The present review addresses the potential antimicrobial applications of ChNP from these few aspects.

• Journal of Adhesion and Interface
• /
• v.20 no.2
• /
• pp.71-75
• /
• 2019

Tannic acid is one of the most commonly found polyphenols in the vegetable field. Initially, research on tannins concentrated on physiological functions such as antioxidants. Recently, however, tannic acid has attracted much interest as a molecular glue as it has been found to interact virtually all bio-macromolecules such as proteins and DNA. The various properties of tannic acid are expected to control the wettability of the surface, contribute to energy storage and generation, and show potential as a medical agent. Here, tannic acid will be discussed about the interaction of with bio-macromolecules as a molecular glue, surface modification, and utilization of itself as biomaterials.