• 제목/요약/키워드: CoTi

검색결과 1,684건 처리시간 0.03초

기계적 합금화 공정으로 제조된 Fe-14Cr Ferritic 산화물 분산 강화(ODS) 합금 강의 고온 산화 거동 (High Temperature Oxidation Behavior of Fe-14Cr Ferritic Oxide Dispersion Strengthened Steels Manufactured by Mechanical Alloying Process)

  • 김영균;박종관;김휘준;공만식;이기안
    • 한국분말재료학회지
    • /
    • 제24권2호
    • /
    • pp.133-140
    • /
    • 2017
  • This study investigates the oxidation properties of Fe-14Cr ferritic oxide-dispersion-strengthened (ODS) steel at various high temperatures (900, 1000, and $1100^{\circ}C$ for 24 h). The initial microstructure shows that no clear structural change occurs even under high-temperature heat treatment, and the average measured grain size is 0.4 and $1.1{\mu}m$ for the as-fabricated and heat-treated specimens, respectively. Y-Ti-O nanoclusters 10-50 nm in size are observed. High-temperature oxidation results show that the weight increases by 0.27 and $0.29mg/cm^2$ for the as-fabricated and heat-treated ($900^{\circ}C$) specimens, and by 0.47 and $0.50mg/cm^2$ for the as-fabricated and heat-treated ($1000^{\circ}C$) specimens, respectively. Further, after 24 h oxidation tests, the weight increases by 56.50 and $100.60mg/cm^2$ for the as-fabricated and heat-treated ($1100^{\circ}C$) specimens, respectively; the latter increase is approximately 100 times higher than that at $1000^{\circ}C$. Observation of the surface after the oxidation test shows that $Cr_2O_3$ is the main oxide on a specimen tested at $1000^{\circ}C$, whereas $Fe_2O_3$ and $Fe_3O_4$ phases also form on a specimen tested at $1100^{\circ}C$, where the weight increases rapidly. The high-temperature oxidation behavior of Fe-14Cr ODS steel is confirmed to be dominated by changes in the $Cr_2O_3$ layer and generation of Fe-based oxides through evaporation.

경남 밀양지역 납석광상과 안산암질 모암의 지구화학적 연구 (A Geochemical Study on Pyrophyllite Deposits and Andesitic Wall-Rocks in the Milyang Area, Kyeongnam Province)

  • 오대균;전효택;민경원
    • 자원환경지질
    • /
    • 제25권1호
    • /
    • pp.27-39
    • /
    • 1992
  • Several pyrophyllite deposits occur around the Milyang area where Cretaceous andesitic rocks and spatially related granitic rocks are widely distributed. Pyrophyllite ores consist mainly of pyrophyllite, and quartz with small amount of sericite, pyrite, dumortierite, and diaspore. The andesitic rocks and spatially related granitic rocks in this area suggest that they could be formed from the same series of a calc-alkaline magma series. The contents of $SiO_2$, $Al_2O_3$, LOI(loss on ignition) are enriched, and $K_2O$, $Na_2O$, CaO, MgO, $Fe_2O_3$ are depleted in altered andesitic rocks and ores. Enrichment of As, Cr, Sr, V, Sb and depletion of Ba, Cs, Ni, Rb, U, Y, Co, Sc, Zn are characteristic during mineralization. The pyrophyllite ores can be discriminated from the altered-and unaltered wall-rocks by an increasing of $(La/Lu)_{cn}$ from 4.18~22.13 to 8.98~55.05. In R-mode cluster analysis, Yb-Lu-Y, La-Ce-Hf-Th-U-Zr, $TiO_2-V-Al_2O_3$, Sm-Eu, $CaO-Na_2O-MnO$, Cu-Zn-Ag, $K_2O-Rb$ are closely correlated. In the discriminant analysis of multi-element data, $P_2O_5$, As, Cr and $Fe_2O_3$, Sr are helpful to identify the ores from the unaltered-and altered wall-rocks. In the factor analysis, the factors of alteration of andesitic rocks and ore mineralization were extracted. In the change of ions per unit volume, $SiO_2$, $Al^{3+}$ and LOI are enriched and $Na^+$, $K^+$, $Ca^{2+}$, $Mg^{2+}$, $Mn^{2+}$ and $Fe^{3+}$ are depleted during the alteration processes. The Milyang and the Sungjin pyrophyllite deposits could be mineralized by hydrothermal alteration in a geochemical condition of low activity ratio of alkaline ions to hydrogen ion with reference to spatially related granitic rocks.

