• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10A
• /
• pp.1031-1036
• /
• 2006

This paper proposes a novel BPF structure with less insertion loss and small size instead of the existing coupled line BPF for the output of the tripler using APDP (Anti-Parallel Diode Pair). This proposed BPF consists of the interdigital capacitor and spiral open stub. The proposed BPF has the insertion loss of less than 0.7dB within the band $(16.41{\sim}19.23GHz)$. The conversion loss of the tripler is about $16.6{\sim}18.5dB$ $(flatness<{\pm}1dB)$ at $5.72{\sim}6.28GHz$ of fundamental frequency. Its fundamental frequency and the fifth harmonic suppression characteristic at 6GHz are -32.16dBc and -44.6dBc, respectively And its phase noise attenuation characteristic is about 9.5dB at 100kHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.983-990
• /
• 2004

In this paper, we calculated the input impedance of the power line communication(PLC) networks using medium voltage power line. First of all, we proposed input and output teoninal model of PLC network, and calculated the input impedance applying the attenuation constants by radiation loss, conductor loss, dielectric loss. From the calculation result, we knew that the attenuation by radiation loss was largest, and the input impedance appears like a standing wave fonn with a fixed cycle because the high reflection at the input terminal for the characteristic impedance of the power line is very large. And also the cycle of input impedance depends on the coaxial cable length, and the amplitude depends on the characteristic impedance of power line and losses. From the measurement result, calculated result was very similar to the measured result.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.5
• /
• pp.473-477
• /
• 2005

A Bi-2223 tape has been developed for power applications such as a fault current limiter, a power cable and a superconducting magnetic energy storage system. In such applications, the Bi-2223 tape carries time varying transport current and in addition experiences time varying external magnetic field. It is well known that the external magnetic field not only causes magnetization loss in the Bi-2223 tape, but also drastically increases transport loss due to a so-called 'dynamic resistance' We developed an evaluation setup, which can measure transport loss in external at magnetic fields. Using this equipment, we measured the dynamic resistances for various amplitudes and frequencies of an external at magnetic field perpendicular to the face in the tape. Simultaneously we investigated the effect of an external ac field on transport loss with different experimental conditions. This paper describes test results ana discussions on correlation between the dynamic resistance and the transport loss for the Bi-2223 tape.

• Journal of Korean Society for Quality Management
• /
• v.48 no.4
• /
• pp.535-552
• /
• 2020

Purpose: The main theme of this study is to derive a specific quality loss function with multiple characteristics according to the same analytical structure as the single characteristic quality loss function of Taguchi. In other words, it presents an analytical framework for measuring quality costs that can be controlled in practice. Methods: This study followed the analytical methodology through geometric, linear algebraic, and statistical approaches Results: The function suggested by this study is as follows; $$L(x_1,x_2,{\cdots},x_t)={\sum\limits_{i=1}^{t}}k_i\{x_i+{\sum\limits_{j=1}^{t}}\({\rho}_{ij}{\frac{d_i}{d_j}}\)x_j\}x_i$$ Conclusion: This paper derived the quality loss function with multiple quality characteristics to expand the usefulness of the Taguchi quality loss function. The function derived in this paper would be more meaningful to estimate quality costs under the practical situation and general structure with multiple quality characteristics than the function by linear algebraic approach in response surface analysis.

• Journal of Advanced Navigation Technology
• /
• v.21 no.6
• /
• pp.626-632
• /
• 2017

This paper describes a high power amplifier combining eight low power amplifiers using a radial power combiner with low insertion loss. The radial power combiner is a non-resonant type combiner with 8 input ports and is implemented by microstrip transmission line. The combiner characteristics designed at operating frequency of 1.045 GHz have an insertion loss of 0.7 dB and a return loss of more than 12 dB. Also, the low power amplifier used was designed with AFT27S010NT1 transistor and designed to satisfy the same gain, phase and constant output characteristic at operating frequency. The high power amplifier, which combiners the radial power combiner and the drive amplifier of 8 W output by driving low power amplifiers obtained the output characteristic of 33 W at operating frequency of 1.045 GHz. Also, the change of the output characteristic of the amplifier using the radial combiner was graceful degradation when the low power amplifier failed one by one.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1629-1638
• /
• 1990

Using a 1/10 scale model pump, which is designed and manufactured to simulate two phase performance of reactor coolant pump of Y.G.N

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.323-337
• /
• 2009

This paper researched the adiabatic characteristic, safety and sound insulation characteristic of rolling stock window pane type and transition process of korean train vehicle window glass, and also including investigating a hereafter course of development. The window pane have provided the romantic feeling and the external scenery of train travel to the passenger in period of korea 110 year railway history. From the adiabatic viewpoint, this paper reviewed heat conductivity(U-value) and solar factor according to window pane type, including the safety and sound transmission loss of window pane.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 1998.11a
• /
• pp.610-621
• /
• 1998

In parameter design introduced by Taguchi, we analyze a signal-to-noise(SN) ratio. The SN ratio is a function of the expected loss due to the variation of quality characteristic. In this paper, an easy way for developing SN ratios is presented, which can be used to several quality characteristics simultaneously in parameter design. To develop such multivariate SN ratios, the transformation method of the expected loss and combining techniques are employed. And the analysis of real empirical data for an application of the proposed method is also presented.

• Journal of KSNVE
• /
• v.11 no.1
• /
• pp.29-35
• /
• 2001

Recently, the porous duct is becoming one of Possible ways to reduce the intake noise of an automobile instead of using resonators. In this article, acoustic characteristic of the porous duct is investigated theoretically and experimently. Futhermore, 4-pole parameter of the porous duct is introduced to predict transmission loss of it for various case. Acoustic efficiency of the porous duct is shown with experimental result using a car.

• Journal of Korean Society for Quality Management
• /
• v.27 no.3
• /
• pp.67-78
• /
• 1999

In parameter design introduced by Taguchi, we analyze a performance measure, so called SN ratio. The SN ratio is a function of the expected loss due to the variation of quality characteristic. In this paper, an easy way for developing performance measures is presented, which can be used to control several quality characteristics simultaneously in parameter design. To develop such multivariate performance measures, the transformation method of the expected loss and combining techniques are employed. And the analysis of real empirical data for an application of the proposed method is also presented.