• Structural Engineering and Mechanics
• /
• v.87 no.4
• /
• pp.375-389
• /
• 2023

In many fiber concrete beams with Carbon Fiber Reinforced Polymer (CFRP), debonding occurs between the carbon sheets and the concrete due to the low strength of the bonding resin. A total of 42 fiber concrete beams with a cross-section of 10×10 cm with a span length of 50 cm are fabricated and retrofitted with CFRP and subjected to a 4-point bending test. Graphene Oxide (GO) at 1, 2, and 3 wt% of the resin is used to improve the mechanical properties of the bonding resins, and the effect of length, width, and the number of layers of CFRP and resin material are investigated. The crack pattern, failure mode, and stress-strain curve are analyzed and compared in each case. The results showed that adding GO to polyamine resin could improve the bonding between the resin and the fiber concrete beam. Furthermore, the optimum amount of nanomaterials is equal to 2% by the weight of the resin. Using 2% nanomaterials showed that by increasing the length, width, and number of layers, the bearing and stiffness of fiber concrete beams increased significantly.

• Food Science and Preservation
• /
• v.30 no.3
• /
• pp.419-433
• /
• 2023

Dried apple bugak, a traditional Korean dried food, was made using superfine powders of glutinous rice (GR), non-glutinous rice (NGR), and Wasabia koreana Nakai leaf (WKNL) as coating materials. This study aimed to determine the effect of coating sliced apples with superfine GR powders substitute with superfine NGR and WKNL powders at different ratios. Apple slices coated with superfine GR, NGR and WKNL powders were air-fried and compared with dried and air-fried apple bugak coated with superfine GR powders. The results showed that coating apple slices with superfine GR powders with the addition of superfine NGR and WKNL powders significantly increased oil absorption capacity and antioxidant activity but reduced viscosity, water absorption capacity, total polyphenol, total flavonoids contents, and improved color and structural improvements. Among all the samples, 80:20:5-treated (GR:NGR:WKNL) dried and air-fried bugak showed enhanced quality characteristics. Thus, the results suggested that coating apple slices by the substituting GR superfine rice powders with 10 or 20% of NGR and 3 or 5% of WKNL superfine powders produces good quality dried and air-fried bugak with nutritious characteristics.

• Journal of Korean Society for Quality Management
• /
• v.51 no.4
• /
• pp.735-749
• /
• 2023

Purpose: The purpose of this study is to derive solutions and prevent similar cases from occurring by analyzing the causes of cracks found in temperature cycling tests of rocket motor. Methods: By combining the results of the current state confirmation test, non-destructive test, domestic and foreign rocket motor comparison test, cutting test, and adhesion test according to the number of times to apply mold release agent, a Cause and Effect Diagram analysis was performed to derive the cause of cracks. Results: Through this study, 26 factors that could cause cracking in rocket motors during temperature cycling tests were identified. Through various additional test results, a total of five causes were identified, including chemical and structural design of the joint between the propellant and stress relief insert, omission of procedure in the manufacturing procedures, natural aging due to temperature, and load accumulation due to temperature changes. The fundamental cause was confirmed to be insufficient consideration of the release properties of the propellant and stress relief insert. Conclusion: During the design process, it was confirmed that this could be solved by structurally or chemically designing the insert so that it does not combine with the propellant, or by applying a mold release agent during the manufacturing process.

• Applied Chemistry for Engineering
• /
• v.23 no.4
• /
• pp.377-382
• /
• 2012

CdS thin films have been widely used as a buffer layer of CIGS semiconductor solar cells to reduce the lattice mismatch between transparent electrode and absorber layer. In order to prepare the CdS films with high transparency and low resistivity, they were deposited by varying Cd concentration with the constant S concentration in the solution using chemical bath deposition method. They were analyzed in terms of structural, optical and electrical properties of CdS films according to the $[S^{2-}]/[Cd^{2+}]$ ratio. In the case of Cd concentration higher than S concectration, CdS thin films were formed mainly by cluster- by-cluster formation due to the homogeneous reaction between Cd and S in the solution. Therefore the grain size increased and the transmittance decreased. On the other hand, in the case of Cd concentration lower than S concentration, CdS films were formed by heterogeneous reaction on the substrate rather than in the solution. The CdS films have the grains with the uniform circular shape of a few hundreds ${\AA}$. As the Cd concentration increased in the solution, the $[S^{2-}]/[Cd^{2+}]$ ratio decreased and the resistivity decreased by the increase in the carrier concentration due to the formation S vacancy by the excess Cd.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.9-14
• /
• 2022

