• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2001년도 춘계연구발표회 논문개요집
• /
• pp.114-115
• /
• 2001

• 한국자기학회지
• /
• 제11권5호
• /
• pp.184-188
• /
• 2001

DC-스퍼터를 이용하여 기판온도를 실온과 20$0^{\circ}C$로 변화시켜 , 균일한 내부구조를 갖는 구조와 결정립내부에 미세한 자가정렬나노구조(SONS)를 갖는 Co-22%Cr 합금 박막을 각각 제조하고 이들의 미세구조와 도메인구조를 투과전자현미경(TEM)과 자기력현미경(MFM)을 이용하여 확인하였다. Co가 먼저 부식되도록 조치하고 관찰한 투과전자현미경 결과, 실온에서 제작된 박막의 경우에는 결정립 내부가 균일한 조성을 보인 반면, 기판온도가 20$0^{\circ}C$인 Co-22%Cr합금 박막은 결정립 내부에 SONS를 형성하여 판상의 미세 Co-과잉상을 가지는 특이한 미세구조를 가지는 것을 확인하였다. 자기력현미경에 의해 확인된 결과, SONS가 없는 시편(기판온도를 실온으로 유지한 경우)은 주기 5000 정도의 미로형 도메인(domains)이 생겼다. 미로형 도메인은 결정간의 교환에너지가 큰 경우 발생하는 구조로서 고밀도 자기기록이 불리할 것이 예상되었다. 이와 비교해서 SONS가 생성된 (기판온도를 20$0^{\circ}C$로 유지한 경우)시편은 주기 500 정도의 매우 미세한 구형 도메인을 보였다. 미세구형 도메인은 각 도메인간의 교환에너지가 작아 열적 변화에도 데이터가 안정하므로 고밀도 기록에 유리하다고 예상되었다.

• 한국콘텐츠학회논문지
• /
• 제10권11호
• /
• pp.228-234
• /
• 2010

치과도재용 합금으로 사용되는 합금 중 베릴륨이 함유된 비귀금속 Ni-Cr합금과 베릴륨이 함유되지 않은 비귀금속 Ni-Cr합금 그리고 베릴륨이 함유되지 않은 비귀금속 Co-Cr 합금과 세라믹간의 결합강도와 파절양상 그리고 계면특성을 분석하고자 하였다. 결합강도는 만능시험기를 이용하여 전단력시험을 통하여 전단결합력을 측정하였으며, 전단시험에 의한 파단면을 이용하여 파절양상을 관찰하였다. 그리고 합금-도재간의 계면을 관찰하였다. 전단결합강도 측정 결과, 베릴륨이 포함된 T-3가 41.13(${\pm}5.11$)MPa로 가장 높게 나타났으며, 베릴륨이 포함된 VeraBond(40.72(${\pm}5.98$)MPa), Co-Cr 합금인 Wirobond(38.40(${\pm}9.66$)MPa), 베릴륨이 포함되지 않은 Verabond 2V(32.77(${\pm}4.31$)MPa), Bellabond N(28.63(${\pm}6.39$)MPa), Bellabond plus(24.97(${\pm}6.13$)MPa), Argeloy N.P. Star(22.69(${\pm}3.41$)MPa) 순으로 나타났다. 비귀금속 합금들과 세라믹간의 파절양상은 모든 시편에서 금속표면에 세라믹이 일부 부착된 복합파절(mixed failure) 양상을 보였다.

• 대한치과보철학회지
• /
• 제27권1호
• /
• pp.49-54
• /
• 1989

The purpose of this study was to investigate the interfacial elemental change when solding the Ni-Co-Cr dental removable partial denture alloy and Fe-Cr-Ni wrought wire alloy with Ag-Cu-Zu Silver solder, by EDXA, EPMA, to investigate the appropriateness of clinical usefullness for repair the fractured clasps of removable partial dentive. The result of this study was as follows: 1. The Ni element of major component of Ticonium penetrate into the silver solder 2. The movement Age element of silver solder into Fe-Cr-Ni wire was not significant, by EDXA and EPMA.

• 한국레이저가공학회지
• /
• 제2권1호
• /
• pp.16-21
• /
• 1999

The surface of Alloy 600 was alloyed using a continuous wave $CO_2$ laser beam in order to improve its corrosion resistance. Laser surface alloying (LSA) was done by melting the surface electroplated with Cr of the alloy. The Cr concentration of the alloyed surface was 28-30 at.%, which is similar to that of Alloy 690. Alloying elements in the alloyed layer was observed to be distributed very homogeneously all over the alloyed region. According to the electrochemical and modified Huey tests, the corrosion resistance, in particular the grain boundary corrosion resistance, of the LSA specimens was significantly improved, compared with that of the as-received(AR) specimen. This improved corrosion resistance of the alloyed specimen might be attributed to the high Cr content which could make possible formation of more stable and dense passive film onto its surface.

• 구강회복응용과학지
• /
• 제31권1호
• /
• pp.50-59
• /
• 2015

임플란트를 이용하여 심미 영역인 상악 전치부를 심미적, 기능적으로 수복하고 유지 관리하는 것은 어려운 일이다. 임플란트 주위염으로 인하여 치조골의 흡수, 치간유두의 수축 등과 같은 임플란트 주위 조직 문제와 금속 지대주의 노출로 인한 심미적 문제가 발생할 수 있기 때문이다. 본 증례에서는 기성지대주의 단점을 보완 가능한 맞춤형 지대주를 전통적인 제작 방식인 주조 방식으로 Co-Cr 합금을 이용하여 제작하고, 시멘트 유지형 보철물을 제작한 증례에 대해 보고하고자 한다.

