• 한국기계가공학회지
• /
• 제16권2호
• /
• pp.81-87
• /
• 2017

The pipe connection process using a clamping ring is used for joining small pipes in the refrigerator and air-conditioner industries instead of the brazing process, which induces inevitable thermal deformation in the pipes. However, few studies have been carried out on the process to select optimal parameters in joining pipes, and studies on the relation between the process parameters of the connection and connecting force of the joint have not been conducted. In this study, the connection process of pipes with the clamping ring was modeled using the finite element method (FEM) and analyzed to obtain the contact stress distribution between the pipes with which the connecting force of the joint was estimated. Considering the characteristics of pipe connection, the process was modeled and simulated in a two-dimensional axisymmetric solution domain. With the numerical model, the effect of ring shape on the connection was studied by adding a projection to the end of a ring or changing the length of a ring. The results of the analyses revealed that the contact stress distribution could be predicted with the suggested model. The effect of the ring shape was also presented. The effect of any combination of process parameters could be easily estimated through the related analyses.

• 한국공작기계학회논문집
• /
• 제16권6호
• /
• pp.9-14
• /
• 2007

In this paper, a rotating tool clamping device was developed based on a shape memory alloy(SMA) and its feasibility as a tool holder was experimentally explored. The SMA-based device was able to alter clamping to unclamping through temperature control within 1 second. The means and repeatability(${\sigma}$) of the tool clamping force were 185.5N and 6N respectively and its drifts were less than 3% for an hour. Considering the temperature hysteresis of the SMA-based tool clamping device, it is necessary to heat the SMA ring to around $50^{\circ}C$ after tool change to obtain more clamping force.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.16-20
• /
• 2008

This paper presents the construction of micro tool clamping device using a Ni-Ti shape memory alloy(SMA) ring. Clamping force of the device is produced by elastic force of the SMA reverted to its original shape in normal temperature. Phase transformation of the SMA was realized by temperature control using a peltier element. Prototype of the SMA tool clamping device was fabricated and examined its clamping force and clamping/unclamping operation.

• 한국태양에너지학회 논문집
• /
• 제36권3호
• /
• pp.25-31
• /
• 2016

Gaskets are usually used for the sealing of flange joints. The joint is usually composed of two flanges, a ring gasket and clamping bolts. The metal ring gasket is suitable for pipe flanges, pumps and valve joints in high temperature and high pressure environments. A very high surface stress is developed between a ring type joint gasket and the flange groove when the ring type joint is bolted up in a flange. The dimensions of flanges and ring joint gaskets for the pipe sizes that are in common use are specified in the ANSI codes. However, sometimes it is necessary to make a new design for the flange joint which is not specified in the codes, as the equipment is getting larger and larger in size. This paper presents the contact behavior of Class 600 ring joint gaskets with oval and octagonal cross sections. Five different sizes of gaskets are employed in the analysis, and one of them is newly designed on the basis of analysis results obtained from existing models. Three load steps are used to find the stress, stain and contact pressure etc., and to compare the contact characteristics among the models due to the bolt clamping force and the working surface pressure. ANSYS Workbench version15 is used to conduct the finite element analysis.

• 한국공작기계학회논문집
• /
• 제17권5호
• /
• pp.70-75
• /
• 2008

This paper describes a tool-clamping/unclamping mechanism for application of a micro-spindle. The mechanism is based on one-way shape memory effect and interference-fit. The corresponding mathematical models and a few considerable design parameters are mentioned in this paper. Especially, necessary conditions for the clamping and unclamping operation are investigated through finite element analysis. The analysis results show that the differences between the diametral deformations of the tool holder in high temperature and that in low temperature are increased according to amounts of the interference. Thus the less interference between the tool-holder and the ring, the less tolerance to allow the clamping and unclamping operation because the inner diameter of the tool holder in high temperature should be smaller than the diameter of the tool shank, and that in low temperature should be larger than the diameter of the tool shank. In addition, the design for maximization of clamping force are investigated based on finite element analysis. The results show that the more amounts of the interference, the more clamping force. As the result, the interference should be considered as a important factor to maximize the tool clamping force.

• 드라이브 ㆍ 컨트롤
• /
• 제11권2호
• /
• pp.9-15
• /
• 2014

This paper deals with the issue of force synchronizing control for the clamping servomechanism of injection molding machines. Prior to the controller design, a virtual design model has been developed for the clamping mechanism with hydraulic systems. Then, a synchronizing controller is designed and combined with an adaptive feedforward control in order to accommodate the mismatches between the real plant and the linear model plant used. As a disturbance, the leakage due to the ring gap with relative motion in the cylinder has been introduced. From the robust force tracking simulations, it is shown that a significant reduction in the force synchronizing error is achieved through the use of a proposed control scheme.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 추계학술대회 논문
• /
• pp.180-186
• /
• 1996

Using carbon steel or ceramic as a shaft material of monolithic and slited insert ring clamped on it. The fitting strengths of the sgrink fitted assemblies measured from room temperature to 30$0^{\circ}C$ and following conclusions were obtained as results of this investigation. 1) The fitting condition under which the shrink fitted assemble was stronger than that using simple fit in high temperature. 2) When both material of the 30mm-diameter shaft and 55mm-diameter boss are SM45C the clamping torque is increased 2.7times as the interference increases 3 times from 20${\mu}{\textrm}{m}$ at the contact length of 6mm monolithic fit. 3) When only the material of boss is changed to STS 304 the clamping torque is increased at the rate of 37.3N.m per 1mm increase of the contact length at the interference of 50${\mu}{\textrm}{m}$ monolithic fit.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.540-541
• /
• 2002

In this paper, the performance of upidirectional and hi-directional regenerative erbium-doped fiber amplifier (EDFA) is compared. The systems are operating above laser oscillation threshold. The experimental results show that the unidirectional regenerative EDFA has a better performance than the hi-directional.

• 한국생산제조학회지
• /
• 제25권1호
• /
• pp.1-6
• /
• 2016

Micromanufacturing is a useful system for reducing energy consumption. For micromanufacturing, tool clamping and workpiece clamping are important components to realize the machining process. Therefore, a shape memory alloy (SMA) ring type tool holder is developed. In addition, this holder needs cooling and heating processes to execute the tool clamping process. This study suggests a cooling/heating device based on peltier elements. The device will be applied to the heating/cooling process of an automatic tool changer (ATC) for the SMA tool holder. This study introduces the configuration and operating principle of the proposed ATC system. The description and prototype evaluation of this system were given. Plastic bolt and aluminum block were selected to enhance the cooling performance, and the installed tool was changed in 17 s during the experiments.

• Journal of Chest Surgery
• /
• 제51권4호
• /
• pp.283-285
• /
• 2018

A 73-year-old woman who underwent combined bioprosthetic mitral valve replacement, tricuspid ring annuloplasty, and coronary artery bypass grafting 12 years previously visited our clinic due to aggravated dyspnea caused by structural valve deterioration of the mitral prosthesis. Because aortic or femoral artery cannulation and cross-clamping would have a high risk of stroke owing to severe calcification of the ascending aorta and ilio-femoral vessels, and because there was a risk of redo sternotomy due to the patent bypass grafts, a comprehensive approach including axillary artery cannulation, a minimally invasive right thoracotomy approach, and a clampless hypothermic fibrillatory arrest technique was used during redo mitral valve replacement.