• 한국세라믹학회지
• /
• 제35권9호
• /
• pp.988-994
• /
• 1998

In the manufacturing of vitreous bonded CBN tool the porosity change associated with various processing conditions, I. e. the sintering temperature and the size and the amount of abrasive grits was observed. In the case of sintering of vitreous bond material only the specimen density reached the maximum at 950$^{\circ}C$ and then the total porosity was increased slightly with the temperature above 950$^{\circ}C$. In the sintering of a-brasive grits and the vitreous bond material together a marked increase in the total porosity was found with the temperature above 950$^{\circ}C$ Reducing the grit size at the constant volume fraction of abrasive grits showed an increase in the total porosity at whole sintering temperature. On the contrary. it was observed that increasing the volume fraction of abrasive grits with a same size showed the increased open porosity simultaneously with decreased closed porosity at whole sintering temperature.

• 한국세라믹학회지
• /
• 제40권6호
• /
• pp.572-576
• /
• 2003

$UO_2$-20 wt% CeO$_2$ 소결 펠렛의 밀도에 따른 개/폐 기공도, 기공의 크기 및 그 분포 그리고 기공의 형태를 조사하였다. 이론 소결밀도 약 96% 이상에서는 기공도는 개기공이 거의 없는 폐기공으로 나타났다. 반면에 기공크기 분포는 소결밀도에 관계없이 bimodal 형태를 보이나, 소결밀도가 증가할수록 기공 개수만 적게 나타났다. 기공의 형태는 소결밀도가 증가할수록 불규칙한 형태에서 둥근 형태로 바뀌었다.

• Nuclear Engineering and Technology
• /
• 제34권5호
• /
• pp.433-435
• /
• 2002

The relation between sintered densities and porosities in UO$_2$ pellets is investigated. The open porosity decreases linearly up to about 95% T.D.,(theoretical density) as the sintered density increases whereas, above 96% T.D., sintered UO$_2$ pellets do not have any open pores. The fraction of open porosity to the total porosity also decreases linearly as the sintered density increases, though the slope is lower than that of open porosity and, above 95% T.D., the fraction decreases rapidly to approach a zero.

• Coupled systems mechanics
• /
• 제9권6호
• /
• pp.499-519
• /
• 2020

The effect of porosity on the thermo-mechanical behavior of simply supported functionally graded plate reposed on the Winkler-Pasternak foundation is investigated analytically in the present paper using new refined hyperbolic shear deformation plate theory. Both even and uneven distribution of porosity are taken into account and the effective properties of FG plates with porosity are defined by theoretical formula with an additional term of porosity. The present formulation is based on a refined higher order shear deformation theory, which is based on four variables and it still accounts for parabolic distribution of the transverse shearing strains and stresses through the thickness of the FG plate and takes into account the various distribution shape of porosity. The elastic foundation is described by the Winkler-Pasternak model. Anew modified power-law formulation is used to describe the material properties of FGM plates in the thickness direction. The closed form solutions are obtained by using Navier technique. The present results are verified in comparison with the published ones in the literature. The results show that the dimensionless and stresses are affected by the porosity volume fraction, constituent volume fraction, and thermal load.

• Steel and Composite Structures
• /
• 제45권5호
• /
• pp.697-713
• /
• 2022

In the context of the finite elements method, the dynamic behavior of porous functionally graded double wishbone vehicle suspension structural system incorporating joints flexibility constraints under road bump excitation is studied and analyzed. The functionally graded material properties distribution through the thickness direction is simulated by the power law including the porosity effect. To explore the porosity effects, both classical and adopted porosity models are considered based on even porosity distribution pattern. The dynamic equations of motion are derived based on the Hamiltonian principle. Closed forms of the inertia and material stiffness components are derived. Based on the plane frame isoparametric Timoshenko beam element, the dynamic finite elements equations are developed incorporating joint flexibilities constraints. The Newmark's implicit direct integration methodology is utilized to obtain the transient vibration time response under road bump excitation. The presented procedure is validated by comparing the computational model results with the available numerical solutions and an excellent agreement is observed. Obtained results show that the decrease of porosity percentage and material graduation tends to decrease the deflection as well as the resulting stresses of the control arms thus improving the dynamic performance and increasing the service lifetime of the control arms.

