• Korean Chemical Engineering Research
• /
• 제51권6호
• /
• pp.760-765
• /
• 2013

액적기반 미세유체 시스템을 이용해 난백단백질인 라이소자임의 결정화실험을 하였다. Flow-focusing 칩을 이용해 water-in-oil 형태의 액적을 만들고 페트리 디쉬와 십자몰드에 넣은 후, 액적 내부에서 라이소자임 수용액과 침전제 (NaCl) 사이의 액-액 반응을 관찰하였다. 그리고 수용액의 pH가 4.8일 때와 7.2일 때의 결정형태를 비교하였다. 그 결과, pH 4.8에서는 다면체 또는 판상형의 결정이 형성되었고, pH 7.2에서는 침상형 결정이 생성되었다. pH 4.8, 7.2 두 경우 액적이 홀로 있을 때에는 액적부피가 유지되거나 감소하면서 결정이 형성되었다. 하지만 액적이 서로 인접해 있을 때는 액적사이의 상호작용이 관찰되었고, 두 pH에서 다른 경향성을 보였다. pH 4.8에서는 인접한 액적의 부피에 영향을 주어 한 액적의 부피가 커졌고, 부피가 커진 액적에서 결정이 형성되었다. pH 7.2에서는 부피에 영향을 서로 주지 않고 각각의 액적에서 결정이 형성되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1060-1062
• /
• 1999

Pulsed Nd:YAG laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. And the parallel mesh is added to increase laser output power. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition, we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the parallel mesh and the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 10pps to 110pps by the step of 20pps at 1000V and 1200V, it is found that the laser efficiency decreases but the laser output power increases about 5W at each step.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• 한국전자파학회논문지
• /
• 제11권6호
• /
• pp.946-951
• /
• 2000

본 논문은 접지면에 형성된 디펙트를 갖는 전송선로 구조인 DGS의 특성 및 등가회로를 구하고 디펙트의 크기에 따른 등가 집중소자 값을 추출하였으며, DGS에 집중소자를 달아주어 그 영향을 살펴보았다. 제시된 DGS는 아령 모양의 디펙트로 아였으며, 병렬 단락 공진기에 적용하였다. 침 형태의 집중소자인 저항, 인덕터, 커패시터를 각각 달아주어 주파수 특성을 살펴보았다. 또한 실험결과 Q factor와 공진 주파수가 DGS에 달아준 외부소자에 의해 제어됨을 보였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2204-2206
• /
• 1999

Pulsed Nd:YAC laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition. we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 30pps to 120pps by the step of 30pps at 1200V, it is found that the laser efficiency decreases but the laser output power increases about 6W at each step.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1289-1297
• /
• 2005

The flow in a microchannel is usually characterized as a low Reynolds number (Re) so that good mixing is quite difficult to be achieved. In this regard, we developed a novel chaotic micromixer, named Serpentine Laminating Micromixer (SLM) in the present study, Part 1. In the SLM, the higher level of chaotic mixing can be achieved by combining two general chaotic mixing mechanisms: splitting/recombination and chaotic advection. The splitting and recombination (in other term, lamination) mechanism is obtained by the successive arrangement of 'F'-shape mixing units in two layers. The chaotic advection is induced by the overall three-dimensional serpentine path of the microchannel. Chaotic mixing performance of the SLM was fully characterized numerically. To compare the mixing performance, a T-type micromixer which has the same width, height and length of the SLM was also designed. The three-dimensional numerical mixing simulations show the superiority of the SLM over the T-type micromixer. From the cross-sectional simulation results of mixing patterns, the chaotic advection effect from the serpentine channel path design acts favorably to realize the ideal lamination of fluid flow as Re increases. Chaotic mixing mechanism, proposed in this study, could be easily integrated in Micro-Total-Analysis-System, Lab-on-a-Chip and so on.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1298-1306
• /
• 2005

