• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.182-192
• /
• 2015

This study develops a digital control scheme with power factor correction for a front-end converter in an electric vehicle battery charger. The front-end converter acts as the boost-type switching-mode rectifier. The converter assumes the two roles of the battery charger, which include power factor control and robust charging performance. The proposed control scheme consists of a charging control algorithm and a grid current control algorithm. The scheme aims to obtain unity input power factor and robust performance. Based on the linear average model of the converter, a constant-current constant-voltage charging control algorithm that passes through only one proportional-integral controller and a current feed-forward path is proposed. In the current control algorithm, we utilized a second band pass filter, a single-phase phase-locked loop technique, and a duty-ratio feed-forward term to control the grid current to be in phase with the grid voltage and achieve pure sinusoidal waveform. Simulations and experiments were conducted to verify the effectiveness of the proposed control scheme, both simulations and experiments.

• Journal of Power System Engineering
• /
• v.20 no.6
• /
• pp.58-63
• /
• 2016

A stainless steel has high corrosion resistance because of nickel in material, so it is used as materials for transportation and storage of hydrogen. In this study, TIG(tungsten ingot gas) welding was carried out on the stainless steel using the storage vessel of hydrogen. The microscopic structures at each region of TIG welded material such as HAZ, weld and base metals using optical microscope were observed. And the damage behavior of stainless steel that underwent the hydrogen charging using nondestructive evaluation was also studied. Ultrasonic test, which is the most generalized nondestructive technique, was applied to evaluate the relationship between the ultrasonic wave and mechanical properties at each zone of TIG welded stainless steel. The velocity and attenuation coefficients of ultrasonic wave didn't show a remarkable difference at each region of welded stainless steel. However, the attenuation coefficient was the highest at the weld zone when hydrogen charged stainless steel. In addition, acoustic emission test was also used to study the dynamic behavior of stainless steel experienced both hydrogen charging and weld. Lots of AE event at elastic region of stress-strain curve were occurred both the hydrogen charged specimen and the free specimen.

• Corrosion Science and Technology
• /
• v.10 no.4
• /
• pp.131-135
• /
• 2011

The demands of high-strength steel have been steadily increased to reduce the weight of vehicles. Although the TRIP steel has been the promising candidate material for the purpose, high strength hinders the application due to the susceptibility to hydrogen delayed fracture in the corrosive environment. Moreover, the testing method was not specified in the ISO standards. In this work, the test method to evaluate the susceptibility of hydrogen delayed fracture was studied by slow strain rate testing technique. The four test experimental parameters were studied : strain rate, hydrogen charging time, holding time after hydrogen charging, and holding time after cadmium plating. The steel was fractured by hydrogen in case the strain rate was in the range of $1{\times}10^{-4}{\sim}5{\times}10^{-7}/sec$. It was confirmed that the slow strain rate test is effective method to evaluate the susceptibility to hydrogen delayed fracture. The holding time over 24 hrs after hydrogen charging, nullified the hydrogen effect, that is, the specimen was no more susceptible to hydrogen after 24 hrs even though the specimen was fully hydrogen-charged. Moreover, cadmium electroplating could not prevent from diffusing out the hydrogen from the steel in the experiment. The effective experimental procedures were discussed.

• Resources Recycling
• /
• v.15 no.1 s.69
• /
• pp.28-36
• /
• 2006

The development of material separation technique for waste plastic recycling are the necessary situation restricted by law the reclamation and incineration of waste plastic after 2004, with enforcement of EPR (Extended Producer Responsibility) system. As the this study is the research on the development of electrostatic separation techniques for recycling of life circles waste plastic by development of charging material and charger, the separation efficiency can be improved. Therefore, we developed the charger and electrostatic separator to increase charging efficiency and material separation per object plastics, rising these equipments, we removed PVC up to $99\%$ from two kinds of mixed plastics. And in case of restricting PVC content such as PET, we developed the separation technique that can remove PVC up to $99.99\%$ from PET with PET recovery about $80\%$. Also, as we separated over $98\%$ for three kinds of mixed plastics, and then established material separation technique to increase recycling of plastic.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.23-33
• /
• 2005

