• 제목/요약/키워드: Circular Wall-Thinning

검색결과 11건 처리시간 0.023초

원주방향 노치형 감육부를 가진 배관의 손상거동 평가 (Evaluation of Failure Behavior of a Pipe Containing Circumferential Notch-Type Wall Thinning)

  • 김진원;박치용
    • 대한기계학회논문집A
    • /
    • 제27권8호
    • /
    • pp.1295-1302
    • /
    • 2003
  • In order to evaluate a failure behavior of pipe with notch-type wall thinning, the present study performed full-scale pipe tests using the 102mm, Schedule 80 pipe specimen simulated notch- and circular-type thinning defects. The pipe tests were conducted under the conditions of both monotonic and cyclic bending moment at a constant internal pressure of 10 MPa. From the results. of experiment the failure mode, load carrying capacity, deformation ability, and fatigue life of a notch-type wall thinned pipe were investigated, and they were compared with those of a circular-type wall thinned pipe. The failure mode of notched pipe was similar to that of circular-type thinned pipe under the monotonic bending load. Under the cyclic bending load, however, the mode was clearly distinguished with variation in the shape of wall thinning. The load carrying capacity of a pipe containing notch-type wall thinning was about the same or slightly lower than that of a pipe containing circular-type wall thinning when the thinning area was subjected to tensile stress, whereas it was higher than that of a pipe containing circular-type thinning defect when the thinning area was subjected to compressive stress. On the other hand, the deformation ability and fatigue life of a notch-type wall thinned pipe was lower than those of a circular-type wall thinned pipe.

원통형 딥드로잉 용기의 벽 두께 감소 최소화에 관한 실험적 연구 (Experimental Study on Minimizing Wall Thickness Thinning for Deep Drawing of Circular Shells)

  • 김두환
    • 소성∙가공
    • /
    • 제7권4호
    • /
    • pp.393-399
    • /
    • 1998
  • For minimizing wall thickness thinning of circular shells, a new stamping technology, the deep draw-ing process combined with ironing is approached and investigated. The design requirements for the deep drawing shells are to keep the optimum wall thickness with max. 10 percent thickness thinning of the initial blank thickness, to make uniform thickness strain distribution for the wall of circular shell and to improve the shape accuracy for the roundness and concentricity. In order to check the validity and effectiveness of proposed work, a sample process design is applied to a circular shell needed for a 4multi-stepped deep drawing. Through experiments, the variations of the thickness strain distribution in each drawing process are observed. Also a series of experiments are performed to investigate optimum process variables such as the geometry of tooling, radius and drawing rate. In particular, the advantage of current approach with ironing is shown in contrast to the conventional deep drawing process. From the results of proposed method, the optimum value of process variables are obtained, which contribute more uniform thickness strain distribution and better quality in the drawn product.

  • PDF

인장하중을 받는 직선 배관 감육부의 국부 탄소성 변형률 평가 방법 (Estimation Method of Local Elastic-Plastic Strain at Thinning Area of Straight Pipe Under Tension Loading)

  • 안중혁;김윤재;윤기봉;마영화
    • 대한기계학회논문집A
    • /
    • 제30권5호
    • /
    • pp.533-542
    • /
    • 2006
  • In order to assess the integrity of pipes with local thinning area, the plastic strain as well as the elastic strain at the root of thinned region are required particularly when fluctuating load is applied to the pipe. For estimating elastic-plastic strain at local wall thinning area in a straight pipe under tensile load, an estimation model with idealized fully circumferential constant depth wall thinning area is proposed. Based on the compatibility and equilibrium equations a nonlinear estimation equation, from which local elastic-plastic strain can be determined as a function of pipe/defect geometry, material and the applied strain was derived. Estimation results are compared with those from detailed elastic-plastic finite element analysis, which shows good agreements. Noting that practical wall thinning in nuclear piping has not only a circular shape but also a finite circumferential length, the proposed solution for the ideal geometry is extended based on two-dimensional and three-dimensional numerical analysis of pipes with circular wall thinning.

