• 화약ㆍ발파
• /
• 제42권2호
• /
• pp.29-41
• /
• 2024

세계 성장에 따른 금속 광물의 수요 증가와, 지속된 지표 부근의 광물 개발로 인해 고심도 광산에 존재하는 광석을 안전하고 효율적으로 채굴하는 방법이 필요하다. 고심도 광산에서는 공동 주변에 집중되는 응력이 증가하며, 이로 인해 촉발지진이나 록버스트와 같은 문제가 발생할 수 있다. 또한 심부에 위치한 단층에 발파로 인한 에너지가 전달되면 단층의 미끄러짐으로 인해 지진이 발생할 수 있으며 이와 같은 사고를 제어하는 것이 고심도 광산 채광법의 핵심이다. 본 기술보고에서는 고심도 광산에서 채광 시 발생 가능한 사고를 제어하고, 생산성을 높일 수 있는 UCB(Underhand Closed Bench) 채광법에 대해 소개하고자 한다.

• 대한두개안면성형외과학회지
• /
• 제13권2호
• /
• pp.104-110
• /
• 2012

Purpose: Who may dare to state that optimal choice of treating nasal bone fracture is closed reduction? Few decades of authors' experience in nasal bone fracture has lead to believe that more active and assertive approach in nasal bone fracture by performing simultaneous lateral osteotomy may be applied in proper indications to acquire more accurate reduction and cosmetically satisfying result. Methods: From May 2008 to October 2009, among 241 nasal bone fracture patients, 20 patients underwent simultaneous lateral osteotomy with nasal bone fracture reduction. Followed by rigid septal correction, nasal cavity is packed to stabilize the fracture segment for safer osteotomy. Through intranasal incision, in selected cases of difficult reduction or for cosmetic purposes, various types of lateral osteotomy was performed corresponding to the fracture anatomy, conditions of the nasal cavity. Postoperative nasal packing was retained for one week and nasal dorsum splint for 3 weeks. Results: Lateral osteotomy was utilized for difficult cases of closed reduction, for correction of wide nose, hump and deviation in 9, 5, 2, and 4 cases, respectively. Patient satisfaction was scaled 90% in satisfaction and moderate in 10% (2 cases), complaining of mild nasal tip deviation. Physicians detected 2 cases of apparent deformity with patient recognition; one patient with mild step deformity at the osteotomy site and the other patient with minimal implant mobility. Conclusion: By accompanying profound understanding of the fracture anatomy, more active and assertive approach in nasal fracture reduction can be coincide with simultaneous lateral osteotomy to reduce the rate of secondary deformity and to obtain more cosmetically satisfying result.

• 대한치과보철학회지
• /
• 제59권4호
• /
• pp.459-468
• /
• 2021

중증 근무력증을 가지고 있는 환자의 경우 구강 내 근육 및 신경계가 적절히 조정되지 않아 의치 제작 및 유지가 어렵다. 또한 과도하게 확장되거나 두꺼운 의치는 근육에 자극을 주어 근무력 증상을 유발할 수 있으므로 이를 고려하여 의치 제작을 해야 한다. 본 증례에서는 개구 제한을 가진 중증 근무력증을 가진 환자에서 폐구 인상법을 이용하여 의치를 제작하였다. 폐구인상법을 이용하여 환자가 가지고 있는 저작압 및 근육의 움직임을 재현하고 이를 통해 구강 기능 운동시 구강 내 근육에 자극이 적고 적절한 유지와 안정을 갖는 임플란트 유지 피개의치를 제작하였다.

• 대한두개안면성형외과학회지
• /
• 제22권6호
• /
• pp.319-323
• /
• 2021

Background: Prophylactic antibiotics are used to prevent surgical wound infection; however, proper indications must be followed with careful consideration of the risks and benefits, especially in clean or clean-contaminated wounds. Nasal bone fractures are the most common type of facial bone fracture. The most common method for treating nasal bone fracture is closed reduction, which is performed inside the nasal cavity without an incision. The purpose of this study was to determine the need for antibiotic use in the closed reduction of nasal bone fractures. Methods: A retrospective study was conducted using data from the National Insurance Service Ilsan Hospital of the Republic of Korea between 2016 and 2018. The records of patients who underwent closed reduction of nasal bone fracture were reviewed and classified according to sex, age, comorbidities, perioperative antibiotic usage, postoperative complications, nasal packing, anesthesia type, surgeon's specialty, and operation time. Results: Among the 373 patients studied, the antibiotic prescription rate was 67.3%. Just 0.8% of patients were prescribed preoperative antibiotics only, 44.0% were prescribed postoperative antibiotics only, and 22.5% were prescribed both preoperative and postoperative antibiotics. There were no cases that satisfied the definition of "surgical site infection." Furthermore, 2.1% of infection-related complications (e.g., mucosal swelling, synechia, and anosmia) occurred only in the antibiotic usage group. The use of nasal packing, anesthesia type, and surgeon's specialty did not show any difference in infection-related complication rates. Conclusion: According to the study findings, the routine use of perioperative antibiotics is not recommended in uncomplicated nasal bone fracture surgery.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1071-1075
• /
• 2003

In a closed square cavity filled with a liquid, a cooled the upper horizontal wail and a heated the lower horizontal wall, the flow isn't generated under the ground-based condition when Rayleigh number is lower than 1700. In such case the flow phenomena near an air bubble under a cooled horizontal wall were investigated. The temperature and the flow fields were studied by using the Thermo-sensitive Liquid-Crystal and the image processing. The qualitative analysis for the temperature and the flow fields were carried out by applying the image processing technique to the original data. Injecting bubble at the center point of upper cooled wall, the symmetry shape of two vortexes near an air bubble was observed. The bubble size increased, the size of velocity and the magnitude of velocity increased. In spite of elapsed time, a pair of two vortexes was the unique and steady-state flow in a square cavity and wasn't induce to the other flow in the surround region.

