• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.844-847
• /
• 2002

This paper is to investigate the wear behavior of submerged-arc clad materials by the wear test with a ball-on-disk type wear testing machine in air. The specimens were clad with Stoody105 alloy wire on a carbon steel (SM45C) substrate by submerged-arc cladding process under different welding parameters. The wear behavior of the cladding through ball-en-disk test has been studied under the wear load from 5N to 16N and sliding speed from 8cm/s to 35cm/s. The weight of the specimen loss was measured. Scanning electron micrographs of the worn surface show a layer of oxide film formed on the worn surface. Oxidation wear mechanism controls the wear process. The spalling of the oxide is caused by the repeated rubbing fatigue mechanism.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.221-224
• /
• 2004

The clad samples of five plies of sheets comprising ferritic stainless steel (STS) and aluminum (Al) were prepared by roll-cladding at $350^{\circ}C$. The evolution of strain states and textures during roll-cladding of STS430/AA3003/AA3003/AA3 003/STS430 and STS430/AA3003/STS430/AA3003/STS430 was investigated by measurements of crystallographic textures and by simulations with the finite element method (FEM). Because the deformation mainly occurs in the Al layer during roll-cladding, the present investigation was focused on the Al layers located. The stacking sequence of sheet materials in the clad samples played an important role in the evolution of strain states during roll-cladding.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.875-880
• /
• 2007

Due to increasing demands for environment-friendly railway system, bronze wires with cadmium, which is a potential environmental hazard, have been no longer permitted as messenger wire for electric railway system. One of materials being considered as the replacements is copper-clad steel conductor(CCSC), which is currently used as contact wire for high speed operation in the Japanese shinkansen. However, there have been few studies for the application as messenger wire by the CCSC. This study deals with requirements and performances of the messenger wire stranded by the CCSC, especially for high speed electric railway. And the tentative evaluation items and methods to be specified as the Korean railway standard(KRS) are proposed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 금형가공 심포지엄
• /
• pp.8-18
• /
• 1998

The effect of press warm forming in cylindrical deep drawing of stainless-aluminum clad sheet metals are examined . The temperature of die and blank holder is varied from room temperature to 20$0^{\circ}C$, while the punch is kept cooled during test to increase the fracture strength of workpiece on the punch corner area. Test materials chosen for experiments are STS304-Al050-STS304, STS304-A1050-STS430-, STS304 and Al050 metals and teflon film as a lubricant is used on both sides of a workpiece. The limit drawing ration as well as quality of drawn cups (distribution of thickness and hardness)are investigated and discussed.

• 소성∙가공
• /
• 제22권3호
• /
• pp.143-149
• /
• 2013

A new finite element model for the hydrostatic extrusion of a biaxial bar is introduced. In this model, a penalty contact algorithm, which is adopted to replace the traction boundary conditions due to the fluid in the container of the extruder, is incorporated into a consistent penalty finite element formulation for the viscoplastic deformation of a work piece during hydrostatic extrusion. Two parameters, introduced in the penalty contact algorithm in this study, a critical penalty contact pressure $P_0$ and a critical penalty contact distance $D_c$, are carefully examined for various process conditions. The proposed finite element model is applied to the hydrostatic extrusion of a Cu-clad Al bar. The extrusion loads and thickness ratios of the clad materials by the proposed model are compared in detail to values from experiments reported in the literature. Finally, it is concluded that the proposed finite element model is useful in practical implementations.

• 한국표면공학회지
• /
• 제38권2호
• /
• pp.49-54
• /
• 2005

Flexible copper clad laminates (FCCL) fabricated by sputtering has advantages in fine pitch etching and dimensional accuracy than previous casting or laminating type FCCL, But its lower adhesion is inevitable technical challenge to solve for commercializing it. Chromium (Cr) which strongly reacts with O moiety was used as tie-coating layer in order to improve low adhesion between copper (Cu) and polyimide (PI). Sputtering raw polyimide (SRPI) and casting raw polyimide (CRPI) were used as substrates at this research. PI was pretreated by plasma before sputtering, and each sample was varied with RF power and Cr thickness on sputtering. Peel strength of the FCCL on SRPI was higher than that on CRPI. Adhesion had maximum value when 10 nm of Cr was deposited on SRPI by RF power of 50 W. It seems to be by the formation of Cu-Cr-O solid solution at the metal-PI interface.

