• KEPCO Journal on Electric Power and Energy
• /
• 제1권1호
• /
• pp.151-156
• /
• 2015

In order to improve the properties of high-temperature superconducting wire for superconducting cable system, we optimized the electro-polishing (EP), ion-beam assisted deposition (IBAD), superconducting (SC) layer, and baking (heat) treatment. The buffer layer was deposited on electro-polished substrate with RMS roughness ($R_{RMS}$) less than 5 nm. The IBAD process was carried out at $V_{beam}$: 1100 V and $V_{accel}$: 850 V that resulted in highly crystalline film of $LaMnO_3$. Chemical composition of SC layer is key to higher critical current, and we found that composition can be determined by surface color of SC layer. We adopt a proprietary contorl system based on RGB analysis of the surface and achieved critical current of 150 A/4 mm-width. The proposed baking treatment resulted in decreasing of about 10% of fraction defects.

• 설비공학논문집
• /
• 제16권12호
• /
• pp.1134-1139
• /
• 2004

The evaporative heat transfer coefficient of $CO_2$ (R-744) in a horizontal tube was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator (test section). The test section consists of a smooth, horizontal stainless steel tube of inner diameter of 7.75 mm. The experiments were conducted at mass flux of 200 to 500 kg/m$^2$s, saturation temperature of -5 to 5$^{\circ}C$, and heat flux of 10 to 40kW/m$^2$. The test results showed the heat transfer of $CO_2$ has a greater effect on nucleate boiling more than convective boiling. Mass flux of $CO_2$ does not affect nucleate boiling too much, and the effect of mass flux on evaporative heat transfer of $CO_2$ is much smaller than that of refrigerant R-22 and R-134a. In comparison with test results and existing correlations, correlations failed to predict the evaporative heat transfer coefficient of $CO_2$, therefore, it is necessary to develope reliable and accurate predictions determining the evaporative heat transfer coefficient of $CO_2$ in a horizontal tube.

• 청정기술
• /
• 제12권2호
• /
• pp.101-106
• /
• 2006

본 연구에서는 수산화물 전구체로부터 HT-$LiCoO_2$ 분말을 제조하였다. 사용된 $Co(OH)_2$는 ${\alpha}$상 및, 또는 ${\beta}$ 상의 수산화물이며 여러 조건에서 침전법으로 제조되었다. 제조시에 $[OH^-]/[CO^{2+}]$ 농도 비와 숙성시간을 조절함으로써 원하는 특성을 지닌 $Co(OH)_2$ 제조가 가능하였다. 침전법으로 합성한 $Co(OH)_2$와 LiOH를 메탄올 수용액을 이용하여 혼합한 후 이어서 증발, 건조 그리고 숙성 조작에 의하여 HT-$LiCoO_2$의 전구체를 합성하였다. 숙성기간에 tailor-made ${\beta}$-phase $Co(OH)_2$는 CoOOH로 변환되면서 고용체를 형성한다. 이 같은 결과로 HT-$LiCoO_2$가 낮은 온도($600^{\circ}C$), 짧은 시간(10분)에 합성이 가능하게 된다.

• 한국자기학회지
• /
• 제5권1호
• /
• pp.48-53
• /
• 1995

동시 열진공증착한 Ag-Co 미세입상 합금박막의 구조, 자기적 성질 및 거대자기저항 현상에 관하여 연구하였다. 증착된 상태에서 합금박막은 과포화된 Ag 기지와 석출된 Co 입자들이 공존하는 준안정한 fcc 구조를 이루고 있다. Co의 양이 20에서 55 at.%로 증가함에 따라 Ag 기지의 입자크기는 평균 147에서 $67{\AA}$으로 감소하였고 Ag 기지에 Co의 고용량은 2.5에서 6.7%로 증가하였다. 25 at.% 이하의 조성을 갖는 합금박막은 주로 초상자성 특성을 보였으며 그 이상의 조성에서는 초상자성과 강자성이 혼합된 거동을 보였다. 증착된 상태의 30 at.% 합금 박막에서(상온, 10 kOe) 최대 19%의 자기저항비를 얻었다. 증착된 상태에서 대부분의 코발트가 석출되어 있기 때문에 Cu-Co계와는 달리 열처리에 의해 MR비의 증가는 보이 지 않았다.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2006년도 에너지.가스.기후변화학회 연합춘계학술대회 및 특별심포지움
• /
• pp.311-316
• /
• 2006

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1995년도 제9회 학술발표회 논문개요집
• /
• pp.138-138
• /
• 1995

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2005년도 춘계학술발표대회 및 제8회 신소재 심포지엄 논문개요집
• /
• pp.202-202
• /
• 2005

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1998년도 IUMRS-ICEM ABSTRACT BOOK
• /
• pp.152.1-152
• /
• 1998

• 한국진공학회지
• /
• 제8권4A호
• /
• pp.482-489
• /
• 1999

AC PDP(P1asma Display Pane1)s use the mixture of inert gases to generate a discharge inside the display pixels. Impurities such as CO, $CO_2$ and OH inside discharge region may deteriorate the characteristics of PDP operation during long life time of PDP. Electro-negative gas such as CO can cause the sustain pulse amplitude to rise by attaching electrons which will play an important role in the earlier stage of the discharge. MgO film is used to protect the dielectric layer in AC PDP, and is in contact with the free space of display pixel where it is filled with the inert gas mixture. So, MgO film can be a main source of impurities. In this experiment, we observed the change of impurity generation of various MgO films which were deposited by different methods, by using QMS. (quadropole mass spectrometer) The main impurites were $H_2$, CO and $CO_2$. And with the comparison of the TPD (temperature programmed desorption) result, it can be understood that impurity gases are generated by sputtering of MgO surface not by outgassing. Deposition method had effects on the characteristics of the impurity generation. The MgO film manufactured by e-beam evaporation generated more amount of impurity gases than the MgO films manufactured by sputtering or ion-plating. And also heat treatment of MgO film after deposition decreased the magnitude of impurity gas generation.

• 한국기계가공학회지
• /
• 제19권3호
• /
• pp.51-56
• /
• 2020

Research into natural refrigerants that use CO₂, instead of chlorofluorocarbons and hydrofluorocarbons, has increased due to the environmental problems caused by ozone depletion. CO₂ refrigerants are more environmentally friendly than conventional refrigerants because they have better latent heat of evaporation and heat transfer efficiency properties. However, they have very low critical temperatures and require high design pressures; therefore, pressure control valves, which reduce the pressure of the CO₂ refrigerant to a safe level and apply it to the refrigerant air conditioning system, are necessary to secure stability against high pressure. In the present study, we evaluated the flow characteristics and valve performance of the pressure control valve using a CO₂ refrigerant by measuring the pressure, velocity, and flow coefficient. In addition, we examined the applied forces caused by the internal pressure from the highly pressurized CO₂ refrigerant and required thrust characteristics.