• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.899-905
• /
• 2017

This paper presents a reference-less dual loop clock and data recovery (CDR) circuit that supports a data rate of 2.496 Gb/s for the mobile industry processor interface (MIPI) M-PHY. An adaptive loop bandwidth scheme is used to implement the fast lock time maintaining a low time jitter. To this scheme, the proposed CDR consists of two loops for a frequency locked loop and a phase locked loop. The proposed 2.496 Gb/s reference-less dual loop CDR is designed using a 65 nm CMOS process with 1.2 V supply voltage. The simulated peak-to-peak jitter of output clock is 9.26 ps for the input data of 2.496 Gb/s pseudo-random binary sequence (PRBS) 15. The active area and power consumption of the implemented CDR are $470{\times}400{\mu}m^2$ and 6.49 mW, respectively.

• ETRI Journal
• /
• v.34 no.1
• /
• pp.35-43
• /
• 2012

This paper presents a delay-locked-loop-based clock and data recovery (CDR) circuit design with a nB(n+2)B data formatting scheme for a high-speed serial display interface. The nB(n+2)B data is formatted by inserting a '01' clock information pattern in every piece of N-bit data. The proposed CDR recovers clock and data in 1:10 demultiplexed form without an external reference clock. To validate the feasibility of the scheme, a 1.7-Gbps CDR based on the proposed scheme is designed, simulated, and fabricated. Input data patterns were formatted as 10B12B for a high-performance display interface. The proposed CDR consumes approximately 8 mA under a 3.3-V power supply using a 0.35-${\mu}m$ CMOS process and the measured peak-to-peak jitter of the recovered clock is 44 ps.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.28-33
• /
• 2006

An integrated 3.125Gbps clock and data recovery (CDR) circuit is presented. The circuit does not need a reference clock. It has a phase and frequency detector (PFD), which incorporates a bang-bang type 4X oversampling PD and a rotational frequency detector (FD). It also has a ring oscillator type VCO with four delay stages and three zero-offset charge pumps. With a proposed PD and m, the tracking range of 24% can be achieved. Experimental results show that the circuit is capable of recovering clock and data at rates of 3.125Gbps with 0.18 um CMOS technology. The measured recovered clock jitter (p-p) is about 14ps. The CDR has 1.8volt single power supply. The power dissipation is about 140mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.36-42
• /
• 2008

40Gb/s CMOS Clock and Data Recovery circuit design for optical serial link is proposed. The circuit generates 8 multiphase clock using LC tank PLL and controls the phase between the clock and the data using the $2{\times}$ oversampling Bang-Bang PD. 40Gb/s input data is 1:4 demultiplexed and recovered to 4 channel 10Gb/s outputs. The design was progressed to separate the analog power and the digital power. The area of the chip is $2.8{\times}2.4mm^2$ for the inductors and the power dissipation is about 200mW. The chip has been fabricated using 0.18um CMOS process. The measured results show that the chip recovers the data up to 9.5Gb/s per channel(Equivalent to serial input rate of up to 38Gb/s).

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.2
• /
• pp.72-77
• /
• 2009

In this paper, a 3.2Gb/s clock and data recovery (CDR) circuit for a high-speed serial data communication without the reference clock is described This CDR circuit consists of 5 parts as Phase and frequency detector(PD and FD), multi-phase Voltage Controlled-Oscillator(VCO), Charge-pumps (CP) and external Loop-Filter(KF). It is adapted the PD and FD, which incorporates a half-rate bang-bang type oversampling PD and a half-rate FD that can improve pull-in range. The VCO consists of four fully differential delay cells with rail-to-rail current bias scheme that can increase the tuning range and tuning linearity. Each delay cell has output buffers as a full-swing generator and a duty-cycle mismatch compensation. This materialized CDR can achieve wide pull-in range without an extra reference clock and it can be also reduced chip area and power consumption effectively because there is no additional Phase Locked- Loop(PLL) for generating reference clock. The CDR circuit was designed for fabrication using 0.18um 1P6M CMOS process and total chip area excepted LF is $1{\times}1mm^2$. The pk-pk jitter of recovered clock is 26ps at 3.2Gb/s input data rate and total power consumes 63mW from 1.8V supply voltage according to simulation results. According to test result, the pk-pk jitter of recovered clock is 55ps at the same input data-rate and the reliable range of input data-rate is about from 2.4Gb/s to 3.4Gb/s.

