• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.3
• /
• pp.47-56
• /
• 2005

This paper presents a performance improvement result with the aid of closed feedback controller loop to a micro gyroscope. The dynamic model of a micro gyroscope is derived and a conventional proportional and derivative controller is designed via frequency domain analysis. The proposed control loop is implemented using several analog devices and applied to the SNU-Bosch MEMS gyroscope to check its performance improvement in real environment. The experiments demonstrated the performance improvement with the proposed feedback control loop. The bandwidth, linearity, and bias stability are improved to 78 Hz, 0.504 %, and 0.043 deg/sec, respectively, from 35 Hz, 2.07 %, and 0.066 deg/sec of open loop system.

• Journal of Climate Change Research
• /
• v.7 no.4
• /
• pp.397-405
• /
• 2016

For better understand of the soil respiration characteristic in ecosystem, it is necessary to accurately determine the daily, monthly and seasonal $CO_2$ flux related to various environmental factors. In general, soil respiration is being measured on a sunny day. But soil respiration is known to be affected by soil temperature and soil moisture content. In case of forestry, changes in soil moisture content are entirely dependent on rainfall. If we calculated the monthly soil respiration measured based on sunny days data only, it could be a factor that loses credibility soil respiration. On this study, we measured soil respiration on Pinus koraiensis plantation at Mt. Taehwa of Gwangju, Gyeonggi-do on sunny and rainy days in 2012, using Automatic Open-Closed Chamber system (AOCC) and portable $CO_2$ analyzer (GMP343). Then we computed the regression equations using sunny days data, precipitation less than 10 mm data, and precipitation over 10 mm data. At first, there were no significant differences in observed data and computed data. But less than 10 mm precipitation, computed data was 26.5% lower than observed data. Precipitation over 10 mm, on the other hand, the former was 29.3% higher than the latter. In each case, it showed significant differences between observed and computed data (p<0.05). So if we computed regression equation using soil respiration measured sunny days only, about 30% of annual soil respiration could be overestimated. Through further study, we suggest the subdivision and computation of regression equation on the basis of the rainfall intensity.

• The korean journal of orthodontics
• /
• v.42 no.4
• /
• pp.218-224
• /
• 2012

Objective: To investigate the resistance to sliding (RS) in self-ligating and conventional ligation bracket systems at 5 different second-order bracket angulations by using low-stiffness alignment wires in a 3-bracket experimental model and to verify the performance of the main RS components in both systems when these wires are used. Methods: Interactive self-ligating brackets with closed and open slides were used for the self-ligating (SL) and conventional ligation (CL) groups, respectively; elastomeric ligatures (1 mm inner diameter) were used in the latter system. The alignment wire used was 0.014 inch heat-activated NiTi (austenitic finish temperature set at $36^{\circ}C$ by the manufacturer). A custom-made testing machine was used to measure frictional resistance. Tests were repeated 5 times at every angulation simulated. All data were analyzed statistically. Results: The RS increased significantly with increasing angulation in both SL and CL groups (p < 0.0001). However, the RS values were significantly higher at every angulation (p < 0.0001) in the CL group. Conclusions: Despite the relevance of the binding phenomenon, ligation forces predominantly affect the RS when lowstiffness alignment wires are used.

