• Journal of Magnetics
• /
• v.3 no.4
• /
• pp.123-126
• /
• 1998

The magneto-impedance (MI) has been measured in the annealed Co66Fe4Ni1B14Si15 amorphous ribbon for the evaluation of anisotropy field. MI at the frequency of 10 MHz is related to the transverse permeability from rotational magnetization depending on the local anisotropy field. MI varies sensitively with the annealing temperature, reflecting the change of anisotropy field distribution. The local anisotropy fields evaluated from MI Profiles are discussed in terms of the magnetic softness and microstructural change by the annealing.

• Journal of Magnetics
• /
• v.2 no.3
• /
• pp.72-75
• /
• 1997

The temperature dependent saturation magnetization curve of amorphous Fe67 Co18B14Si1, alloy was measured using a SQUID magnetometer and vibrating sample magnetometer from 5 K up to 800 K. Inelastic neutron neutron scattering measurements also have been used to study the long wavelength spin dynamics of this high Tc amorphous ferromagnetic alloy. The magnon dispersion curve exhibit the conventional quadratic relationship E = D (T) q2 + $\Delta$, typical of an iso=obtained from a low temperature magnetization curve, which was consistent with the value obtained from the analysis oif inelastic neutron scattering data after consideration of its temperature dependence.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.225-229
• /
• 2013

We report a measurement for the anomalous Nernst effects induced by a temperature gradient in [CoSiB/Pt] multilayer films with perpendicular magnetic anisotropy. The Nernst voltage shows a characteristic hysteresis which reflects the magnetization of the film as in the case of the anomalous Hall effects. With a local heating geometry, we also measure the dependence of the anomalous Nernst voltage on the distance d from the heating element. It is roughly proportional to $1/d^{1.3}$, which can be conjectured from the expected temperature gradient along the sample from the heat equation.

• Journal of Powder Materials
• /
• v.25 no.5
• /
• pp.375-378
• /
• 2018

Conductive and dielectric SiC are fabricated using electroless plating of Ni-Fe films on SiC chopped fibers to obtain lightweight and high-strength microwave absorbers. The electroless plating of Ni-Fe films is achieved using a two-step process of surface sensitizing and metal plating. The complex permeability and permittivity are measured for the composite specimens with the metalized SiC chopped fibers dispersed in a silicone rubber matrix. The original non-coated SiC fibers exhibit considerable dielectric losses. The complex permeability spectrum does not change significantly with the Ni-Fe coating. Moreover, dielectric constant is sensitively increased with Ni-Fe coating, owing to the increase of the space charge polarization. The improvements in absorption capability (lower reflection loss and small matching thickness) are evident with Ni-Fe coating on SiC fibers. For the composite SiC fibers coated with Ni-Fe thin films, a -35 dB reflection loss is predicted at 7.6 GHz with a matching thickness of 4 mm.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.8
• /
• pp.2341-2344
• /
• 2010

A convenient synthesis of substituted [1,2,4]-triazolo [1',2':1,2]pyrimido[6,5-b]-quinoline 4(a-i) from substituted 2-chloroquinoline-3-carbaldehyde 1(a-i) and 4H-1,2,4-triazol-3-amine 2 by using $SiO_2/K_2CO_3$ under microwave irradiation. This method affords the [1,2,4]-Triazolo [1',2':1,2]pyrimido[6,5-b]-quinoline 4(a-i) under the influence of microwave irradiation in solvent-free conditions within short span (12 - 20 min), & gaves excellent yields (89 - 95%). All the synthesized compounds were further screened for their antibacterial activities. Some of our compounds showed excellent antibacterial activities against control drugs.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.324-326
• /
• 1997

Low power ZnO-Si gas sensor below 500 mW at operating temperature has been fabricated by using micromachining technique. I-V measurement shows the power consumption of 260 mW at $400^{\circ}C$ The sensitivity of the sensor was 45 percent at operating temperature of $350^{\circ}C$(230 mW) with 1,000 ppm CO gas atmosphere. The response and the recovery time found out to be 94 sec and 180 sec, respectively, when CO gas was used. In order to measure the exact temperature of the gas sensing layer, Pt/Cr bilayer-RTD was used in this experiment.

• 한국전자현미경학회:학술대회논문집
• /
• 1997.05a
• /
• pp.47-48
• /
• 1997

• Proceedings of the Korean Magnestics Society Conference
• /
• 2015.05a
• /
• pp.150-150
• /
• 2015

• Proceedings of the Korean Magnestics Society Conference
• /
• 2015.05a
• /
• pp.121-122
• /
• 2015

• Proceedings of the Korean Magnestics Society Conference
• /
• 2010.06a
• /
• pp.90-91
• /
• 2010