• Proceedings of the Korean Magnestics Society Conference
• /
• 1999.10a
• /
• pp.110-111
• /
• 1999

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2001.05a
• /
• pp.236-237
• /
• 2001

In this study, experiments were carried out to measure the variations in the corrosion potential and current density of polarization curves with amorphous $Fe_{70}Cr_5Si_{10}B_{15}$ and $Co_{70}Cr_5Si_{10}B_{15}$ alloy ribbon. The results were particularly examined to identify the influences of corrosion potential including various conditions such as hydrochloric acid, temperature, salt, pH, and oxygen. The optimum conditions were established with variations including temperature, salt, pH, oxygen, corrosion rate, and resistance of corrosion potential. The mass tranfer coefficient(${\alpha}$) value was determined with the Tafel's slope for the anodic dissolution based on the polarization effect with optimum conditions. The second anodic current density peak and maximum passive current density were designated as the critical corrosion sensitivity($I_{r}/I_{f}$).

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.255-260
• /
• 1998

Fabrication condition and magnetic properties of ultrathin Co-based amorphous alloy have been investigated. When the ejection gas pressure was lower than 0.05 kgf/$\textrm{cm}^2$ at the roll speed of 55 m/s, ultrathin ribbons with the thickness less than 10 ${\mu}{\textrm}{m}$ were successfully obtained. The ribbon thickness decreased linearly with the decrease in ejection pressure. Moreover the significant decrease in ribbon width was accompanied with the decrease of thickness in the range of ejection pressure to form an ultrathin ribbon. This behavior was attributed to the decrease of effective ejection pressure in the both end-sides of rectangular nozzle due to the larger friction between molten metal and nozzle wall. The effective permeability at low frequency (1 kHz) decreased largely with the decrease in ribbon thickness, while the coercive force increased with the thickness decrease. It was considered that these behaviors were due to the enhancement of surface effect leading to the suppression of wall motion. However effective permeability at high frequency (1 MHz) increased with the decrease in ribbon thickness, and this was ascribed to the easier magnetization rotation owing to the reduction of eddy current.

• Journal of Magnetics
• /
• v.6 no.3
• /
• pp.86-89
• /
• 2001

Microstructure modifications are investigated for annealed Co-based amorphous ribbon in vacuum and open air. X-ray diffraction (XRD) spectra for annealed sample in vacuum indicate atomic arrangements with initial nucleation of hcp-Co crystallite at 38$0^{\circ}C$ annealing temperature. However, the XRD spectra in samples with long annealing times of $t_a\geq300$ min demonstrate sharp and good developed surface crystalline hcp-, fcc- Co and $Co_2$Si phases. The giant magnetoimpedance (GMI) profile at 0.1 MHz displaying one-peak behavior in vacuum annealed samples at T = 38$0^{\circ}C$ irrespective of annealing time $t_a$ from 20 to 480 mim. For the annealed samples in an open air, the GMI profile shows two-peaks for $t_a$ = 20 min annealed sample. However, one of peaks disappears and an asymmetric GMI profile exhibits a drastic step-like change near zero field for $t_a\geq300$min. Such asymmetric GMI characteristics is related to the surface microstructures of fcc-Co, hop-Co and $Co_2$Si crystalline phases.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2004.12a
• /
• pp.89-90
• /
• 2004

• Journal of Magnetics
• /
• v.2 no.4
• /
• pp.130-134
• /
• 1997

The amorphous Co-based alloy Co66Fe4Ni1B15Si14 (Metglas 2714A) is a suitable magnetic core material for high frequency operation. Appreciable reduction of the coercive force can be achieved by proper heat treatment. In this study, samples annealed at wide temperature range were analyzed using differential scanning calorimetry, high frequency B-H loop tester, X-ray diffractometer and resistivity meter. The results show that coercive force at 10 kHz decreases with in-creasing annealing temperature up to 773 K, but dramatically increases above this temperature. The squareness shows that the magnetic anisotropy on longitudinal direction of the as-cast state remains up to 773 K. Above this temperature, it decreases down to 0.5 that represents random distribution of magnetic domains. The crystallization abruptly occurs between 781 K and 783 K.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.149-151
• /
• 1994

This thesis describes the effect of heat treatment on the magnetic properties of Co-bsaed Amorphous. A sample was chosen as basic composition with Co$\_$82//Si$\_$2//B$\_$16/ of zero magnetostriction. It was made by single roll method with quartz orifice 0.5[mmø], Ar gas pressure 0.6 [kg/cm$^2$] and roll speed 28 (m/sec) and atmosphere is ,Ar gas. We obtained the sample of width 2.4(mm), thickness 45[$\mu\textrm{m}$]. Made sample annealed for the improvement of magnetic propertics at at annealing temperature 325,350,375 and 400$^{\circ}C$ and annealing time 15, 30, 45, 60 and 120min respectiveily. Amorphous ribbon of co-based showed high permeab- ility ${\mu}$=8000∼14000, and became improvement of magnetic properties according to anneal ins temperature and time. Especially. Amorphous sample at 325$^{\circ}C$ ,45min appearanced high permeability ${\mu}$=13, 589 at frequency f= 100Hz. and loss factor was reduced at low frequency with rising anneal ins ti me and temperature more annealed sample than basic sample.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.7
• /
• pp.621-625
• /
• 1996

A variety of metal oxides were coated by sol-gel process from their metal alkoxides on the ribbons of Co-based and Fe-based amorphous alloys, and the effects of surface oxide coating on the magnetic properties of the alloy are investigated. The core loss is found to be reduced significantly by the oxide coating, the loss reduction becoming more prominent at higher frequencies. The shape of the hystersis loop is also dependent upon the kind of the coated metal oxide. The coatings of MgO, SiO2, MgO·SiO2 and MgO·Al2O3 induce tensile stress into the Fe-based ribbon whereas those of BaO, Al2O3, CaO·Al2O3, SrO·Al2O3 and BaO·Al2O3 induce compressive stress. These results may be explained by the modification of domain structures via magnetoelastic interactions with the shrinkage stress induced by the sol-gel coating.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.272-272
• /
• 2003

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.153.1-153.1
• /
• 2007