• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1895-1897
• /
• 1999

This paper describes the fabrication and performance characterizations of the CIGS$(CuInGaSe_2)$ solar cells and its prototype module. The CIGS cell and module were fabricated on the sodalime glass$(5\times5cm^2)$ by the well known three stage co-evaporation and series connection followed by patterning process. respectively. The developed minimodule with active area of $14.7cm^2$ showed 6.0% solar efficiency($V_{oc}$=3.2V, $I_{sc}$=79.8mA, FF=34.6%) in AM 1.5 condition.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2276-2280
• /
• 2011

An indium-tin-oxide (ITO) is normally used as a substrate in organic photovoltaic cells. We examined the effects of an oxygen ($O_2$) plasma treatment on the electrical properties of an organic photovoltaic cell. Experiments with four-point probe method and atomic force microscope revealed the lowest surface resistance of 17.64 ${\Omega}$/sq and the lowest average surface roughness of 1.39 nm at the plasma treatment power of 250 W. A device structure of ITO/CuPc/$C_{60}$/BCP/$Cs_2CO_3$/Al was fabricated by thermal evaporation with and without the plasma treated ITO substrate. It was found that the power conversion efficiency of the cell with the plasma treated ITO is 65 % higher than the one without the plasma treated ITO.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.427-427
• /
• 2012

Cu(In,Ga)$Se_2 $ (CIGS) 박막 태양전지는 높은 효율과 낮은 생산 단가로 인해 많은 연구가 이루어지고 있다. 특히, Se flux는 박막의 특성에 가장 중요한 CIGS의 결정성, 결정립 크기, 결정방향을 형성하는데 영향을 주는 것으로 알려져 있다. 일반적인 co-evaporation에 사용되는 Se effusion cell의 경우, 높은 분자가를 가지는 Se 분자들이 공급되기 때문에 낮은 반응성을 보이지만 Se cracker cell을 사용할 경우 Se 분자들이 열적으로 크래킹되어 낮은 분자가를 가지므로 화학적으로 높은 반응성을 가진다. 따라서 적은 양의 Se으로도 양질의 CIGS 박막 제작이 가능하다. 본 연구에서는 Se effusion cell과 cracker cell을 이용하여 CIGS 광흡수층을 제작하였으며, 각각 제작된 CIGS 박막의 특성을 비교하였다. 또한 Se cracker cell의 reservoir zone(R-zone) 온도를 통해 Se flux를 변화시켜 Se flux에 따른 CIGS 박막 태양전지의 특성에 대해 알아보았다. SEM, EDS, XRD 측정을 통해 박막의 특성을 분석하였고, J-V 측정을 통해 태양전지의 특성에 대해 알아보았다. Se cracker를 사용하여 제작된 CIGS 박막의 결정립 크기가 effusion cell로 제작된 박막보다 더 크게 나타났고, Se flux가 증가할수록 결정립의 크기는 증가하였다. Se cracker의 flux가 $0.17{\'{{\AA}}}$/s일 때 반사방지막 없이 13.14%의 효율을 나타내었다.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.54-62
• /
• 2012

The main role of surface sizing of linerboard is to improve surface and strength properties. Since surface sizing solution is applied on once dried web, substantial amount of drying energy is required. Saving of the drying energy associated with surface sizing can be made by increasing the solids content of the starch solution in size press. Therefore, it is highly desirable to develop low viscosity starches for surface sizing. A low viscosity oxidized starch was prepared and compared its effect of surface sizing with a conventional oxidised starch. Results showed increase in solids content of the starch solution decreased evaporation energy and drying time. Low viscosity starch penetrated deeper into paper and this improve various mechanical properties of linerboard.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.7-14
• /
• 2002

In order to reduce exhaust omissions of spark ignition engine, it is important not only to improve catalyst conversion efficiency but also to directly reduce engine out exhaust emissions, during cold starting and warm up process. Therefore many researchers have been attracted to develop an early fuel evaporator(EFE) by Introducing a ceramic heater fur a solution of engine out exhaust emissions in SI engine. But, the performance of the EFE in MPI engine to reduce the exhaust emissions and to improve the cold startability has not been clarified yet. The purpose of this study is to evaluate the feasibility of a glow plug far EFE. Impinging spray using heated and unheated glow plug helps the vaporization of the fuel and heat up the three way catalyst sufficiently. The amount of CO, and UHC is reduced overall. The amount of NOx is higher at the initial stage, but become lower as time goes on than without glow plug.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.1
• /
• pp.87-95
• /
• 2018

The high-precision magnetic levitation transport system is a transport device applying the principle of magnetic levitation. So it is preferable for manufactory process of semiconductor and display industries. In this system, the gap sensors are arranged discontinuously and turned on or off when the tray moves in the running direction. Therefore, precise gap data is important for precise control of the carrier. However, a slight error occurs in the process of installing the gap sensor. So, in this paper, we introduce the high-precision magnetic levitation transport system for OLED evaporation process. Also, we propose a strategy for stable flight control and an offset algorithm for tracking installation errors transport system. The performances of the proposed algorithm are validated through simulation.

