• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.2
• /
• pp.149-154
• /
• 2000

The purpose of this study is to measure the compression temperature in cylinder by using the fine thermocouple. As for using the thermocouple, it's response time delay should be regarded, even if it is a fine one. So, the output of thermocouple needs some compensation. The compensation circuit, which consists of a differential and an adding circuit is used for the compensate the time lag. And the time constant of the compensation circuit is determined the time between the TDC and the maximum point of the thermocouple output. Using this compensation circuit, the compression temperature is investigated of the cylinder in the diesel engine.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.406-409
• /
• 2008

This paper presents the integrated magnetic circuit designing method for phase shift full bridge(PSFB) converter. The integrated magnetic circuit is implemented on redesigned of EI core. The transformer windings are located on center leg and the two inductors are located on the outer legs with air gap. Based on the equivalent circuit model, the principle of operation of the PSFB converter is explained. The operation and performance of the proposed circuit are verified on a 1.2 kW prototype converter. The analysis and design of the integrated magnetic circuit is verified through the experimental and simulation results.

• Journal of Information Display
• /
• v.9 no.4
• /
• pp.45-49
• /
• 2008

The characteristics of the sustain-driving circuit were examined in this paper. The sustain-driving circuit is in charge of the most important part of PDP driving because it manages most of the power consumption in the PDP. A couple of gatedriving circuits for the sustain-driving circuit were introduced in this paper, and a new driving circuit was also proposed. This new circuit is more cost-effective and has a simpler PCB layout compared to the conventional one. Some additional driving advantages were noted as well.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.669-671
• /
• 2001

This paper describes the operating characteristic analysis of PM-type magnetic circuit breaker for electromagnetic field, electric circuit and mechanical motion problems. Transient calculations are based upon the magnetic equivalent circuit analysis including non-linearity of materials and using iteration routines. The analysis results of this magnetic equivalent circuit are compared with those of FEM.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.134-136
• /
• 2000

This paper deals with the analysis on the TRV generating circuit and the TRV waveform occurred from the short-circuit tests using only the short-circuit generator. And the results of analysis on the proposed TRV generating circuit and TRV measured are described.

• Proceedings of the KIEE Conference
• /
• 2005.07a
• /
• pp.569-571
• /
• 2005

In case of dead-tank circuit breaker with the earthed enclosure, the dielectric performance for phase to ground should be verified under the hot-gas condition produced by the current interruption. This test condition is required in breaking test duties with the rated short-circuit current and rated voltage. And, KERI has completed the reinforcement of the synthetic testing facilities and these facilities have the testing capacity which enables the full-pole testing for 800kV circuit breaker by adopting the series voltage injection method. So, this paper introduced the test circuit and procedures about the full-pole and the multi-part testing method which was devised to estimate the full -insulation of phase-to-ground for the multi-pole and dead-tank circuit breaker.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.148-151
• /
• 2005

This paper proposes a high speed interface using redundant multi-valued logic for high speed communication ICs. This circuit is composed of encoding circuit that serial binary data are received and converted into parallel redundant multi-valued data, and decoding circuit that convert redundant multi-valued data to parallel binary data. Because of the multi-valued data conversion, this circuit makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was designed using a 0.35${\mu}m$ standard CMOS Process. Proposed demultiplexer is achieved an operating speed of 3Gb/s with a supply voltage of 3.3V and with power consumption of 48mW. Designed circuit is limited by maximum operating frequency of process. Therefore, this circuit is to achieve CMOS communication ICs with an operating speed greater than 3Gb/s in submicron process of high of operating frequency.

• Journal of Information Display
• /
• v.7 no.4
• /
• pp.24-26
• /
• 2006

We have developed a new driving method named TROPHY(Talented Role-playing Technology with Dual Polarity sustainer in Hybrid Mono board). In this method, the sustain voltage is partially compared to the conventional method and the number of power sources is reduced by voltage level unification during the reset, address and sustain period. The hybrid mono board was especially developed to implement those technologies. Through this, we can lower the cost with the TROPHY compared to the conventional one. It is a suitable technology to improve the reliability of circuit and image sticking problem. We can also reduce the number of driving boards and the EMI problem compared with those of the conventional method.

• Journal of information and communication convergence engineering
• /
• v.7 no.2
• /
• pp.215-218
• /
• 2009

In this paper, temperature stable current and voltage references using simple CMOS bias circuit are proposed. To obtain temperature stable characteristics of bias circuit a bandgap reference concept is used in a conventional circuit. The parasitic bipolar transistors or MOS transistors having different threshold voltage are required in a bandgap reference. Thereby the chip area increase or the extra CMOS process is required compared to a standard CMOS process. The proposed reference circuit can be integrated on a single chip by a standard CMOS process without the extra CMOS process. From the simulation results, the reference current variation is less than ${\pm}$0.44% over a temperature range from - $20^{\circ}C$ to $80^{\circ}C$. And the voltage variation is from - 0.02% to 0.1%.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.246-249
• /
• 2006

We have developed a new driving method named TROPHY(Talented Role-playing Technology with Dual Polarity sustainer in Hybrid Mono board). In this method, the sustain voltage is halved compared to the conventional method and the number of power sources is reduced by voltage level unification during the reset, address and sustain period. The hybrid mono board was especially developed to implement those technologies. Therefore, we can lower the cost with the TROPHY compared to the conventional one. It is suitable technology to improve the reliability of circuit and image sticking problem. We can also reduce the number of driving boards and the EMI problem comparing to those of the conventional method.