• Structural Engineering and Mechanics
• /
• v.82 no.2
• /
• pp.163-172
• /
• 2022

Zinc-rich epoxy (ZRE) is used to overcome corrosion problems in reinforced concrete (RC) beams and coat steel rebars to protect them from humidity and chlorides. An extra coating layer of Sikadur-31 epoxy (SDE) is utilised to increase bond strength because the use of ZRE reduces the bond strength between concrete and steel rebars. However, the low melting point of SDE indicates that concrete specimens are vulnerable to fire. An experimental investigation on flexural performance of RC beams incorporating ZRE-SDE coating of steel rebars that were destroyed by fire is performed in this study. Twenty beams of five concrete mixes with different cementitious contents were tested to compare fire exposure for coated and uncoated rebars of the same beams at room temperature and determine the optimal cementitious content. Scanning electron microscopy (SEM) was also applied to investigate characteristics of fired mixture samples. Results showed that the use of SDE-ZRE at room temperature improves flexural strengths of the five mixes compared with uncoated rebars with percentages ranging from 8.5% to 12.3%. All beams with SDE-ZRE lost approximately 50% of their flexural strength due to firing. Moreover, the mix incorporating SF (silica fume) of 15% and cement content of 400 kg/m³ introduces optimum behaviour compared with other mixes. All results were supported and verified by the SEM analysis and compressive strength of cubic specimens of the same mixes.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.138-140
• /
• 2008

현재 현수막의 코팅에서 기능을 부여하는 수요가 늘고 있다. 본 실험에서는 코팅제의 유기용제 사용으로 인한 환경오염 문제및 폐기물 처리비용 부담을 줄이기 위하여 수성코팅제를 개발하려한다. acryl binder, 탄산칼슘, silica, 유화제등을 혼합한 코팅제를 knife coating한 후 170$^{\circ}C$로 1분 30초간 열처리 하였다. 이때 acryl binder의 첨가비율은 35${\sim}$55%로 변화를 주었다. 처리한 폴리에스테르에 DTP printing을 한 후 CCM 측정, 내수성, 접착성을 알아본 결과 acryl binder의 첨가비율은 45%일때 가장 우수한 발색성 및 printing 특성을 나타내었다. 기존 수성코팅제에 대비 20${\sim}$30% 발색성이 개선되었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.137-137
• /
• 2010

This research proposed an advanced Electronic bead (EB) using MMA (Methy methacrylate) and CCA (Charge Control Agent). In the first, this paper presents about measurement method and characterization analysis of EB with wet coating method. Furthermore, this work presents the positive and negative EB fabrication procedure. As the experimental results, the proposed EB with charge to ratio[Q/M] is very attractive to Electronic paper driving characterization.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.23 no.2
• /
• pp.58-69
• /
• 2014

In case of esthetic restorative procedure with zirconia restoration, we have to use resin cement because of not only just for retention but also esthetic reason. In such a clinical situation, we have to consider two bonding interfaces, one is tooth surface to resin cement and the other is zirconia surface to resin cement. There is well established bonding protocol between tooth surface to resin cement, but bonding protocol of zirconia surface to resin cement is still controversial. In scientific point of view, there are two mechanism for bonding of zirconia restoration.. One is mechanical retention and the other is chemical adhesion. However, we have three different options for bonding of zirconia restoration in clinical situation; 1) Tribo-chemical coating with silica and silane coupling agent 2) Zirconia primer with phosphate chemistry 3) Self-adhesive resin cement with phosphate chemistry.

