• 한국자동차공학회논문집
• /
• 제3권2호
• /
• pp.30-41
• /
• 1995

Gear rattle is a source of vibration and noise in automotive gearbox casing and generally occurs at or near system resonant frequencies. The neutral gear rattle of the gearbox. is affected by the stiffness and hysteresis torque in the clutch disk and drag torque determining balancing point of the clutch disk operating range. The experiment is carried out in the pre-damper type clutch and a manual transmission of a automobile equipped for inline four-sylinder four-cycle 1.5L MPI engine and the computer simulation is executed by 5th order Runge-Kutta method. The results of the simulation analysis and experimental studies show the dynamic behavior of clutch and a phenomenon of the neutral gear rattle with respect to drag torque and torsional characteristics of the clutch.

• Journal of Mechanical Science and Technology
• /
• 제14권5호
• /
• pp.508-517
• /
• 2000

For shift quality improvement, torque sensors are currently too expensive to be used on production vehicles. To achieve smooth acceleration shift, the reference trajectory of the clutch slip speed for accomplishing the shift process within a designated shift completion time and its relationship with the clutch actuating torque were suggested by Jeong and Lee (1999). In order to facilitate the proposed algorithm, nonlinear estimators for necessary information such as the axle shaft torque, clutch friction and turbine torque were designed using only speed sensors. Accounting for the modeling error, a control law for this indirect smooth shift was proposed based on the above mentioned suggestions. Simulation results of the proposed estimators and shift controller were presented and further considerations for practical applications are discussed.

• Journal of Oral Medicine and Pain
• /
• 제24권2호
• /
• pp.207-217
• /
• 1999

This study was performed to investigate the effects of clutch adaptation on the mandibular rotational torque movement in normal people. 69 dental students were selected for the study. Their mean age were 23.6 years and they did not present any signs and symptoms of temporomandibular disorders. $BioEGN^{(R)}$ with $Rotate^{(R)}$ program was used to observe and record the amount of mandibular rotational torque on protrusion, on right excursion, on left excursion, and on comfortable wide opening movement. The natural tooth contact movement and the movement with clutch were performed in the above four each mandibular movement. Clutch was made by the method used in $Pantronic^{(R)}$ clutch fabrication. Distance of slant frontal which was translatory trajectory in frontal plane and degree of rotational torque in horizontal and in frontal plane were recorded. The data obtained were processed with SPSSWIN program and the results were as follows : 1. Distance of slant frontal in each mandibular movement generally increased with clutch. 2. Degree of rotational torque in horizontal and in frontal plane on protrusion and on lateral excursions did not increase with clutch, but the degree on wide opening increased with clutch. 3. Degree of rotational torque in horizontal plane on protrusion and on lateral excursions did not show any difference between right and left side, but the degree in frontal plane on protrusion and on lateral excursions showed significant difference between right and left side. 4. Total amount of rotational torque from right and left sides on protrusion and lateral excursions were not increased with clutch, but the degree on wide opening movement was increased with clutch. And in this case, degree in horizontal plane was larger than that in frontal plane. 5. Correlation between total amount of rotational torque in horizontal plane and that in frontal plane were highly significant on protrusion and on lateral excursions with or without clutch, but the significant correlation on wide opening without clutch became not significant with clutch.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.718-727
• /
• 2000

Nowadays, most passenger cars equipped with automatic transmissions use torque converter clutches to reduce fuel consumption, and recently the slip control scheme of torque converter clutches is widely studied for the expansion of the operating region of torque converter clutches and thus for the further improvement of the fuel economy of vehicles. In this study, the analysis of the torque converter clutch system including the line pressure control unit of the automatic transmission and the actuating hydraulic control unit of the torque converter clutch is performed, and a feedforward controller and a fuzzy logic controller for its slip control are proposed. Also, for the slip controller to use the grade resistance information during control, an observer-based grade resistance estimator is designed. The performance of the designed grade resistance estimator and the slip controller is verified by dynamic simulations, and the effect of the torque converter clutch slip control on the fuel economy is examined using a driving cycle simulation.