• 한국진공학회지
• /
• 제16권2호
• /
• pp.79-90
• /
• 2007

저에너지 초고속 표면 처기 이온원, 4개의 마그네트론 스퍼터 캐소드가 부착된 300 mm 폭 다목적 연성 기판 제작을 위한 부피 800 L 용량의 진공 웹코터 원형 (prototype) 장비를 설계 제작하였고, 무접착제 2층 연성 동박 적층 필림을 제작하여 성능을 평가하였다. 2 개의 터보 펌프 및 폴리콜드를 장착한 비코팅 부분인 상실부와 각각 1개씩의 터보 펌프를 사용한 표면 처리 및 코팅 부분인 하실부의 진공 배기 특성을 측정하였다. 패러데이 컵을 사용하여 대면적 이온원의 이온 전류 밀도 및 균일도를 측정하고, 스퍼터 캐소드의 자기장 분포 및 타겟 사용 효율을 조사하였다. 진공 웹코터의 성능 및 각 구성 요소의 특성 조사를 위하여 연성 기판으로는 폴리이미드 (Kapton-E) $38{\mu}m$을 사용하여 여러 가지 가스 이온에 대한표면 처리 조건에 따른 증류수의 접촉각 변화와 화학 성분의 변화를 x-선 분광학을 사용하여 조사하였다. 고밀도 2층 연성 동박 적층 필림 기판을 스퍼터-전기 도금법으로 제작하기 위하여 스퍼터 타겟으로는 Ni-Cr 및 Cu 금속을 사용하여, 각각의 증착율을 직류 전력의 변화 및 롤의 속도에 따라 조사하였고, 전기 도금으로 $9{mu}m$ 까지 동박 적층 필림을 제작한 후 접착력 및 내열성, 내화학성을 측정하여 소형 진공 웹 코터의 특성을 조사하였다.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.122-126
• /
• 2013

The surface roughness of the inner and outer surfaces of a tube is an important requirement for nuclear fuel cladding. When an inner SiC clad tube, which is considered as an advanced Pressurized Water Cooled Reactor (PWR) clad with a three-layered structure, is fabricated by Chemical Vapor Deposition (CVD), the surface roughness of the substrate, graphite, is an important process parameter. The surface character of the graphite substrate could directly affect the roughness of the inner surface of SiC deposits, which is in contact with a substrate. To evaluate the effects of the surface roughness changes of a substrate, SiC deposits were fabricated using different types of graphite substrates prepared by the following four polishing paths and heat-treatment for purification: (1) polishing with #220 abrasive paper (PP) without heat treatment (HT), (2) polishing with #220 PP with HT, (3) #2400 PP without HT, (4) polishing with #2400 PP with HT. The average surface roughnesses (Ra) of each deposited SiC layer are 4.273, 6.599, 3.069, and $6.401{\mu}m$, respectively. In the low pressure SiC CVD process with a graphite substrate, the removal of graphite particles on the graphite surface during the purification and the temperature increasing process for CVD seemed to affect the surface roughness of SiC deposits. For the lower surface roughness of the as-deposited interlayer of SiC on the graphite substrate, the fine controlled processing with the completed removal of rough scratches and cleaning at each polishing and heat treating step was important.

• 한국재료학회지
• /
• 제11권10호
• /
• pp.813-819
• /
• 2001

The microstructure and the distribution of hardness of Co and A1 alloy powder cladding layer in high carbon 9CrSi alloy steel for roll materials cladded by laser surface cladding were investigated. And, for the evaluation of soundness as the roll materials, we examined the wear resistance of the cladding materials with the wear appratus of pin on disc type. The experimental results showed that the microstructure of laser cladding layer was constituted with the clad surface layer, the alloy layer, the heat treatment layer with base metal. The wear resistance of Ni alloy Powder cladding material was superior to that of Co alloy powder cladding material both at the low speed (0.46m/s) and the high speed(0.92m/s). It seemed that the behavior of wear showed the abrasive wear at the early stage and the adhesive wear at the late stage.

• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.231-238
• /
• 2003

The fuel of light water reactor is used for several years under high temperature and pressure, so it needs to be clad with high corrosion resistance material. The cladding materials must have the characteristics of low absorption of a neutron and high corrosion resistance. Zircaloy-2 in Boiling Water Reactor, Zircaloy-4 in Pressurized Water Reactor have been used as cladding materials and Zirlo has been developed as the material for preventing the corrosion. If the fracture of the cladding tube occurs during operation, it will cause the economic loss to shut down and replace the system. So it is needed to evaluate the integrity of the cladding materials. In this paper, the tensile characteristics of the cladding materials were investigated for the basic research of fracture characteristics. Also the residual stress was analyzed to compare the tube type(original type) specimen and the flattened type specimen.