• Journal of the Korean Ceramic Society
• /
• v.31 no.5
• /
• pp.499-504
• /
• 1994

PbTiO3 thin films were prepared by sol-gel spin coating method using metal alkoxide and diethanolamine (DEA). The precipitation of the PbTiO3 sol occurred at pH 7.3 with HNO3 addition, regardless of the amount of DEA. The gelation time of the PbTiO3 sol was reduced with increasing amount of HNO3 and/or water. When the PbTiO3 films prepared by 0.2 molar coating solution were annealed at $650^{\circ}C$ for 30 min, dense and single phase perovskite films were obtained. Dielectric constant and loss tangent of the film were 239 and 0.01 at 1 kHz, respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.828-830
• /
• 2002

In this study, we have investigated a simple process of preparation of white pigment particles by physical coating with functionalized wax for the electrophoretic display. We will discuss, especially, the implementation of bistable pigment providing high mobility by using unique charge control agent and also optical properties of wax coated $TiO_2$ particles.

• Applied Science and Convergence Technology
• /
• v.24 no.6
• /
• pp.219-223
• /
• 2015

Enhancement of the surface hydrophobicity of polydimethylsiloxane (PDMS) thin films deposited on substrates covered with titanium dioxide ($TiO_2$) nanospheres was studied. First, a low-temperature solution-phase method using polyvinylpyrrolidone (PVP) as a surface capping agent and a water/dimethylformamide (DMF) mixture as the reaction medium was used to synthesize monodisperse $TiO_2$ nanospheres. It was possible to easily control hydrolysis rate of the Ti-precursors and the size of the synthesized nanospheres by varying the amount of PVP and the volume ratio of the solvent mixture. Spray coating of the synthesized $TiO_2$ nanospheres under the PDMS film increased the water contact angle of the film surface to $150.3^{\circ}$. This simple treatment can modify the surface morphology at a nanometer scale without any long or complicated nanoprocess; hence, the surface enters the superhydrophobic Cassie-Baxter regime.

• Journal of Information Display
• /
• v.8 no.1
• /
• pp.14-17
• /
• 2007

The toner type paper-like display (PLD) has been developed with two polymer particles having opposite polarity composed of polymer, colorant and external additives (nano-sized silica). Nano-sized silica with triboelectric charge was used for the charge control agent (CCA) and influenced on the electrostatic properties of the silica-coated polymer particles. The surface morphology and the cohesiveness of silica-coated polymer particles were changed with the silica coating time. From these results, it was verified that the PLD cell using silica-coated particles (200 seconds) shows a good white appearance and low driving voltage.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.127-132
• /
• 1996

촉매탑에서 수소와 물사이의 수소 동위원소 교환 반응에 의한 중수 분리 및 삼중수소 제거를 위한 소수성 촉매집합체 제조기술을 개발하기 위하여 소수성 촉매집합체 제조 특성에 대하여 연구하였다. 본 연구에서 먼저 일반적인 함침법 및 colloidal method 의하여 각각 백금을 activated carbon에 담지시켜 Pt/Carbon 촉매를 제조하고, 수소 흡착법에 의하여 촉매의 백금 분산도를 비교 분석하였다. 제조된 Pt/Carbon 촉매를 Wanke등의 방법에 따라 소수성 teflon 수지를 binding agent로 사용하여 ceramic bell-saddle 및 육면체형 packing등의 충전물 표면에 coating시켜 촉매 집합체를 제조하고 소결 온도, 충전물의 형태 및 표면 부위에 따른 surface coating 특성에 대하여 연구하였다.

• Journal of Powder Materials
• /
• v.8 no.4
• /
• pp.253-257
• /
• 2001

The effects of mechanical alloying conditions on the formation of Mn-sulfide powders were analyzed. Impeller rotating speed, lubricant coating and added amounts of process control agent(stearic acid) were selected as a process control factor. MnS compounds are synthesized in 3 hours by mechanical alloying at the alternative milling condition. Discontinuous rotating speed of 1200rpm for 4 minutes and 1000rpm for 1 minute shows more effects on the compound formation of MnS. After coating of lubricant on the wall, elementary Mn and sulfur were partially remained by mechanical alloying. The friction effects of the wall and grinding media on the powders are significantly important to form the compound of MnS.