• Journal of the Korean Applied Science and Technology
• /
• v.2 no.1
• /
• pp.19-23
• /
• 1985

In order to know the quality changes of the fat and oil foods packed in plastics film by the sunlight, we examined the sunlight transmitting rate by the kind of films and measured the acid value and peroxide value according to it. The results obtained were as follows : 1. The sunlight transmitting rate of various films was explained especial permeability under the wavelength of less than 300nm, but it marked a regular form under that of more than 30nm. 2. The vacuum evaporation film with aluminum on the polyester shuts off most of the sunlight, therefore, it has the best effect that keeps the fats and oils off rancidity. 3. The sunlight transmitting rate of the white color printing film drops about 80% as compared with not printing. 4. The preventive power against the rancidity of fats and oils is PET/Al, PET, PE, nylon and OPP film in that order. The changes of peroxide value and acid value were approximately the same as that of the sunlight transmitting rate.

• Korean Journal of Materials Research
• /
• v.16 no.5
• /
• pp.292-296
• /
• 2006

Effects of rapid thermal annealing of bismuth telluride thin films on their thermoelectric properties were investigated. Films with four different compositions were elaborated by co-sputtering of Bi and Te targets. Rapid thermal treatments in range of $300{\sim}400^{\circ}C$ were carried out during 10 minutes under the reducing atmosphere (Ar with 10% $H_2$). As the temperature of thermal treatment increased, carrier concentrations of films decreased while their mobilities increased. These changes were clearly observed for the films close to the stoichiometric composition. Rapid thermal treatment was found to be effective in improving the thermoelectric properties of $Bi_2Te_3$ films. Recrystallization of $Bi_2Te_3$ phase has caused the enhancement of thermoelectric properties, along with the decrease of the carrier concentration. Maximum values of Seebeck coefficient and power factor were obtained for the films treated at $400^{\circ}C$ (about $-128{\mu}V/K$ and $9{\times}10^{-4}\;W/K^2m$, respectively). With further higher temperature ($500^{\circ}C$), thermoelectric properties deteriorated due to the evaporation of Te element and subsequent disruption of film's structure.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.701-706
• /
• 2013

We have focused on the conversion efficiency of CIGS thin film solar cell prepared by co-evaporation method as well as the optimization of process condition. The total thickness of back electrode was fixed at 1 ${\mu}m$ and the structural, electric and optical properties of CIGS thin film were investigated by varying the thickness of Mo:Na bottom layer from 0 to 500 nm. From the experimental results, the content of Na was appeared as 0.28 atomic percent when the thickness of Mo:Na layer was 300 nm with compactly densified plate-shape surface morphology. From the XRD measurements, (112) plane was the strongest preferential orientation together with secondary (220) and (204) planes affecting to the crystallization. The lowest roughness and resistivity were 2.67 nm and 3.9 ${\Omega}{\cdot}cm$, respectively. In addition, very high carrier density and hole mobility were recorded. From the optimization of Mo:Na layer, we have achieved the conversion efficiency of 9.59 percent.

• Journal of Sensor Science and Technology
• /
• v.17 no.1
• /
• pp.69-74
• /
• 2008

VOCs (Volatile Organic Compound) sensors were fabricated using $SnO_2$nanowires-based thin films and its gas sensing behaviors were studied. The $SnO_2$ nanowires synthesized from a thermal evaporation process were dispersed in a solution and the sensor film was prepared by dropping the slurry on the substrate with the electrodes and an embedded heater. The gas response (Ra/Rg, Ra: resistance in air, Rg: resistance in gas) to $30{\sim}40$ ppm Benzene, Ethyl Benzene, o-xylene were in the range of $39{\sim}42$, which were significantly higher than those to 50 ppm of CO, $CH_4$ and $C_3H_8$ ($12{\sim}19$).