• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.361-361
• /
• 2011

Cu(InGa)(SeS2) (CIGS) thin film solar cells have recently reached an efficiency of 20%. Recent studies suggest a double graded band gap structure of the CIGS absorber layer to be a key issue in the production of high efficiency thin film solar cell using by sputtering process method. In this study, Cu(InGa)(SeS2) absorbers were manufactured by selenization and surfulization, we have deposited CIG precusor by sputtering and Se layer by evaporation before selenization. The objective of this study is to find out surfulization effects to improve Voc and to compare with non-surfulization Cu(InGa)Se2 absorbers. Even if we didn't analysis Ga depth profile of Cu(InGa)(SeS2) absorbers, we confirmed increasing of Eg and Voc through surlization process. In non-surfulization Cu(InGa)Se2 absorbers, Eg and Voc are 0.96eV and 0.48V. Whereas Eg and Voc of Cu(InGa)(SeS2) absorbers are 1.16eV and 0.57V. And the efficiency of 9.58% was achieved on 0.57cm2 sized SLG substrate. In this study, we will be discussed to improve Eg and Voc through surfulization and the other method without H2S. gas.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.11
• /
• pp.1379-1389
• /
• 1999

A new technique for control of size and shape of flame-made particles is Introduced. The characteristic sintering time can be controlled Independently of collision time by heating the particles with irradiation of laser because the sintering time strongly depends on temperature. A coflow oxy-hydrogen diffusion flame burner was used for $SiCl_4$ conversion to silica particle. Nanometer sized aggregates irradiated by a high power CW $CO_2$ laser beam were rapidly heated up to high temperatures and then were sintered to approach volume-equivalent spheres. The sphere collides much slower than the aggregate, which results in reduction of sizes of particles maintaining spherical shape. Light scattering of Ar ion laser and TEM observation using a local sampling device were used to confirm the above effects. When the $CO_2$ laser was irradiated at low position from the burner surface, particle generation due to gas absorption of laser beam occurred and thus scattering intensity increased with $CO_2$ laser power. At high irradiation position, scattering intensity decreased with $CO_2$ laser power and TEM image showed a clear mark of evaporation and recondensation of particles for high $CO_2$ laser power. When the laser was irradiated between the above two positions where small aggregates exist, average size of spherical particles obviously decreased to 58% of those without $CO_2$ laser irradiation with the spherical shape. Even for increased carrier gas flow rate by a factor of three, TEM photograph also revealed considerable reduction of particle size.

• The Journal of the Korea Contents Association
• /
• v.16 no.5
• /
• pp.660-667
• /
• 2016

Conventional decontamination methods utilize water-based systems, which generate high amounts of secondary wastes. Herein, we describe an environmentally benign decontamination method using liquid and supercritical $CO_2$. The use of $CO_2$ as a solvent affords effective waste reduction by its ability to be recycled, thereby leaving be hind only the contaminants upon its evaporation. In this study, a $CO_2$ solution process was assessed using t-salen(t-butylsalen), DC18C6 (dicyclohexano-18Crown6), 8-HQN(8-hydroxyquinoline), NEt4PFOSA(perfluoro-1-octanesulfonic acid tetra-ethyl ammonium salt), and NEt4PFOA(pentadecafluorooctanoic acid ammonium salt) to extract spiked radioactive contaminants(Nb,Zr,Co,Sr) from an inert sample matrix, namely filter paper. With the static extraction method, Sr was extracted with a maximum extraction rate of 97%, and Nb was extracted with a maximum extraction rate of 75%. Additionally, we were also able to extract Co and Zr with maximum extract ion ratesof 73% and 64%, respectively.

• Journal of Sensor Science and Technology
• /
• v.1 no.2
• /
• pp.117-123
• /
• 1992

$Pt-SnO_{2-x}$ thin film sensing devices has been fabricated by thermal oxidation of stacked Pt-Sn thin film on the heater. The thickness of Sn thin film deposited by thermal evaporation was $4000{\AA}$ and the thickness of Pt deposited by D. C. sputtering on Sn thin film was $14{\sim}71{\AA}$ range. The XRD analysis show that the $Pt-SnO_{2-x}$ thin films are formed by grains with a diameter of about $200{\AA}$ randomly connected and the crystalline phase of the thin films are preferentally oriented in the (110) direction. $Pt-SnO_{2-x}$ thin film device (Pt thickness : $43{\AA}$) to 6000 ppm CO shows the sensitivity of 80% and high selectivity to CO. And the operating temperature and the thermal oxidation temperature of $Pt-SnO_{2-x}$ thin film device with high sensitivity to CO were $200^{\circ}C$ and $500^{\circ}C$, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.1
• /
• pp.20-26
• /
• 2001

Titanium boride ($\textrn{TiB}_{x}$) films were deposited on (100) silicon substrates at the substrate temperature of $500^{\circ}C$ by means of the co-evaporation of titanium and boron evaporants during deposition. The co-evaporation method makes it possible to deposit the non-stoichiometric films with different boron-to-titanium ratio($0{\le}B/Ti \le 2.5$). The resistivity increases linearly as the boron-to-titanium ratio in the as-deposited films is increased. The surface roughness of $\textrn{TiB}_{x}$ films is changed as a function of the boron-to-titanium ratio. The XRD spectrum for pure titanium film shows a highly (002) preferred orientation. For B/Ti=0.59 ratio only a single TiB phase that shows a (111) preferred orientation is observed. However, the $\textrn{TiB}_{x}$ phase with the hexagonal structure of the $AlB_2$(C32) type appears as the boron concentration increase, and only a single $\textrn{TiB}_{x}$ phase is observed for $B/Ti \ge 2.0$ ratio. The $\textrn{TiB}_{x}$/Si samples reveal a tensile stress (3~$20{\times}^9$dyn/$\textrm{cm}^2$) in the overall composition of the films, although the magnitude of the residual stresses is depended on the nominal B/Ti ratio.

