• Journal of Korean Society of Forest Science
• /
• v.99 no.4
• /
• pp.625-632
• /
• 2010

This study was carried out to analyze the yarding productivity and cost of the man-power operation by plastic chute, the yarding operation by yarder attached in tractor (Chuncheon Tower-yarder) and yarding operation by Tower-yarder (RME-300T) in forest tending operation. As result of average yarding timber volume was 0.67 $m^3$, 3.8 $m^3$ and 7.3 $m^3$ per day and man, respectively. And, when an yarding timber volume was 60 $m^3$/ha, the total yarding time including setting up and dismantling time of the plastic chute and yarding line was 20 days and 2 hours, 7 days and 1 hours and 21 minutes, 3 days and 4 hours and 27 minutes, respectively. The operation costs were 104,448 won/$m^3$, 29,968 won/$m^3$ and 23,032 won/$m^3$, respectively. And, when yarding timber volume was 60 $m^3$/ha, the total operation cost including setting up and dismantling time of the plastic chute and yarding line was 7,429,173 won/ha, 2,431,573 won/ha and 1,610,672 won/ha, respectively.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2008.11a
• /
• pp.173-177
• /
• 2008

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.583-584
• /
• 2005

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.162-166
• /
• 1992

This paper presents a new control methology for improving conventional drum and chute components, which have been operated by workers with levers. In a system for clute operations using a hydraulic power unit as an actuator and also develsed a proportional-integral controller for drum operations using electrical power units.

• Tunnel and Underground Space
• /
• v.14 no.5
• /
• pp.305-317
• /
• 2004

Due to the steep and narrow characteristic of domestic coal beds, the slant chute caving or sub-level caving method have been mainly adopted in Korea, whereas the long-wall mining has been widely used all around world. However, the slant chute caving or sub-level caving method have disadvantage of not giving much information on the scale and characteristic of abandoned mines. Hence, those information on the abandoned mines in Korea are not easily available. In this study, based on the characteristic investigation of the domestic mining methods, the geological survey and safety analysis were carried out for Donghae highway section 2. Finally, the optimum ground reinforcement methods for that site were selected.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.219-219
• /
• 2004

지금까지 식품, 약품 및 음료 산업 등에서 내용물을 충전 후 밀봉하기 위한 방법이 다양하게 개발되어 사용되고 있으며, 특히 뚜껑을 체결하는 인라인 캐핑머신(In-line capping machine)은 포장 공정에 필수적인 장치이다. 이와 같은 장치의 설계 시 고려되어야 할 사항으로서 작업 공정이 연속적인데 있다. 또한, 어느 한 제품을 용기에 채운 후 완전한 상품으로 조립하기까지, 캐핑머신의 신뢰성은 공정의 연속성과 생산성을 좌우하기 때문에 매우 중요한 요소이다.(중략)

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.3
• /
• pp.13-18
• /
• 2009

This paper describes flow characteristics in a piping system having various duct shapes on refuse collecting system. A simulator for the refuse collecting system is designed to analyze the flow characteristics in the piping system. The simulator consists of an air intake, a waste chute, circular duct having various shapes, cyclone and turbo blower. The simulator has four different duct shapes: straight, curved, inclined and Y-shaped ducts. Three-dimensional Navier-Stokes analysis is introduced to analyze the pressure loss in the piping system. Throughout the numerical simulation, pressure loss obtained by numerical simulation has a good agreement with the results of experimental measurements. The selected length of curved and Y-ducts for the pressure loss is determined using pressure distributions on the duct. Flow and pressure characteristics in the piping system of the simulator are evaluated by numerical simulation and discussed in detail.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.588-589
• /
• 2005

Current expertise in air-water turbulent flows on stepped chutes is limited to laboratory experiments at low to moderate Reynolds numbers on flat horizontal steps. In this study, highly turbulent air-water flows skimming down a large-size stepped chute were systematically investigated with a $22^{\circ}$ slope (Fig. 1). Turbulence manipulation was conducted using vanes or longitudinal ribs to enhance interactions between skimming flows and cavity recirculating regions (Fig. 2). Systematic experiments were performed with seven configurations. The results demonstrated the strong influence of vanes on the air-water flow. An increase in flow resistance was observed consistently with maximum flow resistance achieved with vanes placed in a zigzag pattern.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.590-591
• /
• 2005

Hydrodynamic pressure fluctuations and their roles on the design of hydraulic structures has been the subject of many investigations. The studies showed that turbulent pressure fluctuations may cause serious damages to hydraulic structures. In case of high velocity flows, separation of flow from the boundary also causes the local pressure to drop and as a result, the resultant pressure fluctuations may trigger cavitation. Sever hydrodynamic pressures are also associated with the vibration of structures. Therefore, in this work, experiments were performed to determine the intensity of pressure fluctuations and their distribution along the bed of a ski-jump flip bucket. Experiments were completed on a physical model at the Institution of Water Research of Iran. The results consist of the statistical characteristics of pressure fluctuations, its maximum, minimum, and r.m.s values along the bed of the bucket. The spectral analysis of pressure fluctuations which is useful for the instability analysis of such structures is also provided. It is hoped that the present results will help the designer of such structures.

• Water Engineering Research
• /
• v.4 no.3
• /
• pp.127-139
• /
• 2003

This paper presents the hydraulic analysis of the oxygen transfer through the air entrainment and the relationships between the efficiency of the oxygen transfer and the hydraulic parameters in the riparian riffles. Field survey on the pool-riffle formation of the river reach and the measurements of the oxygen transfer in the riffles were performed. Air entrainment occurred more frequently in the edged gravels rather than in the round and edgeless ones, and it was formed mainly from behind the trailing edges of the gravels. Oxygen transfer was found to be proportional to the flow velocity, the flow discharge, and the Froude number, but to be not closely related to the particle diameter. Average value of oxygen transfer in the riffles of study area was about 0.085, which shows good efficiency compared with results of smooth chute. Variation of the water level, which increases in proportion to the flow velocity and the flow discharge, seems to make the air entrainment more active, but has not been verified quantitatively. Relationships between the air entrainment and the variation of the water level must be considered in the further study.