• Journal of the Korean Wood Science and Technology
• /
• 제47권1호
• /
• pp.8-20
• /
• 2019

This study was conducted to analyze the pore structure of Yellow poplar. Cross-sectional surfaces of heartwood and sapwood of Yellow poplar (Liriodendron tulipifera) were observed by SEM, and the true density of the heartwood, intermediate wood and sapwood were measured by gas pycnometery, while gas permeability and pore size of heartwood, intermediate wood and sapwood were measured by capillary flow porometery. The pores were classified as through pore, blind pore and closed pore. It was determined that the permeability was increased due to the content and size of through pore being increased although the total porosity of specimen showed slight difference from pith to bark. The content of through pore porosity was 33.754 % of heartwood and 47.810 % of sapwood, showed an increasing trend from pith to bark, however, those for the blind pore porosity and closed pore porosity were 27.890 % and 19.492 % for heartwood and 19.447 % and 4.660 % for sapwood, showed a decreasing trend from pith to bark. The max pore size of specimens was increased by about 5 times from $5.927{\mu}m$ to $31.334{\mu}m$, and mean flow pore size was increased by about 315 times from $0.397{\mu}m$ to $12.437{\mu}m$ from pith to bark.

• 한국해양공학회지
• /
• 제13권3B호
• /
• pp.29-37
• /
• 1999

Ventilation of the marine engine room is very important for the health of the workers as well as the normal operation of machines. To find proper ventilation conditions of this engine room, numerical simulation with standard k-${\epsilon}$ model was carried out. In the present study, the marine engine room is separated to two floors with porus horizontal partition and considered as a closed space with a heat source and forced ventilation ducts. The porosity of horizontal partition is found to be important. For the engine room with 2 supply ports & 2 exhaust ports, the increasing of the porosity of horizontal partition is effective to reduce the recirculation flow zone in the second floor. When the engine room is ventilated with three supply air ports & one exhaust port, the increasing of the porosity of horizontal partition is effective to reduce the recirculating flow zone in the exhaust air area, but there is a possibility of local extreme heating at the lower side of engine near bottom.

• International Journal of Advanced Culture Technology
• /
• 제10권3호
• /
• pp.339-345
• /
• 2022

In this paper, the effect of porosity on the acoustic phase velocity of the 3D printed Kelvin closed-cell structure was investigated using the spectral phase analysis. Since Kelvin cells bring about the large amount of scattering, acoustic pulses in ultrasonic measurements undergoes a distortion of waveforms due to the dispersion effect. In order to take account on the dispersion, mathematical expressions for calculating the phase velocity of longitudinal waves propagating normal to the plane of the Kelvin structure are suggested by introducing a complex wave number based on Fourier transform. 3D Kelvin structure composed of identical unit-cells, a polyhedron of 14 faces with 6 quadrilateral and 8 hexagonal faces, was developed and fabricated by 3D CAD and 3D printer to represent the micro-structure of porous materials such as aluminum foam and cancellous bone. Total nine samples of 3D Kelvin structure with different porosity were made by changing the thickness of polyhedron. Ultrasonic pulse of 1MHz center frequency was applied to the Kelvin structures for the measurement of the phase velocity of ultrasound using the TOF(time-of-flight) and the phase spectral method. From the experimental results, it was found that the acoustic phase velocity decreased linearly with the porosity.

• 한국세라믹학회지
• /
• 제52권6호
• /
• pp.473-478
• /
• 2015

Green bodies of earthenware tile were prepared from a mixture of earthenware tile powder and SiC as forming agents by applying a conventional process. Granule powder for tile samples was prepared using the spray drying method with commercial earthenware raw material with a quantity of SiC of 0.3 wt%. The applied pressure was $250kg{\cdot}f/m^2$ and the firing temperature was $1050-1200^{\circ}C$. The effects of the SiC particle size and sintering temperature on the open porosity and total porosity were investigated and the correlative mechanism was also discussed. While total porosity was not significantly changed by decreasing the SiC particle size, the open porosity showed a gradual decrease, which represents an increase of the closed porosity. As the sintering temperature increased, coarsening was made among the pores due to excessive oxidation. The volume shrinkage and bending strength were demonstrated for the sintered tile samples. The sintered bulk density was also measured to determine the weight reduction value.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.600-603
• /
• 2011

The microstructure of particle stabilized wet foams can be tailored by using parameters including the amphiphile concentration, contact angle, and surface tension. The influence of these parameters on the porosity is satisfactorily described in terms of a combined influence of the contact angle and surface tension of the initial suspensions that are directly affected by the amphiphile concentration. The resulting macroporous structures exhibited a total porosity of 82%. The foam cells were predominantly closed due to the air bubbles of the original wet foams being completely covered.