• KSBB Journal
• /
• v.22 no.5
• /
• pp.328-335
• /
• 2007

In this work ursolic acid (UA), a poorly water-soluble compound, was inclusion complexed with 2-hydroxypropyl-$\beta$-cyclodextrin (HP-$\beta$-CD) by various methods such as kneading, solvent evaporation and two types of supercritical fluid processes. The solubility and characteristics of these UA/HP-$\beta$-CD complexes were investigated by scanning electron microscopy, x-ray diffraction and HPLC. The water solubilities of the two complexes obtained from solvent evaporation and ASES processes were observed to increase up to 6$\sim$240 folds and 12$\sim$56 folds, respectively, compared with that of unprocessed UA. The stability of UA/HP-$\beta$-CD complex samples in cosmetic formulations was examined at various temperatures for one month. The UA/HP-$\beta$-CD complex prepared by solvent evaporation was found to be most stable among all the cosmetic formulations tested in our experiments.

• Membrane Journal
• /
• v.22 no.2
• /
• pp.128-134
• /
• 2012

In this study, hydroxy polyimide (HPI) was prepared for non-porous membrane by solvent evaporation method. As the result of gas permeance properties measurement, $CO_2$ permeability was 85 Barrer and the $CO_2/N_2$ selectivity was 23 at $30^{\circ}C$. Flat sheet membrane and hollow fiber membrane were prepared by using ternary system of polymer, solvent and non-solvent additive. Morphologies and gas permeance properties were measured by FE-SEM and bubble flow meter. Each $CO_2$ permeability of 18.28 GPU, 70 GPU and $CO_2/N_2$ selectivity of 6.72, 8.63 at $30^{\circ}C$ in the flat sheet membrane and hollow fiber membrane. Hollow fiber membrane has gas permeance property better than flat sheet membrane.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.3
• /
• pp.191-200
• /
• 2016

The ventilation effect of a ventilation system, which is classified as the forced ventilation and natural ventilation, is predominantly dependent on the combination of air supply and discharge. Perhaps the simplest ventilation is merely supplying the air as it is. However, to improve the indoor working environment during the summer, an air supply that is cooled to some extent has been widely adopted. Recently, a cooling method utilizing the vaporization of water was introduced. In this study, the performance of an evaporation-type air supply unit that was produced by Japan K-company and was installed in a shoe-manufacturing plant in Busan was investigated. The purpose of the experiment was to measure how much the supplied air could be cooled. From this experimental study, we confirmed that the evaporation-type air supply system is efficient, capable of improving the working environment during the summer while minimizing the energy cost.

• Journal of Environmental Science International
• /
• v.22 no.2
• /
• pp.243-249
• /
• 2013

Fibers of microbial polyesters, poly(3-hydroxy butyrate) (PHB) and poly(3-hydroxy butyrate-co-3-hydroxy valerate) (HB-co-HV) were prepared by electrospinning method. The obtained fibers were evaluated by differential scanning calorimetry, scanning electron microscopy, and oil absorption. The formation of fibers was strongly dependent on a concentration of solution. At a low concentration, the fibers contained beads which is from aggregation of polymer due to short evaporation time. The fine fibers with $2-5{\mu}m$ diameter were obtained at 20 wt% concentration. The contact angle measurement showed that the fiber had higher water contact angle than the film due to the lotus-like effect. Oil absorbency showed that the fiber had higher than the film. Specially, the HB-co-HV fiber which was spinned from 20 wt% absorbed 65% oil which is much higher than that of a normal polypropylene-based oil paper.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.3
• /
• pp.282-292
• /
• 2007

The present paper describes the results of high speed photography, acoustic emission (AE) detection and plasma light emission (LE) measurement during $CO_2$ laser welding of 304 stainless steel in different processing conditions. Video images with high spatial and temporal resolution allowed to observe the melt dynamics and keyhole evolution. The existence of keyhole was confirmed by the slag motion on the weld pool. The characteristic frequencies of flow instability and keyhole fluctuations at different welding speed were measured and compared with the results of Fourier analyses of temporal AE and LE spectra. The experimental results were compared with the newly developed numerical model of keyhole dynamics. The model is based on the assumption that the propagation of front part of keyhole into material is due to the melt ejection driven by laser induced surface evaporation. The calculations predict that a high speed melt flow is induced at the front part of keyhole when the sample travel speed exceeds several 10 mm/s. The numerical analysis also shows the hump formation on the front keyhole wall surface. Experimentally observed melt behavior and transformation of the AE and LE spectra with variation of welding speed are qualitatively in good agreement with the model predictions.