• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.4
• /
• pp.263-266
• /
• 2017

In this study, the characteristics of anti-pollution coatings on glass substrates through annealing treatment were investigated. To investigate the change of properties by coating method and number of annealing treatment, after the anti-pollution coating was performed on the surface of glass substrate in three ways, the annealing treatment was performed by setting three kinds of annealing treatment conditions. The annealing treatment method is a torch using gas, which is advantage in that it can be installed directly on the site in an easy way compared with a annealing treatment process which is generally difficult. The anti-pollution properties, contact angle, transmittance, hardness, and adhesion of films on glass substrate were measured under 9 conditions of combination of coating methods and annealing treatment conditions. It was confirmed that as the number of annealing treatment increases, the anti-pollution property of the film synthesized on glass substrate becomes better.

• Journal of the Korean Society of Costume
• /
• v.55 no.8 s.99
• /
• pp.154-160
• /
• 2005

For the purpose of standardization and practicability of natural dyeing, the mordanting and dyeing properties of Puerariae Radix was studied. Appropriate extraction, dyeing and mordanting condition of Puerariae Radix were determined, and the effect of mordanting method on dye uptake and color fastness of dyed fabric was investigated. The maximum absorbance of Puerariae Radix solution was at 290nm and 301nm. The pH effect was stable in the color difference changes. The optimum temperature to extract Puerariae Radix was during 1 hour in loot. The effective dyeing temperature and time of silk were 80$\~$ 100$^{circ}C$, 1hour. The silk fabrics dyed with Puerariae Radix appeared yellow-brown. US value of dyeing fabrics was increased by Fe, and Cu mordant treatment. Mordanting treatment method affected color change of the dyed silk. In the case of Puerariae Radix light fastness of appeared more than 2-5 grades by mordant treatment. Perspiration fastness of appered more than 4 grades by Al, Sn, Cr mordant treatment. Fastness of abrasion and dry-cleaning appered more than 4-5 grades. These fastness improvement were generally effective for mordant treatment, specially Al, Sn, Cr.

• Journal of the Korean Applied Science and Technology
• /
• v.23 no.1
• /
• pp.37-44
• /
• 2006

Solvent-free low foaming scouring agents (LFSC) were prepared by blending of 2-ethylhexylaminoethyl sulfate (2-EHAS), POE(10) octadecylbenzyl- ammonium chloride (POBAC) and Sedlan FF-200 (FF-200). As the results of several tests, 2-EHAS/POBAC/FF-200/water (8g/12g/20g/60g) mixture (LFSC-5) showed good cleaning power, penetrating ability and stability to alkali, and gave less problem in water pollution. The foaming power of LFSC-5 measured by Ross and Miles method was 8mm foam height immediately after foaming, and that measured by Ross and Clark method was less than 300mm foam height at $30^{\circ}C$, and 18mm at $80^{\circ}C$. As a result, LFSC-5 proved a good low foaming scouring agent for fiber.

• Corrosion Science and Technology
• /
• v.17 no.3
• /
• pp.123-128
• /
• 2018

The fabrication of a controlled surface is of great interest because it can be applied to various engineering facilities due to the various properties of the surface, such as self-cleaning, anti-bio-fouling, anti-icing, anti-corrosion, and anti-sticking. Controlled surfaces with micro/nano structures were fabricated using an ion beam focused onto a polypropylene (PP) surface with a fluoridation process. We developed a facile method of fabricating hydrophobic surfaces through ion beam treatment with argon and oxygen ions. The fabrication of low surface energy materials can replace the current expensive and complex manufacturing process. The contact angles (CAs) of the sample surface were $106^{\circ}$ and $108^{\circ}$ degrees using argon and oxygen ions, respectively. X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR) spectroscopy were used to determine the chemical composition of the surface. The morphology change of the surfaces was observed by scanning electron microscopy (SEM). The change of the surface morphology using the ion beam was shown to be very effective and provide enhanced optical properties. It is therefore expected that the prepared surface with wear and corrosion resistance might have a considerable potential in large scale industrial applications.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.1
• /
• pp.85.2-85.2
• /
• 2012

In this paper, we introduce the 3D modeling of the coronal magnetic field in the solar active region by extrapolating from the 2D observational data numerically. First, we introduce a nonlinear force-free field (NLFFF) extrapolation code based on the MHD-like relaxation method implementing the cleaning a numerical error for Div B proposed by Dedner et al. 2002 and the multi-grid method. We are able to reconstruct the ideal force-free field, which was introduced by Low & Lou (1990), in high accuracy and achieve the faster speed in the high-resolution calculation (512^3 grids). Next we applied our NLFFF extrapolation to the solar active region NOAA 10930. First of all, we compare the 3D NLFFF with the flare ribbons of Ca II images observed by the Solar Optical Telescope (SOT) aboard on the Hinode. As a result, it was found that the location of the two foot-points of the magnetic field lines well correspond to the flare ribbon. The result indicates that the NLFFF well capture the 3D structure of magnetic field in the flaring region. We further report the stability of the magnetic field by estimating the twist value of the field line and finally suggest the flare onset mechanism.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.9
• /
• pp.1301-1307
• /
• 2002

