• 전기학회논문지
• /
• 제60권1호
• /
• pp.124-130
• /
• 2011

In this paper, We design and implementation of Self-Charging Module for charging to battery which obtaining the environment inergy such as solar energy. The power chared battery through the charging module send to sensor node. And implementation of System Activation Module(SAM) based on ID system and Dynamic Power Management Module(DPM) with SPO(Self Power Off). This system consume power only communication between the sensor nodes. We verification this system by implementing the high efficiency poweer management system.

• 한국재료학회지
• /
• 제31권2호
• /
• pp.84-91
• /
• 2021

To cope with automobile exhaust gas regulations, ISG and charging control systems are applied to HEV vehicles for the purpose of improving fuel economy. These systems require quick charge-discharge performance of high current. Therefore, a Module of the AGM battery with high energy density and EDLC(Electric Double Layer Capacitor) with high power density are constructed to study the charging and discharging behavior. In CCA, which evaluates the starting performance at -18 ℃ & 30 ℃ with high current, EDLC contributed for about 8 sec at the beginning. At 0 ℃ CA (Charge Acceptance), the initial Charging current of the AGM/EDLC Module, is twice that of the AGM lead acid battery. To play the role of EDLC during high-current rapid charging and discharging, the condition of the AGM lead-acid battery is optimally maintained. As a result of a Standard of Battery Association of Japan (SBA) S0101 test, the service life of the Module of the AGM Lead Acid Battery/EDLC is found to improve by 2 times compared to that of the AGM Lead Acid Battery.

• Journal of Biosystems Engineering
• /
• 제43권2호
• /
• pp.94-102
• /
• 2018

Purpose: In this study, a maintenance free super-capacitor battery charging system based on the photovoltaic module, to be used in agricultural electric carriers, was developed and its charging characteristics were studied in detail. Methods: At first, the electric carrier system configuration is introduced and the electric control components are presented. The super-capacitor batteries and photovoltaic module used in the experiment are specified. Next, the developed charging system consisting of a constant current / constant voltage Buck converter as the charging device and a super-capacitor cell as a balancing device are initiated. The proposed circuit design, a developed PCB layout of each device and a proportional control to check the current and voltage during the charging process are outlined. An experiment was carried out using a developed prototype to clarify the effectiveness of the proposed system. A power analyzer was used to measure the current and voltage during charging to evaluate the efficiency of the energy storage device. Finally, the conclusions of this research are presented. Results: The experimental results show that the proposed system successfully controls the charging current and balances the battery voltage. The maximum voltage of the super-capacitor battery obtained by using the proposed battery charger is 16.2 V, and the maximum charging current is 20 A. It was found that the charging time was less than an hour through the duty ratio of 95% or more. Conclusions: The developed battery charging system was successfully implemented on the agricultural electric carriers.

• 에너지공학
• /
• 제29권1호
• /
• pp.44-51
• /
• 2020

ESS의 중요성은 네트워크 신뢰성 저하 및 재생 가능 에너지원의 확장으로 인한 전력 수요의 안정화로 인해 강조되었다. ESS (Energy Storage System)는 남은 전력을 저장하고 전력 수요를 충족시키기 위해 필요할 때 이를 사용하며 주로 태양 광 및 풍력과 연계하여 ESS 시스템을 구축한다. 본 논문에서는 낮은 일사량에 효과적인 Master-Slave 방법을 이용한 가정용 PV 충전 모듈을 제안한다. 모듈을 설계 한 후 고속 MPPT 알고리즘이 적용되어 PV 모듈의 비선형 출력 특성에서 최대 출력을 생성한다. PV 충전 모듈의 입력에 대한 평균 전력 값은 296.90 W, 출력 전력은 289.60 W로 평균 97.54 %의 전력변환 효율을 보인다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.192-194
• /
• 2006

To elucidate possible challenges for outdoor practical use of dye-sensitized solar cells(DSC), compared with conventional Si solar cells. DSC modules still need the larger area than conventional Si solar modules to attain the same rated output because of lower photoelectron-chemical conversion efficiency. However, using batteries backup systems, the measured data shows that DSCs gathered over 12% more electricity than Si solar cells of the same rated output power in same outdoor condition. Moreover, battery charging time of DSC is about 1 hour faster than same rate of Si solar module. In this paper, 12 single DSC cells prepared for 4 serialized DSC cells was connected in 3 row parallel which have same output power rate of Si solar module. This DSC module was practiced generating characteristic experiment over outdoor daylight condition and applied with PV battery charger by using DC-DC converter. The main advantages of DSC module battery charger as compared with conventional Si solar module one are shorter charge time and lower cost.