• 소성∙가공
• /
• 제17권8호
• /
• pp.600-606
• /
• 2008

In closed-die hot forging, a billet is formed in dies such that the flow of metal from the die cavity is restricted. Some parts can be forged in a single set of dies, whilst others, due to shape complexity and material flow limitations, must be shaped in multi sets of dies. The purpose of a performing operation is to distribute the volume of the parts such that material flow in the finisher dies will be sound. This study focused on the design of preforms, flash thickness and land width by theoretical calculation and finite element analysis, to manufacture the super hot forging product, 70MC type piston crown used in marine engine. The optimal design of preforms by the finite element analysis and the design experiment achieves adequate metal distribution without any defects and guarantees the minimum forming load and fully filling of the cavity of the die for producing the large piston crown. The maximum loads obtained by finite element analysis are compared with the results of experiments. The loads of the analysis have good agreements with those of the experiment. Results obtained using DEFORM-2D enable the designer and manufacturer of super hot forging dies to be more efficient in this field.

• 한국임상수의학회지
• /
• 제20권3호
• /
• pp.323-327
• /
• 2003

This study has been conducted to compare the efficacy of sodium carboxymethylcellulose (SCMC) and hyaluronic acid (HA) on prevention of adhesion after artificial wound was induced in intestine. 1 % SCMC and 0.3% HA solution and saline solution were respectively administered to abdominal cavity. Each of the three groups consists of 11 rats. The abdominal cavity of each rat was coated with 2 ml of the allocated solution just after the abdomen was cut open, and it was coated with each solution of 1 ml before abrasion were caused on the cecum, the ascending colon and the transverse colon. Then, an additional 1 ml solution was injected before the abdomen was closed. On day 14 after the operation, each adhesion formation was evaluated at the score of 0-4. The HA group and SCMC group showed significantly lower adhesion scores than control group in all regions(P< 0.05). The adhesion scores of ascending colon, transverse colon and no abrasion region of the viscera showed little difference between HA group and SCMC group(P< 0.05), but the effect of adhesion reduction showed higher tendency in the HA group than the SCMC. The adhesion score of the cecum was significantly lower in HA group than SCMC group(P< 0.05). In conclusion, the SCMC solution and HA solution were effective on prevention of abdominal adhesion resulting from the celiotomy. Among of them, the HA solution could be more effective on prevention of adhesion than SCMC solution.

• Multiscale and Multiphysics Mechanics
• /
• 제1권3호
• /
• pp.225-231
• /
• 2016

The formation of silicon-on-nothing (SON) structure during an annealing process from the silicon substrate including the trench structures has been considered as an effective technique to construct the structure that has an empty space under the closed flat surface. Previous studies have demonstrated the mechanism of the formation of SON structure, which is based on the surface diffusion driven by the minimization of their surface energy. Also, it has been fragmentarily shown that the morphology of SON structure can be affected by the initial design of trench (e.g., size, number) and the annealing conditions (e.g., temperature, pressure). Based on the previous studies, here, we report a comprehensive study for the design of the cavity-embedded structure (i.e., SON structure). To do this, a dynamic model has been developed with the phase field approach. The simulation results represent that the morphology of SON structures could be detailedly designed, for example the position and thickness of cavity, the thickness of top and bottom layer, according to the design parameters. This study will give us an advantage in the effective design of SON structures.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.199-203
• /
• 1995

The technology of Semi-Solid Forging (SSF) has been actively developed to fabricate near-net- shape products using light and hardly formable materials, the SSF process is composed of slug heating, forming, compression holding and ejecting step. After forming step in SSF, the slug is compressed during a certain holding time in order to be completely filled in the die cavity and be accelerated in solidification rate. The compression holding time that can affect mechanical properties and shape of products is important to make decision, where it is necessary to find overall hert transfer coefficeient properly which has large effect on heat transfer between slug and die. This paper presents the procedure to predict compression holding time of octaining the final shaped part with information of temperature and solid fraction for a cylindrical slug at compression hoiding step in closed-die compression process using heat transfer analysis considering latent heat by means of finite element method. The influence of the predicted compression hoiding time on mechanical properties of products is finally investigated by experiment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.26-30
• /
• 2003

Since the dimension of cold forged part is larger than the cavity size of forging die, the difference results from the various features, such as, the elastic characteristics of die and workpiece, thermal influences, and machine-elasticity. All of these factors should be considered to get more accurate prediction of the dimension of forged part. In this paper, severe FE techniques are proposed to improve the prediction accuracy of dimension for cold forged part. To validate the importance of the above mentioned factors, and the estimated results are compared with the experimental results. The used model is a closed die upsetting of cylindrical billet. The calculated dimensions are well coincided with .the measured values based on the proposed techniques. The proposed techniques have put two simple but important points into Fe simulation. One is the separation of forging stages into 3 steps, from a loading through punch retraction to ejecting stage. The other is the dimensional change, according to the temperature changes due to the deformation. The FE analysis could predict the dimension of cold forged part within the $10{\mu}m$, based on the more realistic consideration.