• ETRI Journal
• /
• v.21 no.3
• /
• pp.1-5
• /
• 1999

A clock and data recovery circuit with a phase-locked loop for 10 Gb/s optical transmission system was realized in a hybrid IC form. The quadri-correlation architecture is used for frequency-and phase-locked loop. A NRZ-to-PRZ converter and a 360 degree analogue phase shifter are included in the circuit. The jitter characteristics satisfy the recommendations of ITU-T. The capture range of 150 MHz and input voltage sensitivity of 100 mVp-p were showed. The temperature compensation characteristics were tested for the operating temperature from -10 to $60^{\circ}C$ and showed no increase of error. This circuit was adopted for the 10 Gb/s transmission system through a normal single-mode fiber with the length of 400 km and operated successfully.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.21-26
• /
• 2008

In this paper, a novel 622Mbps burst-mode clock and data recovery (CDR) circuit is proposed for passive optical network (PON) applications. The CDR circuits are implemented with 0.35um CMOS process technology. Locking dynamics is accomplished with instantaneous feature and data are sampled at an optimal timing. This is realized by seven different delay configurations, which are generated from precisely-controlled delay buffers. The experimental results show that the proposed CDR circuits are operating as expected, recovering an incoming 622Mbps burst-mode input data without errors.

• ETRI Journal
• /
• v.44 no.5
• /
• pp.859-874
• /
• 2022

This paper presents a low-power and lightweight human body communication (HBC) receiver with an embedded dummy electrode for improved signal acquisition. The clock data recovery (CDR) circuit in the receiver operates with a low supply voltage and utilizes a clock phase inversion scheme. The receiver is equipped with a main electrode and dummy electrode that strengthen the capacitive-coupled signal at the receiver frontend. The receiver CDR circuit exploits a clock inversion scheme to allow 0.9-V operation while achieving a shorter lock time than at 3.3-V operation. In experiments, a receiver chip fabricated using 130-nm complementary metal-oxide-semiconductor technology was demonstrated to successfully receive the transmitted signal when the transmitter and receiver are placed separately on each hand of the user while consuming only 4.98 mW at a 0.9-V supply voltage.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.97-103
• /
• 2014

In this paper, a clock-data recovery using a 1/8-rate phase detector is proposed. The use of a conventional full or half-rate phase detector requires relatively higher frequency of a recovered clock, which is a burden on the design of a sampling circuit and a VCO. In this paper, a 1/8-rate phase detector is used to lower the frequency of the recovered clock and a linear equalizer is used as a input circuit of a phase detector to reduce the jitter of the recovered clock. A test chip fabricated in a 0.13-${\mu}m$ CMOS process is measured at 1.5-GHz for a 3-Gb/s PRBS input and 1.2-V power supply.

• ETRI Journal
• /
• v.33 no.5
• /
• pp.752-758
• /
• 2011

This paper presents a clock and data recovery circuit that supports dual data rates of 5.4 Gbps and 3.24 Gbps for DisplayPort v1.2 sink device. A quarter-rate linear phase detector (PD) is used in order to mitigate high speed circuit design effort. The proposed linear PD results in better jitter performance by increasing up and down pulse widths of the PD and removes dead-zone problem of charge pump circuit. A voltage-controlled oscillator is designed with a 'Mode' switching control for frequency selection. The measured RMS jitter of recovered clock signal is 2.92 ps, and the peak-to-peak jitter is 24.89 ps under $2^{31}-1$ bit-long pseudo-random bit sequence at the bitrate of 5.4 Gbps. The chip area is 1.0 mm${\times}$1.3 mm, and the power consumption is 117 mW from a 1.8 V supply using 0.18 ${\mu}m$ CMOS process.