• 열처리공학회지
• /
• 제37권2호
• /
• pp.58-65
• /
• 2024

In the present study, the effect of annealing condition on the microstructures and mechanical properties of the cold-rolled CoCrFeMnNi high entropy alloys were studied. Annealing treatment was performed under six different temperatures. Microstructural analyses confirmed that annealing below 800℃ resulted in the formation of intermetallic sigma (σ) phase within face-centered cubic (FCC) matrix, and this σ phase has beneficial effects on the formation of fine-grained structures through retardation of grain growth and recrystallization due to Zener pinning effect. This led to the enhanced yield strength and tensile strength of ~646 and ~855 MPa, respectively. The microstructures annealed above 800℃ demonstrated single FCC phase, and fully-recrystallized single FCC microstructure resulted in a slight increase in ductility with a considerable decrease in strength. The evolution of mechanical properties, such as strength, ductility, and strain hardening exponent, will be discussed.

• 한국재료학회지
• /
• 제15권12호
• /
• pp.773-779
• /
• 2005

Properties of Ni-base superalloys of Nimonic 80A alloy system were investigated by the observation of microstructures, precipitates ana hardness as a function of the chemical compositions ana the paths of heat treatment. The higher hardness values showed, the higher Ti/Al ratio among high compositions of Cr and Co element. The lower (Ti+Al) and Fe contents decreased in the same Ti/Al ratio, the higher hardness values showed. This results are considered that coherent deformation was increased with increasing Ti/Al ratio. Hardness showed higher value when Cr contents was $18 wt\%$ less than $21wt\%Cr$. In $3.15 wt\%$Co alloy, $\gamma'$ phase was very fine as around 50nm and, its volume fraction and hardness showed the highest value by 2step-aging treatment.

• Journal of Welding and Joining
• /
• 제26권1호
• /
• pp.50-55
• /
• 2008

A low alloy-steel(2.25Cr-1.0Mo) has been widely used for boiler piping, header and tubes in high temperature and pressure conditions of the thermal power plant. It is common knowledge that the repair welding is permitted two or three times by customary practice rule, but there is no regulation to limit the number of repair welding base on the study heat-affected zone(HAZ), which is the weakest zone when repair welding is under taken, by experiments about the metallographic degradation and mechanical properties. Therefore, this study aims to verify the reliability of 5 times repair welding through conducting the experimental observation in the mechanical and the metallographic change on HAZ varying repair welding times. In results of the experiments, it is concluded that the reliability was kept in HAZ even up to the fifth repairs.

• 대한치과기공학회지
• /
• 제33권4호
• /
• pp.349-357
• /
• 2011

Purpose: In this study, for the reasons of observing the changes when using bonding agent with Ni-Cr alloy and Co-Cr alloy and using VM13 and Vintage MP ceramic which have the disparity in coefficient of thermal expansion, it is carried out to evaluate the characteristics of the bonding agent through the analysis of the interface between metal and ceramic and the analysis of bond strength by variable. Methods: The surface treatment was performed on the two kinds of alloy(Ni-Cr alloy and Co-Cr alloy) specimens, which were sandblasted and were treated with bonder application. The metal-ceramic interfaces were analyzed with EPMA in order to ionic diffusion, and the shear test was performed. Results: As a result of observation of metal-ceramic interfacial properties, it was observed that Cr atoms were spread from the alloy body to the ceramic floor in the specimen of Group B. It was also seen that Cr, W atoms were spread from the alloy body to the ceramic floor in the specimen of Group S. In consequence of observing Shear bond strength, it was calculated that the specimen of BSV was 27.75(${\pm}11.21$)MPa, BSM was 27.02(${\pm}5.23$)MPa, BCV was 30.20(${\pm}5.99$)MPa, BCM was 27.94(${\pm}10.76$)MPa, SSV was 20.83(${\pm}2.58$)MPa, SSM was 23.98(${\pm}3.94$)MPa, SCV was 32.32(${\pm}4.68$)MPa, and SCM was 34.54(${\pm}10.63$)MPa. Conclusion: In the metal-ceramic interface of Bellabond plus sample group, diffusion of Cr atoms was incurred and diffusion of C Cr atoms and W atoms in the sample group of $Starloy{(R)}\;C$ was observed. Using bonding agent showed the higher bond strength than using the sand blasting treatment. In the Bellabond plus alloys, the specimen group with the use of binding materials showed higher shear bond strength, but didn't show statistically significant differences (p>0.05). In the $Starloy{(R)}\;C$ alloys, the specimen group with the use of binding materials showed higher shear bond strength and statistically significant differences(p<0.05). In terms of VM13 ceramic, it was in the Bellabond plus alloys that the high shear bond strength was showed, but there's no statistically significant differences(p>0.05). In terms of Vintage MP ceramic, it was in the $Starloy{(R)}\;C$ alloys that the high shear bond strength was showed and statistically significant differences(p<0.05). Metal-ceramic to fracture of the shear strength measurements and an analysis of all aspects of military usage fracture of the composite, respectively.