Silica aerogel is a porous material with a very low density and high specific surface area. Still, its application is limited due to its weak mechanical properties due to structural features. To solve this problem, a method of complexing it with various polymers has been proposed. We synthesized polyimide cross-linked silica aerogel by the sol-gel process to obtain high mechanical properties. Tetraethyl orthosilicate (TEOS) was used as a precursor to make silica aerogel, and 3- aminopropyltriethoxysilane (APTES) was used as a coupling agent for cross-linking polyimide. Polyimide was synthesized using pyromellitic dianhydride and 3,5-diaminobenzoic acid, and mechanical properties were improved by crosslinking polyimide with 10 repeating units in the polyimide chain using the reaction formula ${\frac{n_1}{n_2}}={\frac{n}{n+1}}$ To realize silica aerogel, polyimide having various weight ratios was added before gelation, resulting in a 19-fold or greater increase in maximum compressive strength compared to pure silica aerogel. From this study, an enhancement of silica aerogel could be enhanced through polymer cross-linking bonds.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.3
• /
• pp.101-104
• /
• 2008

GaN films were grown on the vertical and horizontal reactors by the hydride vapour phase epitaxy (HVPE). The structural and optical characteristics of the GaN films were investigated depending on the reactor-type. GaN epilayers were characterized by double crystal X-ray diffraction (DC-XRD), transmission electron microscopy (TEM) and photoluminescence (PL). Surface defects of two kinds of the GaN films were revealed by the wet chemical etching method, using $H_3PO_4$ acid at $200^{\circ}C$ for 8 minutes. Hexagonal etch pits were analyzed by optical microscopy and SEM. Etch pit densities were calculated to be approximately $1.4{\times}10^7$ and $1.2{\times}10^6\;cm^{-2}$ for GaN layers grown on horizontal and vertical reactors, respectively. Those results show GaN grown in the vertical reactor having a better quality of optical properties and crystallinity than that in the horizontal reactor.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.7
• /
• pp.1038-1042
• /
• 2006

A new type of DTPA-bis-amides (L1-L4) and their Gd(III)-complexes of the type $[Gd(L)(H_2O)]{\cdot}nH_2O$ (5: L1; 6: L2; 7: L3; 8: L4) have been prepared and characterized by analytical and spectroscopic techniques. The X-ray crystal structure of 8 has been determined for structural confirmation. The coordination geometry adopts a tricapped trigonal prism geometry with L4 acting as a chelate octadentate and a water molecule in the coordination sphere. Crystals are monoclinic, $P2_1$, a = 14.468(3), b = 19.235(4), c = 13.527(2) $\AA$ $\beta$ = $107.245(3)^{\circ}$, V = 3595.2(11) $\AA^3$, Z = 4, $D_{calc}$ = 1.570. Significant increases in relaxivities are observed with 6 and 7 as compared with that of $Omniscan^{(R)}$, a commercial MR agent: R1 = 12.46 $mM^{-1}\;s^{-1}$, R2 = 8.76 $mM^{-1}\;s^{-1}$ for 6; R1 = 12.77 nm-1 s-1, R2 = 7.60 mM-1 s-1 for 7; R1 = 4.9 $mM^{-1}\;s^{-1}$, R2 = 4.8 $mm^{-1}\;s^{-1}$ for $Omniscan^{(R)}$. In the case of 5, however, both R1 and R2 are found to be lower to show 2.09 $mM^{-1}\;s^{-1}$, and 1.82 $mM^{-1}\;s^{-1}$, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.11
• /
• pp.1653-1668
• /
• 2005