  • PDF

치과용 임플랜트에서 지대주 나사의 길이 및 반복 조임 횟수가 지대주 나사의 풀림에 미치는 영향 (THE INFLUENCE OF ABUTMENT SCREW LENGTH AND REPEATED TIGHTENING ON SCREW LOOSENING IN DENIAL IMPLANT)

  • 최진호;양재호;조원표;이재봉
    • 대한치과보철학회지
    • /
    • 제44권4호
    • /
    • pp.432-442
    • /
    • 2006
  • Statement of problem: One of common problems associated with dental implant is the loosening of abutment screws that retain the implants. Purpose : This study was performed to investigate the influence of abutment screw length and repeated tightening on screw loosening in dental implant. Material and method: Forty nine Hexplants (13mm length, 4.3mm diameter, Ti grade IV, Warantec. Co. Ltd. Seongnam, Korea) and cementation type abutments(straight abutment) and abutment screws (0.4mm/pitch) were divided into 7 groups, depending on abutment screw length. Each implant and abutment was tightened to 30Ncm by torque controller(MGT50, MARK-10 Inc., USA) and the removal torque values were measured during 10 consecutive closure/opening trials. Results and Conclusion: The results of comparing the removal torque value are as follows : 1. There is no significant difference in the removal torque value between groups in 10 consecutive closure/opening trials (p = 0.97). 2. If the fractured abutment screw is engaged in longer than 2.425 thread length, there is no significant difference in the preload between the fractured abutment screw and the new abutment screw when both are equally tightened to 30 Ncm. 3. The removal torque value in the 1st trial(24.510 Ncm) was lower than that in the 2nd, 3rd, 4th, 5th, 6th, 7th trials and the removal torque value in the 2nd trials(25.551 Ncm) was maximum and was decreased in 1311owing trials. The removal torque value in the 1st trial was significantly lower than that in the 2nd, 3rd, 4th trials and was significantly higher than that in the 8th, 9th, l0th trials(p<0.05). 4. In the 2nd, 3rd, 4th, 5th, 6th, 7th trials, the abutment screw was mainly influenced by settling effect and the higher preload was obtained In the 8th, 9th, l0th trials, the abutment screw was mainly influenced by adhesive wear and the progressively lower preload was obtained.

Continuous wave of obturation technique에서 플러거의 다양한 적용 깊이에 따른 근단부 폐쇄효율 비교 (COMPARISON OF APICAL SEALING EFFICACIES USING DIFFERENT PLUGGING DEPTH IN CONTINUOUS WAVE OF OBTURATION TECHNIQUE)

  • 이상진;박정길;허복;김현철
    • Restorative Dentistry and Endodontics
    • /
    • 제32권6호
    • /
    • pp.491-497
    • /
    • 2007
  • 이 연구의 목적은 continuous wave of obturation technique으로 근관 충전을 할 때, 다양한 heat source plugger의 깊이에 따른 근단부 근관 폐쇄능력을 비교하는 것이었다. 직선 형태 발거 소구치를 #35/.06 크기까지 니켈티타늄 파일을 사용하여 성형 및 세정하였다. 성형과 세정이 완료된 치아를 heat source plugger의 적용 깊이에 따라 15개씩 5군으로 분류하였다. 3 mm, 4 mm, 5 mm, 6 mm, 7 mm, 양성 대조군을 제외한 모든 근관은 E&Q plus(Meta Biomed Co., Chungju, Korea)를 사용하여 #35/.06 gutta-percha cone으로 충전하였다. 모든 치아의 근첨공 주변 1 mm를 제외하고 nail varnish를 도포하였고 음성 대조군은 근첨공을 포함하여 전체 면을 도포하였다. 모든 시편을 1% 메틸렌블루 용액에 72시간 동안 보관한 다음 치근첨으로부터 1, 2, 3 mm 높이에서 수평으로 절단하였다. 각 단면을 $12.5{\times}2.5$배 현미경하에서 관찰하고 디지털 카메라로 촬영하였다. 염색제 누출 평가를 위해 aye-degree scoring system을 사용하였다. 각 절단면에서의 점수를 모두 합하여 한 시편의 점수로 사용하고 통계학적 분석을 하였다. 이 실험 조건하에서, 3-7 mm까지의 heat source plugger의 적용 깊이는 근단부 폐쇄에서 유의한 차이를 나타내지 않았다. 5-7 mm의 Buchanan's protocol을 포함한 3-7 mm를 모두 임상 적용에서 받아들여질 만하다고 보인다.