The development of material separation technique for waste plastic recycling are the necessary situation according to restrict by law the reclamation and incineration of waste plastic after 2004 year, pith enforcement of EPR (Extended Producer Responsibility) system. As the this study is the research on the development of electrostatic separation techniques for recycling of life circles waste plastic, it can improve separation efficiency according to development of charging material and charger. Therefore, we developed the charger and electrostatic separator to increase charging efficiency and material separation per object plastics, using these equipments, we removed PVC up to 99% from two kinds of mixed plastics. And in case of restricting PVC content such as PET, we developed the separation technique that can remove PVC up to 99.99% from PET with PET recovery about 80%. Also, as we separated over 98% for three kinds of mixed plastics, and then established material separation technique to increase recycling of plastic.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.469-477
• /
• 2003

This paper proposes a Carrier-Rotation (CR) PWM technique that is a new solution for the voltage unbalancing problem of flying capacitors in the Flying Capacitor Multi-level Inverter (FCMI). The proposed technique equalizes the utilization of phase leg voltage redundancies corresponding to the charging and the discharging state of individual flying capacitors during each switching period of all the switches. Therefore, the charging and the discharging quantity of flying capacitors are equal, which makes the average variation of flying capacitor voltages become zero and keeps their voltage stable during minimum specified period. It also has the reduced harmonic contents of output voltage and the same switch utilization since all the carrier signals are in phase and the switching frequency of each switch is identical. The proposed technique is analyzed precisely in flying capacitor 3-level inverter and then it has expanded to the FCMI (N-level, N>3). Experimental results on the laboratory prototype flying capacitor 3-level inverter confirm the validity of the proposed technique.

• Korean Journal of Microbiology
• /
• v.24 no.2
• /
• pp.79-85
• /
• 1986

We have determined the sequence of $tRNA^{Arg}$ of A. nidulans partially by enzymatic rapid RNA sequencing technique. The sequence was 5'GGCCGGCUGGCCCAAXUGGCAAGGXUCUGAXUACGAAXCAGGAGAUUGCACXXXXXGAGCXXUXXGUCGGUCACCA3' The cloverleaf structure was made from above data. As a result, the anticodon sequence was identified as ACG. This result was confirmed with charging test. The complete sequence was proposed by supplementing the DNA sequence to and by assigning the position of minor bases to this RNA sequence.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1438-1445
• /
• 2015

A new DC-DC power converter is researched for renewable energy and battery hybrid power supplies systems in this paper. At the charging mode, a renewable energy source provides energy to charge a battery via the proposed converter. The operating principle of the proposed converter is the same as the conventional DC-DC buck converter. At the discharging mode, the battery releases its energy to the DC bus via the proposed converter. The proposed converter is a non-isolated high step-up DC-DC converter. The coupled-inductor technique is used to achieve a high step-up voltage gain by adjusting the turns ratio. Moreover, the leakage-inductor energies of the primary and secondary windings can be recycled. Thus, the conversion efficiency can be improved. Therefore, only one power converter is utilized at the charging or discharging modes. Finally, a prototype circuit is implemented to verify the performance of the proposed converter.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.216-219
• /
• 1999

A simple two-terminal cyclic current-voltage(I-V) technique is used to measure the current-transients in MOS capacitors. Distinct charging/discharging currents were measured and analyzed as a function of (1) the hold time. (2) the gate polarity during the FNT electron injection, (3) the injection fluence and (4) the annealing time after the injection had stopped. Discharging and charging current-transients were strongly dependent upon the conditions for forming the inversion layer and the density of interface traps caused during the FNT electron injection, respectively. Several tentative mechanisms were suggested in the current work.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.255-258
• /
• 2008

In this paper, the battery charging device using DMFC(Direct Methanol Fuel Cell) for electric bicycle is proposed. In the proposed system, phase-shift full-bridge converter is used as a battery charger by boosting the 12V DMFC output voltage up to 36V. By using the phase-shift technique, the ringing of the transformer is reduced and the efficiency of the converter can be improved. The operation modes of proposed phase-shift full-bridge converter is analyzed and verified by the simulation and the experimental results.