원형 감육이 발생한 중수로 피더관의 한계하중 평가 (Limit Loads for Circular Wall-Thinned Feeder Pipes Subjected to Bending and Internal Pressure.)

  • 제진호;이국희;정하주;김종성;김윤재
    • 대한기계학회논문집A
    • /
    • 제34권11호
    • /
    • pp.1675-1680
    • /
    • 2010
  • 캐나다형 중수로에서 피더관은 가동 중에 유동 가속 부식에 의해 감육이 발생한다. 피더관에 감육이 발생하면 배관 건전성이 떨어진다. 본 논문은 원형 감육이 발생한 피더관에서의 기기신뢰성 평가를 위한 한계 하중을 연구하였다. 유한요소 해석을 통하여 면내 굽힘 하중과 내압을 받는 경우에 대하여 연구하였다. 재료는 대변형 효과를 고려하고 탄성-완전소성 재료로 가정하였다. 원형 감육이 발생한 피더관에 대하여 내압과 닫힘 방향, 열림 방향 굽힘 하중에 대하여 한계하중해를 제시하였다.

굽힘각도를 고려한 원형 감육이 발생한 중수로 피더관의 한계하중 (Limit Loads for Circular Wall-Thinned Feeder Pipes Considering Bend Angle)

  • 배경동;제진호;김종성;김윤재
    • 대한기계학회논문집A
    • /
    • 제36권3호
    • /
    • pp.313-318
    • /
    • 2012
  • 캐나다형 중수로에서 피더관은 중수로 압력관에 중수를 공급하고 가열된 중수를 증기발생기로 보내는 배관으로 가동 중에 유동 가속 부식현상에 의해 감육이 발생한다. 배관에 감육이 발생하게 되면 배관의 건정성이 떨어진다는 결과는 앞선 연구에서 확인하였다. 본 논문에서는 45 도와 60 도의 굽힘각도를 갖는 피더관의 한계하중을 제시하고 제시된 연구결과를 바탕으로 임의의 굽힘각도를 갖는 피더관에서 감육이 발생했을 경우의 한계하중을 예측 할 수 있는 식을 제시하였다. 본 연구에서는 유한요소 해석을 통하여 굽힘 하중과 내압을 받는 경우에 대하여 연구를 진행하였고 특히 굽힘 하중의 경우 면내 열림 방향과 면내 닫힘 방향으로 나누어 진행하였다. 재료는 대변형 효과를 고려하고 탄성-완전소성 재료로 가정하였다.

장애물 주위의 비뉴턴 유체의 유동특성에 관한 수치적 연구 (NUMERICAL STUDY ON THE CHARACTERISTICS OF NON-NEWTONIAN FLUID FLOW OVER OBSTACLE)

  • 김형민
    • 한국전산유체공학회지
    • /
    • 제19권4호
    • /
    • pp.61-67
    • /
    • 2014
  • Since the most of the existing non-Newtonian models are not adequate to apply to the lattmce Boltzmann method, it is a challenging task from both the theoretical and the numerical points of view. In this research the hydro-kinetic model was modified and applied to the 3-D moving sphere in the circular channel flow and the characteristics of the shear thinning effect by the HK-model was evaluated and the condition of ${\Gamma}$ in the model was suggested for the stable simulation to generate non-trivial prediction in three dimension strong shear flows. On the wall boundaries of circular channel the curved wall surface treatment with constant velocity condition was applied and the bounceback condition was applied on the sphere wall to simulate the relative motion of the sphere. The condition is adequate at the less blockage than 0.7 but It may need to apply a multi-scale concept of grid refinement at the narrow flow region. to obtain the stable numerical results.