이동형 차량용 무인사격시스템의 외란 제거 및 자세 제어 (Disturbance Rejection and Attitude Control of the Unmanned Firing System of the Mobile Vehicle)

  • 장유신;계중읍
    • 전자공학회논문지SC
    • /
    • 제44권3호
    • /
    • pp.64-69
    • /
    • 2007
  • 시스템의 자세 제어는 사용되는 모터의 위치 제어로 대응되며, 이러한 시스템은 운용환경 시에 충격 진동이 발생하게 된다. 이러한 충격 진동 외란을 제거해야 요구하는 위치 제어를 수행할 수 있다. 로봇 제어 분야에서 불확실한 외란에 의한 로봇의 자세 제어는 가장 기본적이면서 중요한 분야중의 하나이다. 이러한 문제를 다루기 위하여 계산 토크 방식에 기초한 선형 제어기법이나 적응 제어 기법, 강인 제어 기법 등을 이용한 연구 결과들이 발표되고 있다. 그러나 그러한 기법은 일반적으로 로봇의 정확한 동력학적 특성을 알아야 하며, 구현하기가 복잡하다. 따라서 본 논문에서는 적응 규칙에 의하여 모델의 불확실성, 시스템의 변화, 외란으로 인해 발생하는 공칭 플랜트와의 오차를 보상하도록 제어 입력을 생성하는 내부 루프 부분과 공칭 플랜트 모델의 명령을 추종하도록 하여 제어 입력을 생성하는 외부 루프 부분으로 구성되는 방법인 외란관측기(Disturbance OBserver : DOB) 제어 알고리즘을 제안한다. 또한 프로세서의 신뢰성과 수치 연산 및 알고리즘의 빠른 처리를 위해 현재 사용 빈도가 높은 TI사의 DSP시리즈 중에서 부동 소수점 연산 기능을 가지면서 모터 제어에 적합한 TMS320C2000계열의 TMS320F2812을 사용하여, 운용 시 발생되는 진동 등에 대한 외란 제거를 목적으로 한다. 본 논문은 규명된 시스템 모델식을 바탕으로 DOB 제어 시뮬레이션을 수행하고 시뮬레이션으로 검증된 DOB 모터 자세 제어 알고리즘을 DSP에 적용하기 위해 코드변환하고 PMSM 모터 모델 시뮬링크 블록을 구성하여 외란 관측기 제어 알고리즘을 모터 실험 시스템에 적용함으로써 타당성을 검증하고 상용 제어기로 실제 현장에 적용 가능함을 입증한다.

환원처리가 Ba-ferrite의 물성에 미치는 영향 (The Effect of Hydrogen Reduction Treatment on Properties of Ba-ferrite)

  • 홍양기;정홍식;김현준
    • 한국자기학회지
    • /
    • 제7권1호
    • /
    • pp.25-30
    • /
    • 1997
  • 치환형 Ba-ferrite의 수소환원 거동은 순수한 Ba-ferrite와는 다르게 나타났다. 환원온도 250 .deg. C에서 520 .deg. C의 범위에서 치환형 Ba-ferrite의 보자력은 증가하다가 다시 감소하는 반면에 순수한 Ba-ferrite는 계속 감소 하였다. 치환형 Ba-ferrite의 환원과정은 환원되는 정도에 따라 3단계로 나뉘어진다. 1과 2단계에서 Ba-ferrite의 구조는 그대로 유지를 하지만 자기적 성질은 다르게 나타났다. 1단계에서 보자력은 증가하고 산화처리시 가역적이지만, 2단계에서는 보자력이 더욱 증가하고 산화처리시 비가역적이었다. 그러나 3단계에서는 Ba-ferrite 구조 자체가 붕괴되어 .alpha. -Fe와 소량의 BaFe $O_{3-x}$의 생성으로 $H_{c}$는 크게 감소하고 포화자화값은 130 emu/g으로 크게 증가하였다. 이 때 보자력 분포도는 크게 넓어지며 입자크기도 감소하였다. 또한 치환이온들은 환원과정에서 Ba-ferrite 구조의 붕괴를 억제하였으며, 2a + 4 $f_{IV}$ , 2b 및 12k 자리의 치환이온들이 4 $f_{VI}$ 와 12k'의 자리로 이동함을 확인하였다. 따라서 1과 2단계에서의 보자력 증가원인은 치환이온의 자리이동에 따른 고보자력 상의 생성 때문이었다.