• Journal of Gastric Cancer
• /
• v.16 no.3
• /
• pp.152-160
• /
• 2016

Purpose: Endoscopic diagnosis of gastric cancer (GC) that emerges after eradication of Helicobacter pylori may be affected by unique morphological changes. Using comprehensive endoscopic imaging, which can reveal biological alterations in gastric mucosa after eradication, previous studies demonstrated that Congo red chromoendoscopy (CRE) might clearly show an acid non-secretory area (ANA) with malignant potential, while autofluorescence imaging (AFI) without drug injection or dyeing may achieve early detection or prediction of GC. We aimed to determine whether AFI might be an alternative to CRE for identification of high-risk areas of gastric carcinogenesis after eradication. Materials and Methods: We included 27 sequential patients with metachronous GC detected during endoscopic surveillance for a mean of 82.8 months after curative endoscopic resection for primary GC and eradication. After their H. pylori infection status was evaluated by clinical interviews and $^{13}C$-urea breath tests, the consistency in the extension of corpus atrophy (e.g., open-type or closed-type atrophy) between AFI and CRE was investigated as a primary endpoint. Results: Inconsistencies in atrophic extension between AFI and CRE were observed in 6 of 27 patients, although CRE revealed all GC cases in the ANA. Interobserver and intraobserver agreements in the evaluation of atrophic extension by AFI were significantly less than those for CRE. Conclusions: We demonstrated that AFI findings might be less reliable for the evaluation of gastric mucosa with malignant potential after eradication than CRE findings. Therefore, special attention should be paid when we clinically evaluate AFI findings of background gastric mucosa after eradication (University Hospital Medical Information Network Center registration number: UMIN000020849).

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.207-213
• /
• 2012

With development of IT technology, B2C Social Commerce makes the change from closed type of transaction to the form of an open trading. Also by dramatically reducing the intermediate distribution and removing distribution costs, it provides goods at unbeatable prices to consumers. Depending on the flow of the times, the business-to-business struggles with the difficulty of PRM management and fast promotion of new products. Therefore, it is required B2B Social Commerce, new platform that can collect distribution and consumption firms in one place which is similar to B2C Social Commerce. Unlike the case of B2C social commerce, B2B Social Commerce should have an essential element, Installment payment system to pay over the period without purchase in accordance with the payment paid as a lump sum. B2B Social Commerce model which is introduced in this study will provide the solution of B2B transaction problems, opening up new markets and bring the expansion of the electronic market.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.961-967
• /
• 2007

Automatic water feeding system for chickens is the one of the most important devices at poultry farms. Chickens drink water directly from a water feeder nipple of the automatic water feeder. Check valve inside the water feeder nipple is open when they drink water and is closed otherwise. There are two types of nipples. One is the piston nipple, and the other is the ball nipple. Because the nipple stick in the ball nipple can move freely, the sloping mechanism of the ball nipple works well. but it has complicated mechanism. On the other hand, the piston nipple has very simple structure, but its movement is limited so it can move only up-and-down. To overcome those limitation, the piston nipple with sphere valve seat face (sphere face piston nipple) has been developed and is just distributed at domestic markets. The experimental performance test of the commercialized sphere piston nipple has been conducted, and compared with the performance of the ball nipple and the piston nipple which are domestic products. As the result, sphere piston nipple shows excellent performance compared to that of the piston nipple but its performance is similar to ball type nipple.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.1
• /
• pp.201-206
• /
• 2022

In this paper, a flushing system with automatic opening and closing function of the toilet cover was studied. It works by an infrared sensor attached to the cover is detected or not. When the infrared sensor of the open function detects it, the servomotor is driven on the toilet cover to raise the cover, and when the infrared sensor with the close function detects the infrared sensor, the cover is set to be lowered. A tilt sensor is attached to the inside of the cover to operate when the cover goes down, and when this is activated, the servomotor connected to the toilet lever opens the stopper of the supply port and sends water down. In addition, we minimized the inconveniences for the next user when they use the toilet by using the non-contact water level sensor and LED function to notice the water is clogged during the flushing process. Also, we implemented UV-LED function to prevent bacterial growth while the toilet is closed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.2
• /
• pp.121-131
• /
• 1986

The stiffness matrix of circularly curved frame elements including the warping effects is formulated by the solutions of vlasov's differential equations, and the procedure for the elastic static analysis of curved girder systems by the displacement method is presented. The validity of this method has been demonstrated by comparing the analysis results with other solutions. And if the tangential lines of the two frame element axes connected at any nodal point coincide, the transformation to the global coordinate system can be omitted when we analyze the structures consisting of circularly curved elements. The theory introduced in this thesis can be applied with sufficient accuracy to the structures built up with horizontally circular curved frame elements which have closed or open cross sections and are symmetric to the axis perpendicular to the plane of the curvature, such as prestressed concrete box girder bridges.