This paper surveys the mordanting and dyeing properties of Rubia akane Nakai appropriate extraction, dyeing and mordanting conditions of Rubia akane Nakai were determined, and the effect of mordanting method on dye uptake and color fastness of the dyed fabric was investigated. The optimum temperature to extract Rubia akane Nakai was during 1 hour in 8$0^{\circ}C$. The effective dyeing temperature and time of silk were 8$0^{\circ}C$, 1hour. The silk fabrics dyed with purpurin appeared red color, with alizarine appeared yellow-brown and with Rubia akane Nakai appeared yellow orange. K/S value of the dyeing fabrics was increased by pre-mordanting treatment. Mordant as Sn and Fe was better than anything else in K/S value. Mordanting treatment method affected color change of the dyed silk. In the case of Rubia akane Ntkai light fastness was increased by Fe and Al mordant treatment, Perspiration fastness of Rubia akane Nakai appeared more than 3 grades geneally. Fastness of abrasion and dry-cleaning appeared mon than 4～5 grades and these fastness improvement were generally effective for post-mordanting treatment.

• Journal of Hydrogen and New Energy
• /
• v.25 no.2
• /
• pp.145-150
• /
• 2014

This study investigates the preparation of anti-reflective (AR) coating film to improve the efficiency of solar cell. The AR coating film was successfully obtained by dip-coating with AR coatings prepared by sol-gel method. Fluoroalkylsilane was additionally introduced into the coatings to give the self-cleaning effect of AR coating film. We performed the abrasion test, pencil scratch hardness test and cross-cut test to identify the mechanical strength of AR coating film. As the results, the transmittance of AR coating films with 9.07, 18.13 and 27.20 of IPA/MTMS molar ratios were 93.1, 93.6 and 95.3%, respectively. The water contact angle and transmittance of AR coating film increased by the introduction of hydrophobicity. The prepared AR coating film shows the high level of abrasion, hardness and adhesion. The IPA/MTMS molar ratio of 27.20 and the withdrawing speed range of 0.20 ~ 0.28cm/sec are the optimal coating condition in terms of the transmittance and mechanical strength of AR coating film.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1251-1256
• /
• 2014

The use of lubrication oil is of many purposes and one among them is to drive the engine mounted on a ship. Hence the supply of clean lubrication oil is important. And an oil purifier is one of key components in marine diesel engines. At present, the element type full-flow oil filter has been widely used for cleaning the engine oil. The self-driven centrifugal oil purifier is a device which is used to remove the impurities in lubrication oil using a jet flow. The flow characteristics and the physical behaviors of particles in this self-driven oil purifier were investigated numerically and the filtration efficiencies were evaluated. For calculations, a Computational Fluid Dynamics method is used and the Shear Stress Transport turbulence model has been adopted. The Multi Frames of Reference method is used to consider the rotating effect of the flows. The influence of centrifugal forcehas been numerically investigatedto improve filtration efficiency of tiny particles. As a result of this research, it was found that the particle filtration efficiency using the only center axis rotating and outer wall rotating system are higher than that of the fully rotating system in the self-driven oil purifier.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.438-446
• /
• 2003

This paper presents the development of the remotely operated decontamination systems for use in a highly radioactive zone of the DUPIC Fuel Development facility of the Irradiated Material Examination Facility at the Korea Atomic Energy Research Institute. The remotely operated decontamination systems were designed to completely eliminate human interaction with hazardous radioactive contaminants. These decontamination systems are mainly classified into three systems depending on the task environment - a fabrication equipment decontamination system, a hot-cell floor decontamination system, and an isolation room floor decontamination system. A decontamination system for contaminated fabrication equipment utilizes dry ice pellet blasting method to decontaminate contaminated surface of the equipment. The decontamination systems for the hot-cell floor and isolation room floor employ a vacuum cleaning method to decontaminate the contaminated floor and collect loose dry spent nuclear fuel debris and other radioactive waste placed on the floor. The human operator from the out-of-cell performs a series of decontamination tasks remotely by manipulating decontamination systems located in-cell via a handcontroller with the aid of vision feedback information. The environmental, functional and mechanical design considerations, control system and capabilities of the remotely operated decontamination systems at a high radioactive environment are also described.

• Journal of Environmental Science International
• /
• v.15 no.10
• /
• pp.913-918
• /
• 2006

Despite the wide distribution of air pollutants, the concentrations of indoor air pollutants may be the dominant risk factor in personal exposure due to the fact that most people spend an average of 80% of their time in enclosed buildings. Researches for improvement of indoor air quality have been developed such as installation of air cleaning device, ventilation system, titanium dioxide$(TiO_2)$ coating and so on. However, it is difficult to evaluate the magnitude of improvement of indoor air quality in field study because indoor air quality can be affected by source generation, outdoor air level, ventilation, decay by reaction, temperature, humidity, mixing condition and so on. In this study, evaluation of reduction of formaldehyde and nitrogen dioxide emission rate in indoor environments by $TiO_2$ coating material was carried out using mass balance model in indoor environment. we proposed the evaluation method of magnitude of improvement in indoor air quality, considering outdoor level and ventilation. Since simple indoor concentration measurements could not properly evaluate the indoor air quality, outdoor level and ventilation should be considered when evaluate the indoor net quality.