• 전기학회논문지P
• /
• 제53권4호
• /
• pp.190-194
• /
• 2004

In this paper, UPS, which is embedded in computer power supply, is developed against the poor utility power system. In the developed system, PIC16C54 is used as the main controller, and UPS system consists of micom control module, power failure detecting module, charging module, power module, synchronous transfer module, and GUI module. Additionally, GUI module consists of battery charging state unit, power operating unit and operating state unit. The effectiveness of the developed system has been verified by the experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2288-2291
• /
• 2004

In this paper, UPS, which is embedded in computer, is developed against the poor utility power system. In the developed system, PIC16C74A is used as the main controller, and UPS system consists of micom control module, power failure detecting module, charging module, power module, synchronous transfer module, and GUI module. Additionally, GUI module consists of battery charging state unit, power operating unit and operating state unit.

• 한국정보전자통신기술학회논문지
• /
• 제16권2호
• /
• pp.104-108
• /
• 2023

최근 전기 차 시장의 확대로 인해 성능 및 안정성 문제를 보완할 친환경적인 전기 차 시장이 매우 커지고 있다. 전기 차의 화재 등 여러 안전 문제를 일으키는 전장 부품의 연동으로 인한 EMI 문제는 매번 대두되어 지고 있다. 다양한 기술들을 결합하여 최적의 충전효율을 달성하고 무선 충전 컨트롤 모듈에서 발생하는 EMI 잡음을 줄이기 위해 노력하고 있다. 본 논문은 전기자동차의 중요한 부품 중 하나인 무선충전컨트롤 모듈의 EMI 잡음 중 방사성 잡음 저감 기술을 설계하여 실험을 하였다. 무선 충전 컨트롤 모듈에서 발생하는 EMI 문제를 분석하기 위해 Ansys 시뮬레이션 툴 내 Python 기반 스크립트 기능을 활용하여 치명적인 요인에 대한 축적된 시험 데이터를 학습시켜 강화 학습을 통한 최적화 설계 기술을 적용하여 최적화된 무선충전컨트롤 모듈은 일반적인 무선충전 컨트롤 모듈 대비 25dBu V/m의 EMI 잡음 개선 효과를 보였다. 이러한 결과는 전기 자동차에서 더 안정적이고 신뢰성 높은 무선 충전 기능의 개발에 기여할 뿐만 아니라, 이를 통해 전기자동차의 사용성과 효율성을 높이며 환경친환적인 대안으로 자리 잡을 수 있게 한다.

• 설비공학논문집
• /
• 제16권8호
• /
• pp.741-747
• /
• 2004

The purpose of this study was to develop a cooler/heater using a thermoelectric module combined with a parallel flow type oscillating heat pipe with R-142b as a work ing fluid. The experiment was performed for 16 thermoelectric modules (6 A/15 V, size: 40${\times}$40${\times}$4 mm), varying design parameters of the heat pipe (inclination angle, working fluid charging ratio, etc) . Experimental results indicate that the optimum charging ratio and the inclination angle of the parallel flow type oscillating heat pipe were 30% by volume and 30%, respectively. The maximum cooler/heater capacity were 479W (COP : 0.47) and 630W (COP : 0.9), respectively.

• 전기화학회지
• /
• 제25권3호
• /
• pp.119-124
• /
• 2022

하이브리드 자동차 및 전기 자동차(하이브리드 및 전기자동차)용 배터리 팩은 고용량 대면적 셀을 적용하기 때문에 배터리 셀의 평균 온도는 중요한 관리 기준이 된다. 최근에는, 배터리 충전시간을 줄이기 위한 고속 충전 기술이 요구되고 있으며, 이에 따른 셀과 전장부품의 발열로 인해 배터리 팩 성능 및 수명의 저하가 발생한다. 따라서, 고속 충전에 따른 배터리 팩의 성능저하를 방지하기 위해 효과적인 배터리 냉각시스템이 필요하다. 본 연구에서는 파우치형 고속 충전용 배터리 셀 적용 냉각시스템 및 모듈 설계를 도출하고 배터리의 효율을 극대화할 수 있는 냉각성능을 분석하였다. 베이퍼챔버 냉각시스템을 적용한 모듈의 온도 편차 분석 결과 모듈 내 온도 편차는 5.82 ℃로 기존 알루미늄 냉각판 대비 낮은 온도를 보여 우수한 냉각시스템 효과를 보였다.