• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.6
• /
• pp.721-728
• /
• 2017

In this work, an one-dimensional analysis on spontaneous combustion in a coal stockpile was conducted using a commercial software $gPROMS^{(R)}$ based on assumption suggested by Arioy and Akgun. According to them, it is assumed that there is temperature difference between the surface of coal particle and the gas surrounded around the particle, and it is also assumed that the velocity of the gas is constant and thus oxygen is fed to the stockpile with same velocity. The higher temperature zone is formed to the surface of the coal stockpile at the initial phase and it became deepen as time is taken. Finally it was found that the temperature difference between coal particle and the gas was calculated as $57^{\circ}C$ and spontaneous combustion have not been occurred during 6 months since coal was piled in the stock.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.183-184
• /
• 2015

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.4
• /
• pp.324-330
• /
• 2018

In this study a numerical study was conducted to show flow, temperature and gas distributions in a high temperature CO shift reactor which was designed specially for energy saving and then evaluated with the related experiment. Mole fractions of syngas at the end of the catalyst bed were predicted with various assumed pre-exponential factors, were compared with the corresponding experimental results and $10^8$ was finally selected as the value. With the selection, a base case was examined. It was calculated that the inlet duct attached asymmetrically to the CO shift reactor affects on the distribution of the upward momentum (+z directional). In addition, CO conversion ratio is achieved up to 90% in the catalyst bed and especially it reached up to 70% at the initial part of catalyst bed.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.327-328
• /
• 2015

• Clean Technology
• /
• v.22 no.4
• /
• pp.299-307
• /
• 2016

These days, coal is one of the most important energy resources used for transportation, industry, and electricity. There are two types of coal: high-rank and low-rank. Low-rank coal has a low calorific value and contains large amounts of useless moisture. The quality of low-rank coal can be increased by simple drying technology and it needs to be stabilized by hydrocarbons (e.g. palm acid oil, PAO) to prevent spontaneous combustion and moisture re-adsorption. Spontaneous combustion becomes a major problem during coal mining, storage, and transportation. It can involve the loss of life, property, and economic value; reduce the quality of the coal; and increase greenhouse gas emissions. Besides spontaneous combustion, moisture re-adsorption also leads to a decrease in quality of the coal due to its lower heating value. In this work, PAO was used for additive to stabilize the upgraded coal. The objectives of the experiments were to determine the stabilization characteristic of coal by analyzing the behavior of upgraded coal by drying and PAO addition regarding crossing-point temperature of coal, the moisture behavior of briquette coal, and thermal decomposition behavior of coal.

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.1-6
• /
• 2014

Upgrading technology has been studied for efficient utilization of low rank coal. Spray coating of heavy oil was applied on the upgrading process in order to stabilize low rank coal against spontaneous combustion. Low rank coal, which contains more than 30wt% of moisture, was upgraded to high calorific coal and stabilized by spray coating of heavy oil. It was identified that spray coating of heavy oil after drying coal is the optimum procedure of upgrading low rank coal. The experimental results show that more than 2wt% of heavy oil should be adsorbed on the coal in order to stabilize sufficiently for spontaneous combustion.

• Particle and aerosol research
• /
• v.5 no.4
• /
• pp.171-178
• /
• 2009

$PM_{2.5}$ is one of critical air pollutants due to its high absorbability of heavy metallic fumes, PAH and bacillary micro organisms. Such a fine particulate matter is often formed through various nucleation processes including condensation. This study attempts to find the nucleation behaviors of $PM_{2.5}$ arisen from coal power stations using a classical heterogeneous Fletcher's theory. The numerical simulation by C-language could approximate the nucleation process of $PM_{2.5}$ from water vapor, of which approach revealed the required energy for embryo formation and embryo size and nucleation rate. As a result of the calculation, it was found that wetting agents could affect the particle nucleation in vapor condensation. In particular, critical contact angle relates closely with the vapor saturation. Particle condensation could be reduced by lowering the angles. The wetting agents aid to decrease the contact angle and surface tensions, thereby may contribute to save the formation energy.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.341-341
• /
• 2015

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.331-332
• /
• 2015

• Fire Science and Engineering
• /
• v.33 no.2
• /
• pp.20-29
• /
• 2019

In this paper, the effect of spontaneous combustion inhibitor on the surface of coal stockpile in coal yard was investigated by numerical analysis. First, the numerical analysis method of the present study was compared with the results of the previous study by analyzing the case where the spontaneous combustion inhibitor was not applied, and the effect of preventing spontaneous combustion by various areas and positions for spraying spontaneous combustion inhibitor was analyzed. As a result, the larger the application area of the spontaneous combustion inhibitor, the more the effect of preventing spontaneous combustion by blocking the oxygen inflow into the coal stockpile, and the greater the effect of the spontaneous combustion prevention when spraying spontaneous combustion inhibitor from the bottom of the coal stockpile. Spontaneous combustion inhibitor should be sprayed effectively, considering the economic aspects, such as manufacturing cost etc.