• Food Science and Preservation
• /
• v.16 no.6
• /
• pp.810-816
• /
• 2009

To identify effective food packaging compounds that could significantly affect the freshness of stored food, the efficiency and performance of porous polypropylene film containing mustard oil as a freshness maintenance ingredient was studied by GC-MS analysis and storage testing of bread. AITC (allyl-isothiocyanate)-emitting properties of films impregnated with mustard oil were evaluated by GC-MS. AITC was extracted from mustard oil, and used as a vapor as an effective antimicrobial agent. Films were prepared under four different conditions (the film types were abbreviated 25SF1, 25SF2, 50LF, and IAF) and the amounts of AITC inside vinyl packs constructed using the four films were measured. The results showed that the 25SF2 film (width 25 mm, length 20 cm) yielded a greater amount of AITC than did the 50LF film (width 50 mm, length 20 cm). We confirmed that the amount of gas emission showed better between layer and layer of the film side than the internal film. In storage testing using various films at $35^{\circ}C$ for 25 days, 25SF2 film provided excellent preservation of bread compared with 50LF film. This was in line with the fact that 25SF2 film yielded the highest amount of AITC. Emission capacities AITC of 2 cm film were measured using bottles various volumes (43 mL, 500 mL, 1000 mL) and both closed and open systems. The AITC content of the film in 43 mL bottle was much higher than that yielded by other films in the closed system, and AITC was rapidly emitted, with relatively low residual gas emission after 4 days in an open system. Mustard oil is a useful freshness maintenance ingredient hence, analysis of AITC emission kinetics from various films were helpful to develop films with optimal antimicrobial effects, and will allow application of such films in food packaging systems.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.342-343
• /
• 2013

AlSb is a promising material for optical devices, particularly for high-frequency and nonlinear-optical applications. And AlSb offers significant potential for devices such as quantum-well lasers, laser diodes, and heterojunction bipolar transistors. In this work we study molecular beam epitaxy (MBE) growth of an unstrained AISb film on a GaAs substrate and identify the real-time monitoring capabilities of in situ spectroscopic ellipsometry (SE). The samples were fabricated on semi-insulating (0 0 1) GaAs substrates using MBE system. A rotating sample stage ensured uniform film growth. The substrate was first heated to $620^{\circ}C$ under As2 to remove surface oxides. A GaAs buffer layer approximately 200 nm- thick was then grown at $580^{\circ}C$. During the temperature changing process from $580^{\circ}C$ to $530^{\circ}C$, As2 flux is maintained with the shutter for Ga being closed and the reflection high-energy electron diffraction (RHEED) pattern remaining at ($2{\times}4$). Upon reaching the preset temperature of $530^{\circ}C$, As shutter was promptly closed with Sb shutter open, resulting in the change of RHEED pattern from ($2{\times}4$) to ($1{\times}3$). This was followed by the growth of AlSb while using a rotating-compensator SE with a charge-coupled-device (CCD) detector to obtain real-time SE spectra from 0.74 to 6.48 eV. Fig. 1 shows the real time measured SE spectra of AlSb on GaAs in growth process. In the Fig. 1 (a), a change of ellipsometric parameter ${\Delta}$ is observed. The ${\Delta}$ is the parameter which contains thickness information of the sample, and it changes in a periodic from 0 to 180o with growth. The significant change of ${\Delta}$ at~0.4 min means that the growth of AlSb on GaAs has been started. Fig. 1b shows the changes of dielectric function with time over the range 0.74~6.48 eV. These changes mean phase transition from pseudodielectric function of GaAs to AlSb at~0.44 min. Fig. 2 shows the observed RHEED patterns in the growth process. The observed RHEED pattern of GaAs is ($2{\times}4$), and the pattern changes into ($1{\times}3$) with starting the growth of AlSb. This means that the RHEED pattern is in agreement with the result of SE measurements. These data show the importance and sensitivity of SE for real-time monitoring for materials growth by MBE. We performed the real-time monitoring of AlSb growth by using SE measurements, and it is good agreement with the results of RHEED pattern. This fact proves the importance and the sensitivity of SE technique for the real-time monitoring of film growth by using ellipsometry. We believe that these results will be useful in a number of contexts including more accurate optical properties for high speed device engineering.