연질파이프의 두께보증형 벤딩공정에 대한 성형해석에 대한 연구 (A study on forming analysis for the soft pipe bending process of thickness guarantee)

  • 정동원;정지현;조종래
    • Journal of Advanced Marine Engineering and Technology
    • /
    • 제37권1호
    • /
    • pp.66-71
    • /
    • 2013
  • 산업현장에서 널리 사용되고 있는 연질용 벤딩파이프는 벤딩 후 외관의 주름이나 스프링 백, 관이 얇아지는 현상 등이 자주 발생하여 크랙이나 파이프 파공 등의 문제가 대두되고 있지만 이를 완벽히 해결할 수 있는 벤딩기계는 아직 전무한 실정이다. 따라서 본 연구에서는 고품질 정밀형 연질재료 전용 벤딩기계의 개발을 위한 기초연구로서 벤딩툴인 맨드릴을 자체 설계제작하고 그 성능을 검증한다. 또한 벤딩 시 관이 얇아지는 현상에 대해 두께 감소율과 손상정도 등을 시뮬레이션으로 분석하고 그 해결방법을 제시하고자 한다.

인장드로잉법에 의한 원통성형에 관한 실험적 연구 (A Experimental Study of Cup forming by Stretch-Drawing Process)

  • 김영수
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2000년도 춘계학술대회논문집
    • /
    • pp.123-128
    • /
    • 2000
  • Fundamental and informative data of axi-symmetric stretch-drawing of several sheetmetals with thicknesses of 0.7-1.0mm are presented both for single and double operations. Very small radius is applied to the die profile (or-shoulder) ion all operations. to induce wall-thinning by the effect of bending-under-tension from which the name 'stretch-drawing' comes. It is clearly demonstrated that deeper cups could be formed by single and double stretch-drawings from smaller circular blanks due to such wall-thinning action than in the usual deep-drawing of larger blanks, From this fact it is emphasized that the deep-drawability of a sheet metal is not evaluated simply by the conventional L.D.R (limiting drawing ratio) but the depth of the drawn cup should also be taken into account./ Many experimental data about various metals and thicknesses given in this paper offer a valuable information in this process for more general use which recommends to replace the conventional deep-drawing process by the stretch-drawing process both for single and double operations. In the single stretch-drawing it is also confirmed that a deeper cup can be produced by raising the blank-holding force at later stage of operation.

  • PDF

Direct simulations on 2D mold-filling processes of particle-filled fluids

  • Hwang, Wook-Ryol;Kim, Worl-Yong;Kang, Shin-Hyun;Kim, See-Jo
    • Korea-Australia Rheology Journal
    • /
    • 제21권3호
    • /
    • pp.193-200
    • /
    • 2009
  • We present a direct simulation technique for two-dimensional mold-filling simulations of fluids filled with a large number of circular disk-like rigid particles. It is a direct simulation in that the hydrodynamic interaction between particles and fluid is fully considered. We employ a pseudo-concentration method for the evolution of the flow front and the DLM (distributed Lagrangian multipliers)-like fictitious domain method for the implicit treatment of the hydrodynamic interaction. Both methods allow the use of a fixed regular discretization during the entire computation. The discontinuous Galerkin method has been used to solve the concentration evolution equation and the rigid-ring description has been introduced for freely suspended particles. A buffer zone, the gate region of a finite area subject to the uniform velocity profile, has been introduced to put discrete particles into the computational domain avoiding any artificial discontinuity. From example problems of 450 particles, we investigated the particle motion and effects of particles on the flow for both Newtonian and shear-thinning fluid media. We report the prolonged particle movement toward the wall in case of a shear-thinning fluid, which has been interpreted with the shear rate distribution.

원통의 2단 인장드로잉 성형에 관한 연구 (A Study of Cup forming by double Stretch-Drawing Process)

  • 김영수;정태훈;일본명
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2003년도 추계학술대회
    • /
    • pp.406-411
    • /
    • 2003
  • It is clearly demonstrated that deeper cups could be formed by single and double stretch-drawings from smaller circular blanks due to such wall-thinning action than in the usual deep-drawing of larger blanks. From this fact, it is emphasized that the deep-drawability of a sheet metal Is not evaluated simply by the conventional L.D.R (limiting drawing ratio), but the depth of the drawn cup should also be taken into account. Many experimental data about various metals and thicknesses given in this paper offer a valuable information in this process for more general use which recommends to replace the conventional deep-drawing process by the stretch-drawing process both for single and double operations. In the single stretch-drawing, it is also confirmed that a deeper cup can be produced by raising the blank-holding force at later stage of operation.

  • PDF