• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1047-1048
• /
• 2011

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1438-1445
• /
• 2015

A new DC-DC power converter is researched for renewable energy and battery hybrid power supplies systems in this paper. At the charging mode, a renewable energy source provides energy to charge a battery via the proposed converter. The operating principle of the proposed converter is the same as the conventional DC-DC buck converter. At the discharging mode, the battery releases its energy to the DC bus via the proposed converter. The proposed converter is a non-isolated high step-up DC-DC converter. The coupled-inductor technique is used to achieve a high step-up voltage gain by adjusting the turns ratio. Moreover, the leakage-inductor energies of the primary and secondary windings can be recycled. Thus, the conversion efficiency can be improved. Therefore, only one power converter is utilized at the charging or discharging modes. Finally, a prototype circuit is implemented to verify the performance of the proposed converter.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.4
• /
• pp.307-311
• /
• 2016

Several types of supercapacitors have been developed for energy storage systems. Among them, the hybrid type has advantages such as a large capacitance per weight compared with the electric double-layer capacitator type. In this study, constant current charging and discharging tests were conducted for recently developed hybrid-type supercapacitors. Based on the experimental results, the capacitance and equivalent series resistance were obtained. The capacitance was larger than the designed capacitance at a low current but became small at a high current. In addition, the capacitance depended on the cell voltage. These results can be used to design an energy storage system.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.194-195
• /
• 2010

This paper describers a bidirectional DC/DC converter for charging and discharging of a supercapacitor. Simulations are carried out to see the operation and performance of the 3kW-rated converter. Simulation results show that the charging/discharging characteristics is sufficient for the compensation of the response delay of a fuel cell.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.171-176
• /
• 2023

In the modern society of the 21st century, portable electronic products using secondary batteries are continuously becoming lightweight and miniaturized. And along with this trend, we are active in the era of the Fourth Industrial Revolution, where we collect and share information in our daily lives using wearable electronic devices. Therefore, the role of secondary batteries that can be recharged while using small home appliances and digital devices is increasingly important. Along with this increase, secondary battery performance tests require various test methods such as characteristics, lifespan, failure diagnosis, and recycling. In addition, the construction of a battery test system to ensure the safety and proper functioning of the battery, along with guidelines and correct basic knowledge are being considered. Therefore, in this paper, we will examine the characteristics of the secondary battery Li-ion battery according to the charging and discharging scenarios directly connected to the performance of the battery.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.2
• /
• pp.82-90
• /
• 2015

This paper proposes an efficient bi-directional DC/DC converter topology using multi-phase interleaved method for power storage system. The proposed converter topology is used for a power storage system using a vanadium redox flow battery(VRFB) and is configured to enable bidirectional power flow for charging and discharging of VRFB. Proposed DC/DC converter of the 4 leg method is reduced to 1/4 times the rating of the reactor and the power semiconductor device so can be reduce the system size. Also, proposed topology is obtained the effect of four times the switching frequency as compared to the conventional converter in each leg with a 90 degree phase shift 4 leg method. This can suppress the reduction of the life of the secondary battery because it is possible to reduce the current ripple in accordance with the charging and discharging of VRFB and may increase the efficiency of the entire system. In this paper, it proposed bidirectional high-efficiency DC/DC converter topology Using multi-phase interleaved method and proved the validity through simulations and experiments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.519-522
• /
• 2001

Recently, the battery charging technology and reducing technology of harmonics on AC input line are rising importantly according to increasing electrical facilities that it has been replaced battery with emergency power. In this study, I proposed that an auto-charging circuit of battery has low cost with simple-construction circuit, relative, harmonics reduction with diode tap-change method, high reliability of system for using characteristics of thyristor switching. In case of this circuit, convenience and reliability of maintenance of battery power units were more improved. 1 think that it is resulted in effect of prevention to shortening of battery life from over-charging and over-discharging and decrease of harmonics obstacle on AC input line.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.467-473
• /
• 2001

BMS(Battery Management System) in EV system(Electric Vehicle) senses voltage, temperature and the charging or discharging current of batteries. The main roles of BMS are to estimate SOC(State OF Charge) of batteries and optimally monitor them according to the operation state of EV system which is motoring mode or charging mode. In this paper, we propose the proper algorithm about BMS's roles and operation which is suitable to EV system and illustrate validity and effectiveness through the experiments which were performed in the condition of Vehicle road test and charging test.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.206-215
• /
• 1994

A method for simulating general characteristics and temperature characteristics of discharging SCR of the capacitor discharge impulse magnetizer-magnetizing fixture system using SPICE is presented. This method has been developed which can aid the design, understanding and inexpensive, time-saving of magnetizing circuit. As the detailed characteristic of magnetizing circuit can be obtained, the efficient design of the magntizing circuit which produce desired magnet will be possible using our SPICE modeling. Especially, computation of the temperature rise of discharging SCR is very important since it gives some indication of thermal characteristic of discharging circuit. It is implemented on a 486 personal computer, and the modeling results are checked against experimental measures. The experimental results have been achived using 305[V] and 607[V] charging voltage, low-energy capacitor discharge impulse magnetizer-magnetizing fixture of air cleaner DC motor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.1
• /
• pp.21-28
• /
• 2013

The paper proposes an optimal sizing method of a customer's battery energy storage system (BESS) which aims at managing the electricity demand of the customer to minimize electricity cost under the time of use(TOU) pricing. Peak load limit of the customer and charging and discharging schedules of the BESS are optimized on annual basis to minimize annual electricity cost, which consists of peak load related basic cost and actual usage cost. The optimal scheduling is used to assess the maximum cost savings for all sets of candidate capacities of BESS. An optimal size of BESS is determined from the cost saving curves via capacity of BESS. Case study uses real data from an apartment-type factory customer and shows how the proposed method can be employed to optimally design the size of BESS for customer demand management.