  • PDF

고속 태그 수집을 위한 개선된 능동형 RFID 시스템용 프레임 Slotted ALOHA 알고리즘 구현 (Implementation of Improved Frame Slotted ALOHA Algorithm for Fast Tag Collection in an Active RFID System)

  • 김지태;강병권;이강원
    • 한국통신학회논문지
    • /
    • 제39B권9호
    • /
    • pp.598-605
    • /
    • 2014
  • 본 논문에서는 능동형 RFID 시스템용 고속 태그 수집을 위한 개선된 알로하 알고리즘을 제안하고, 이를 TI사의 CC2530 칩을 사용하여 태그와 리더기 각각의 기능을 구현하여 시험함으로써 그 성능을 증명하였다. 기존의 ISO/IEC 18000-7 등의 능동형 RFID 규격에서 제시하고 있는 태그 수집 알고리즘에서는 리더기와 태그의 통신이 성공적으로 종료된 후 리더기가 각 태그들에게 별도의 슬립 명령을 전송하는 반면, 제안된 방식에서는 통신이 종료된 태그들은 두 번째 명령어를 확인한 후 즉시 슬립 모드로 진행할 수 있도록 함으로써 리더기의 태그 수집 시간을 대폭 감소시켰다. 리더기와 태그를 구현하여 시험한 결과 30개의 태그가 평균 400 ms 이내에서 모두 인식되었으며, 1초 이내에 인식되는 인식률은 99.7% 이상임을 확인하였다. 리더기와 태그 간의 거리가 2m 이내인 경우 태그는 100% 인식되었으며, 2.5m 이내인 경우와 3m 이내인 경우 초당 인식 확률이 각각 99.94%와 99.7%였다. 각 거리의 경우를 평균하여 99.91%로 나타남으로써 실제 현장에의 적용 가능성을 보였다.

제2형 근관의 확대에 따른 최종근관장파일 크기의 비교 (A COMPARISON OF MASTER APICAL FILE SIZE ACCORDING TO INSTRUMENTATION IN TYPE II ROOT CANAL)

  • 정은주;이동균;백신영;황호길
    • Restorative Dentistry and Endodontics
    • /
    • 제33권5호
    • /
    • pp.435-442
    • /
    • 2008
  • 제2형의 근관형태를 갖는 치아에서 각각의 근관을 모두 근관장까지 확대한 경우, 여러 확대기구에 따른 최종근관장파일의 크기를 상호 비교하여 얼마나 많은 변화가 있었는지를 분석하고자 치근 우식이 없고 치근단공 형성이 완료되었으며 2개의 근관 입구에서 시작하여 하나의 치근단공을 갖는 제 2형의 근관형태를 보이는 상악 소구치, 상악 대구치의 근심협측 치근 및 하악 대구치의 근심 치근을 선택하여 확대기구에 따라 KF군, PT군, HS군, K3군으로 분류하고 치경부 조기 확대를 시행하였다. 초기근관장파일이 15번 크기인 치아를 각 군당 20개씩 무작위로 선택하였고, 모든 근관을 각 군에 해당되는 30번 크기의 파일까지 제조회사의 지시에 따라 확대를 시행한 후, 촉감과 universal testing machine을 이용하여 최종근관장파일의 크기를 결정하였다. 각 군의 최종근관장파일의 크기와 제거 시 요구되는 힘의 크기에 대한 유의성 검증은 one-way ANOVA를 이용하여 비교 분석하였으며, 사후검정은 Tukey HSD test를 이용하여 0.05의 유의수준에서 분석하였다. 본 연구의 결과 제2형의 근관형태를 갖는 치아의 근관확대 시, 모든 근관을 각각의 근관장으로 확대하는 방법은 확대에 마지막으로 이용된 기구의 크기보다 한, 두 단계 정도 증가된 최종근관장파일을 나타냈다. 그러므로 제2형 근관형태를 나타내는 치아의 근관치료 시 임상가들은 근관충전에 앞서 치근단 받침을 다시 확인하고 형성하는 과정이 필요하리라 사료된다.