Assembly of hybrid mesophases through the combination of amphiphilic block copolymers, acting as structuredirecting agents, and silicon sources using low acid catalyst concentration regimes is a versatile strategy to produce large quantities of high-quality ordered large-pore mesoporous silicas in a very reproducible manner. Controlling structural and textural properties is proven to be straightforward at low HCl concentrations with the adjustment of synthesis gel composition and the option of adding co-structure-directing molecules. In this account, we illustrate how various types of large-pore mesoporous silica can easily be prepared in high phase purity with tailored pore dimensions and tailored level of framework interconnectivity. Silica mesophases with two-dimensional hexagonal (p6mm) and three-dimensional cubi (Fm$\overline{3}$m, Im$\overline{3}$m and Ia$\overline{3}$d) symmetries are generated in aqueous solution by employing HCl concentrations in the range of 0.1−0.5 M and polyalkylene oxide-based triblock copolymers such as Pluronic P123 $(EO_{20}-PO_{70}-EO_{20})$ and Pluronic F127 $(EO_{106}-PO_{70}-EO_{106})$. Characterizations by powder X-ray diffraction, nitrogen physisorption, and transmission electron microscopy show that the mesoporous materials all possess high specific surface areas, high pore volumes and readily tunable pore diameters in narrow distribution of sizes ranging from 4 to 12 nm. Furthermore, we discuss our recent advances achieved in order to extend widely the phase domains in which single mesostructures are formed. Emphasis is put on the first synthetic product phase diagrams obtained in $SiO_2$-triblock copolymer-BuOH-$H_2O$ systems, with tuning amounts of butanol and silica source correspondingly. It is expected that the extended phase domains will allow designed synthesis of mesoporous silicas with targeted characteristics, offering vast prospects for future applications.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3285-3292
• /
• 2012

The interaction of thiazole drug with (6,0) zigzag single-walled boron nitride nanotube of finite length in gas and solvent phases was studied by means of density functional theory (DFT) calculations. In both phases, the binding energy is negative and presenting characterizes an exothermic process. Also, the binding energy in solvent phase is more than that the gas phase. Binding energy corresponding to adsorption of thiazole on the BNNT model in the gas and solvent phases was calculated to be -0.34 and -0.56 eV, and about 0.04 and 0.06 electrons is transferred from the thiazole to the nanotube in the phases. The significantly changes in binding energies and energy gap values by the thiazole adsorption, shows the high sensitivity of the electronic properties of BNNT towards the adsorption of the thiazole molecule. Frontier molecular orbital theory (FMO) and structural analyses show that the low energy level of LUMO, electron density, and length of the surrounding bonds of adsorbing atoms help to the thiazole adsorption on the nanotube. Decrease in global hardness, energy gap and ionization potential is due to the adsorption of the thiazole, and consequently, in the both phases, stability of the thiazole-attached (6,0) BNNT model is decreased and its reactivity increased. Presence of polar solvent increases the electron donor of the thiazole and the electrophilicity of the complex. This study may provide new insight to the development of functionalized boron nitride nanotubes as drug delivery systems for virtual applications.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3407-3412
• /
• 2012

The Ti incorporation at Fe-site in the double perovskite lattice of $Sr_2FeNbO_6$ (SFNO) system is studied. The Ti concentration optimization yielded an efficient photocatalyst. At an optimum composition of Ti as x = 0.07 in $Sr_2Fe_{1-x}Ti_xNbO_6$, the photocatalyst exhibited 2 times the quantum yield for photolysis of $H_2O$ in presence of $CH_3OH$, than its undoped counterpart under visible light (${\lambda}{\geq}420nm$). Heavily Ti-doped $Sr_2Fe_{1-x}Ti_xNbO_6$ lattice exhibited poor photochemical properties due to the existence of constituent impurity phases as observed in the structural characterization, as well as deteriorated optical absorption. The higher electron-density acquired by n-type doping seem to be responsible for the more efficient charge separation in $Sr_2Fe_{1-x}Ti_xNbO_6$ (0.05 < x < 0.4) and thus consequently displays higher photocatalytic activity. The Ti incorporated structure also found to yield stable photocatalyst.