In this paper, Part II, we realized the Serpentine Laminating Micromirer (SLM) which was proposed in the accompanying paper, Part I, by means of the injection molding process in mass production. In the SLM, the higher level of chaotic mixing can be achieved by combining two general chaotic mixing mechanisms of splitting/recombination and chaotic advection by the successive arrangement of 'F'-shape mixing units in two layers. Mold inserts for the injection molding process of the SLM were fabricated by SU-8 photolithography and nickel electroplating. The SLM was realized by injection molding of COC (cyclic olefin copolymer) with the fabricated mold inserts and thermal bonding of two injection molded COC substrates. To compare the mixing performance, a T-type micromixer was also fabricated. Mixing performances of micromixers were experimentally characterized in terms of an average mixing color intensity of a pH indicator, phenolphthalein. Experimental results show that the SLM has much better mixing performance than the I-type micromixer and chaotic mixing was successfully achieved from the SLM over the wide range of Reynolds number (Re). The chaotic micromixer, SLM proposed in this study, could be easily integrated in Micro-Total-Analysis- System , Lab-on-a-Chip and so on.

• 한국자기학회지
• /
• 제18권1호
• /
• pp.28-31
• /
• 2008

일축 이방성을 가진 퍼멀로이 박막을 제작하여 이방성 자기저항(anisotropic magnetoresistance)에 대하여 연구하였다. 시편의 길이 방향에 대하여 자화 용이축의 각을 $18^{\circ}$씩 기울어지게 변화를 준 5종류의 시편에 대하여 자기저항의 변화를 조사하였다. 박막면에 평행한 인가 자기장에 대하여 시편의 길이 방향과 자화 용이축 사이의 각이 증가함에 따라 세로자기저항(longitudinal magnetoresistance)의 변화 폭은 증가하는 반면, 가로자기저항(transverse magnetoresistance)의 변화 폭은 감소를 나타내었다. 이러한 자화 용이축 변화에 따른 자기저항의 변화를 이방성 자기저항과 일축 이방성을 가진 단일자구 모델로 설명하였다. Magneto-optic Kerr effect를 이용하여 측정한 자구 사진으로부터 자화 스위칭이 일어나는 구간에서 반대 방향의 지구가 생성되고 전파되는 과정을 관측하였으며 이에 대응하는 자기저항의 변화를 관측하였다.

• 한국재료학회지
• /
• 제24권7호
• /
• pp.351-356
• /
• 2014

A spherical $Sr_4Al_{14}O_{25}:Eu^{2+}$ phosphor for use in white-light-emitting diodes was synthesized using a liquid-state reaction with two precipitation stages. For the formation of phosphor from a precursor, the calcination temperature was $1,100^{\circ}C$. The particle morphology of the phosphor was changed by controlling the processing conditions. The synthesized phosphor particles were spherical with a narrow size-distribution and had mono-dispersity. Upon excitation at 395 nm, the phosphor exhibited an emission band centered at 497 nm, corresponding to the $4f^65d{\rightarrow}4f^7$ electronic transitions of $Eu^{2+}$. The critical quenching-concentration of $Eu^{2+}$ in the synthesized $Sr_4Al_{14}O_{25}:Eu^{2+}$ phosphor was 5 mol%. A phosphor-converted LED was fabricated by the combination of the optimized spherical phosphor and a near-UV 390 nm LED chip. When this pc-LED was operated under various forward-bias currents at room temperature, the pc-LED exhibited a bright blue-green emission band, and high color-stability against changes in input power. Accordingly, the prepared spherical phosphor appears to be an excellent candidate for white LED applications.

• 한국정밀공학회지
• /
• 제29권2호
• /
• pp.214-221
• /
• 2012

Recently, the biochip which is a prime representation of NT, IT, BT, as an example of convergence technology, has been frequently mentioned. With the recent rapid advance in biotechnology, these compact devices, such as lab-on-a-chip or u-TAS, have been developed, and more research is needed. These compact devices typically use the micro-channel in order to shed or detach and mix a variety of materials. Specially, in micro-fluidic systems, a mixer is necessary to produce a mixture because only laminar flow occurs at a low-Reynolds number. To solve this problem, HVM a micromixer that induces a horizontal and vertical multi-mixing flow motion, is proposed. The mixing performance was analyzed and verified by optimizing the shape through the CFD analysis and evaluating the structural analysis and the soundness with material properties that are obtained through the basic experiment.