• 한국소음진동공학회논문집
• /
• 제19권8호
• /
• pp.795-801
• /
• 2009

This paper presents an optimal design of a magnetorheological(MR) fan clutch based on finite element analysis and also presents torque control of engine cooling fan using a sliding mode control. The MR fan clutch is constrained in a specific volume and the optimization problem identifies the geometric dimension of the fan clutch that minimizes an objective function. The objective function for the optimization problem is determined based on the solution of the magnetic circuit of the initially designed clutch. Under consideration of spatial limitation, design parameters are optimally determined using finite element analysis. After describing the configuration of the MR fan clutch, the viscous torque and controllable torque are obtained on the basis of the Bingham model of MR fluid. Then, a sliding mode controller is designed to control the torque of the fan clutch according to engine room temperature and control performance is evaluated through computer simulation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.633-638
• /
• 2009

This paper presents an optimal design of a magnetorheological(MR) fan clutch based on finite element analysis and also presents torque control of engine cooling fan using a sliding mode control. The MR fan clutch is constrained in a specific volume and the optimization problem identifies the geometric dimension of the fan clutch that minimizes an objective function. The objective function for the optimization problem is determined based on the solution of the magnetic circuit of the initially designed clutch. Under consideration of spatial limitation, design parameters are optimally determined using finite element analysis. After describing the configuration of the MR fan clutch, the viscous torque and controllable torque are obtained on the basis of the Bingham model of MR fluid. Then, a sliding mode controller is designed to control the torque of the fan clutch according to engine room temperature and control performance is evaluated through computer simulation.

• Tribology and Lubricants
• /
• 제33권2호
• /
• pp.71-78
• /
• 2017

The drag torque in the wet clutch system of a dual clutch transmission system is investigated because it is relatively high, up to 10 of the total output torque of the engine, even when the clutch is in the disengagement state with zero torque transfer. Drag torque results from the shear resistance of the DCTF between the friction pad and separator plate. To reduce the drag torque for ensuring fuel economy, the groove pattern of the wet clutch friction pad is designed to have a high flow rate through the pattern groove. In this study, four types of groove patterns on the friction pad are designed. The volume fraction of the DCTF (VOF) and hydrodynamic pressure developments in the gap between the friction pad and separator plate are computed to correlate with the computation of the drag torque. From the computational results, it is found that a high VOF and hydrodynamics increase the drag torque resulting from the shear resistance of the DCTF. Therefore, a patterned groove design should be used for increasing the flow rate to have more air parts in the gap to reduce the drag torque. In this study, ANSYS FLUENT is used to solve the flow analysis.

• Tribology and Lubricants
• /
• 제30권6호
• /
• pp.337-342
• /
• 2014

The reduction of drag torque is an important research issue in terms of improving transmission efficiency. Drag torque in a wet clutch occurs because of the viscous drag generated by the transmission fluid in a narrow gap (clearance) between the friction plate and a separate plate. The objective of this paper is to observe the effects of the friction plate area and the clearance on the drag torque using finite element simulation. The two-phase flow of air and oil fluid is considered and modeled for the simulation. The simulation analysis reveals that as the rotational speed increases, the drag torque generally increases to a critical point and then decreases sharply at a high speed regime. The clearance between the two plates plays an important role in controlling drag torque peak. An increase in the clearance causes a decrease in shear stress; thus, the drag torque also decreases according to Newton's law of viscosity. An observation of the effect of the area of contact between transmission fluid and friction plate shows that the drag torque increases with the contact area. The flow vectors inside the flow channel present clear evidence that the velocity of the fluid flows is faster with a larger friction plate, that is, in the case of a larger contact area. Therefore, the optimum size of the friction plate should be determined carefully, considering both the clutch performance and drag reduction. It is expected that the results from this study can be very useful as a database for clutch design and to predict the drag torque for the initial design with respect to various clutch parameters.

• Journal of Mechanical Science and Technology
• /
• 제14권5호
• /
• pp.499-507
• /
• 2000

Smooth shift is one of the key issues in automatic power transmission control systems. However, the torque sensors are too expensive to be used in shift controllers on production vehicles. In order to provide a basic strategy for smooth shifting by using RPM sensors only and in order to accomplish the shift within a designated time, this paper studies detailed characteristics of the smooth shift for clutch-to-clutch shift mechanism. A desired trajectory of slip speed is proposed for smooth acceleration shift defined in this paper. Also the clutch torque needed to achieve this trajectory is derived, and it may be used as a open loop shift control law.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.562-566
• /
• 1997

The main torsional vibration source of the driveline is the fluctuation of the engine torque. The gear rattle is impacts generating in the backlash of the free gear due to this torsional vibration Optimization of the clutch torsional characteristic is one of the effective methods to reduce the idle gear rattle. Many researches have been reported on this problem but only few of them give sufficient consideration to the full clutch design parameters(stiffness, hysteresis torque, preload, first stage length) and drag torque This paper pays attention to the gear impact mechanism, clutch design parameters and drag torque to reduce the idle gear rattle with computer simulation.