IDT 전극 패턴 임베디드 압전 에너지 하베스터의 특성 (Energy Harvesting Characteristics of Interdigitated (IDT) Electrode Pattern Embedded Piezoelectric Energy Harvester)

  • 이민선;김창일;윤지선;박운익;홍연우;백종후;조정호;박용호;장용호;최범진;정영훈
    • 한국전기전자재료학회논문지
    • /
    • 제29권9호
    • /
    • pp.581-588
    • /
    • 2016
  • Piezoelectric thick films of a soft $Pb(Zr,Ti)O_3$ (PZT) based commercial material were produced by a conventional tape casting method. Thereafter, the interdigitated (IDT) Ag-Pd electrode pattern was printed on the $25{\mu}m$ thick piezoelectric film at room temperature. Co-firing of the 10-layer laminated piezoelectric thick films was conducted at $1,100^{\circ}C$ and $1,150^{\circ}C$ for 1 h, respectively. Piezoelectric cantilever energy harvesters were successfully fabricated using the IDT electrode pattern embedded piezoelectric laminates for 3-3 operation mode. Their energy harvesting characteristics were investigated with an excitation of 120 Hz and 1 g under various resistive loads (ranging from $10k{\Omega}$ to $200k{\Omega}$). A parabolic increase of voltage and a linear decrease of current were shown with an increase of resistive load for all the energy harvesters. In particular, a high output power of 3.64 mW at $100k{\Omega}$ was obtained from the energy harvester (sintered at $1,150^{\circ}C$).

$\textrm{Fe}_{80-x}\textrm{P}_{10}\textrm{C}_{6}\textrm{B}_{4}\textrm{M}_{x}$(M=Transition Metal) 비정질합금의 열적안정성 (Thermal Stability of $\textrm{Fe}_{80-x}\textrm{P}_{10}\textrm{C}_{6}\textrm{B}_{4}\textrm{M}_{x}$(M=Transition Metal) Amorphous Alloys)

  • 국진선;전우용;진영철;김상협
    • 한국재료학회지
    • /
    • 제7권3호
    • /
    • pp.218-223
    • /
    • 1997
  • 과냉각액체구역(${\Delta}T_{x}=T_{x}-T_{g}$)을 갖는 $Fe_{80}P_{10}C_{6}B_{4}$ 조성에 천이금속(Ti, Zr, Hf, V, Nb, Ta, Cr, Mo, W, Mn, Co, Ni, Pd, Pt및 Cu)를 첨가하여 이들 원소가 유리화온도($T_{g}$), 결정화온도($T_{x}$) 및 과냉액체구역 (${\Delta}T_{x}$)에 미치는 영향에 \ulcorner여 조사하였다. $Fe_{80}P_{10}C_{6}B_{4}$ 합금의 ${\Delta}T_{x}$ 값은 27K였으나 이 합금에 Hf, Ta 및 Mo을 각각 4at%첨가하면 그 값이 40k 이상으로 증가하였다. 이같은 ${\Delta}T_{x}$ 값의 증가는 유리화온도($T_{g}$의 상승보다 결정화온도($T_{x}$)의 상승폭이 크기 때문이다. $T_{g}$$T_{x}$는 외각전자밀도(e/a)가 약 7.38에서 7.05로 감소할수록 상승하였다. e/a의 감소는 천이금속과 다른 구성원소(반금속)사이의 상호결합상태를 의미한다. 즉 $T_{g}$$T_{x}$의 상승은 강한 상호결합력에 기인하는 것으로 사료된다.

  • PDF