• Applied Chemistry for Engineering
• /
• v.22 no.3
• /
• pp.286-290
• /
• 2011

Syngas was produced out of pellet refuse derived fuel (RDF) produced from an RDF production facility of W city, Korea. A two-stage gasification system was developed to use the RDF char as an auxiliary heat source for gasification reaction. The composition and heating value of syngas as well as the heating value of residual product (char) were measured at a different residence time to investigate the optimal operating condition of the two-stage gasification system for syngas production. The optimal char residence time to minimize the energy cost due to an external heat source supply was also deduced.

• Elastomers and Composites
• /
• v.52 no.2
• /
• pp.143-153
• /
• 2017

Herein we studied the characterization of the PBO films formed via solution casting and thermal cyclization of poly(o-hyroxyamide)s(PHAs) that were synthesized by direct polycondensation of 3,3'-dihydroxybenzidine with 4,4'-(2,3-quinoxalinedioxy) dibenzoic acid and/or 4,4'-(2,3-pyridinedioxy) dibenzoic acid. All the PHAs exhibited inherent viscosities in the range of 0.55~0.84 dL/g in DMAc solution. The copolymers, CPH-2-5, were partially soluble in less polar solvents like pyridine and THF. However, all the PBOs were not soluble in polar solvents, but only partially soluble in sulfuric acid. The temperatures corresponding to 10% weight loss of the PBOs with increasing content of quinoxalinedioxy unit were higher than those of the PHAs, and the char yields at $900^{\circ}C$ in $N_2$, tensile strength, and initial modulus of the PBOs were 1.1~1.3 times, 1.2~1.8, and 1.6~3.3 times higher, respectively, than those of the PHAs. The LOI value of CPB-2 was 38.5%, while that of CPB-1 was the highest at 40.0%. The LOI test confirmed that excellent flame retardants were synthesized.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.1
• /
• pp.89-96
• /
• 2016

The mechanism for laminar dust flame propagation can only be elucidated from a comprehensive mathematical model which incorporates conduction and radiation, as well as the chemical kinetics of particle devolatilization and gas phase and char reaction. The mathematical model for a flat, laminar, premixed coal-air flame is applied to the atmospheric coal-air mixtures studied by Smoot and co-workers, and comparisons are made with their measurements and predictions. Here the principal parameter for comparison is the laminar burning velocity. The studies of Smoot and co-workers are first reviewed and compared with those predicted by the present model. The effects of inlet temperature and devolatilization rate constants on the burning velocities are studied with the present model, and compared with their measurements and predictions. Their measured burning velocities are approximately predicted with the present model at relatively high coal concentrations, with a somewhat increased inlet temperature. From the comparisons, their model might over-estimate particle temperature and rates of devolatilization. This would enable coal-air mixtures to be burned without any form of preheat and would tend to increase their computed values of burning velocity.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.5
• /
• pp.907-918
• /
• 2000

The pyrolysis characteristics of celluloses and plastics, which are the principal materials contributing to the municipal solid wastes(MSWs), was investigated with a thermal gravimetric analysis reaction system. The experiments were carried out in a nitrogen atmosphere in the temperature range of 400~900K at various experimental conditions. Also, a modified pyrolysis model for compressed MSWs has been proposed. Varing the heating rate to 20, 30, 40K/min, reaction orders of MSWs' main component were around 1.1~1.9, activation energies were 117~166kJ/mol for celluloses and 187~239kJ/mol for plastics. Char yield was proportional to the heating rate, particle size, and compressed ratio. The model proposed in this study, which is applying Arrhenius equation and thermodynamics, is closer to the experimental results than the conventional model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2550-2558
• /
• 2013

Poly(o-hydroxyamides)(PHAs) copolymers having oligo(oxy ethylene) pendant in the main chain were synthesized by solution polycondensation reaction at low temperature. Copolymer precursors were studied by fourier transform infrared(FT-IR), differential scanning calorimeter(DSC), thermogravimetric analyzer(TGA), universal testing machine(UTM) and limited oxygen index(LOI). The inherent viscosities of the PHAs measured at $35^{\circ}C$ in DMAc or DMAc/LiCl solution were in the range of 0.74~1.42 dL/g. Solubility of the precursors with higher oligo(oxy ethylene) unit was increased, but the PBOs were nearly insoluble in a variety of solvents. The degradation temperature of the copolymer precursors was recorded in the ranges of $408{\sim}664^{\circ}C$ in nitrogen and char yields showed 13~59% values at $900^{\circ}C$. The mechanical properties and flame retardancy of copolymer precursors decreased with higher oligo(oxy ethylene) unit.

• Journal of Energy Engineering
• /
• v.20 no.4
• /
• pp.309-317
• /
• 2011

The effect of physical properties of coal fuels and carbon particle on performance of DCFC (Direct Carbon Fuel Cell) was investigated. Shenhua and Adaro were selected as coal fuel and carbon particle was used for comparing with coal. The Ultimate, proximate, SEM, XRD, and BET analysis of samples were conducted. The component of char was more important than that of raw coal because the operating temperature of reactor is higher than devolatilization region of coal. The surface area and volume of pores affected significantly the performance of the system than content of fixed carbon or char rates. The performance of DCFC with carbon particle was in proportional to working temperature.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.36-42
• /
• 2019

In this study, the pre-treatment of lyocell fabrics was performed using phosphoric acid (PA) as a phosphorus flame retardant and melamine resin (MR) as a cross-linking agent to fabricate carbon fabrics using lyocell fibers. The physical and chemical changes were investigated by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffractometry (XRD) and weight analysis. We confirmed that the weight yield of the carbon fabrics compared to the untreated fabrics increased by 14.7%, and width and length yield of the fabrics increased by 15% and 15.5%, respectively. This may be due to the effect of promoting the dehydration reaction of cellulose, forming char on the fiber surface, which induces a crosslinking reaction in the cellulose molecule and stabilizes the structure upon pyrolysis.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.131.2-131.2
• /
• 2010

서부 발전 태안화력발전소에 건설 예정인 IGCC Demo plant의 설계 자료를 근거로 석탄 가스화기의 정상 상태 전산모사를 PRO/II를 사용하여 수행하였다. 석탄을 PRO/II가 받아들일 수 있는 성분으로 바꾼 후 가스화기를 버너와 가스화기 본체의 두 부분으로 나누어 모델링하였다. 버너는 단열조건의 Gibbs Reactor로 모델링하였다. 모사 결과 산소가 완전 소진될 때까지 반응이 진행되는 것을 확인하였다. 가스화기는 char gasification 반응은 kinetic reaction equation으로, gas phase reaction은 equilibrium reactor로 모사하는 알고리듬을 개발 하였으나 PRO/II의 기능에 한계가 있어 간단한 Gibbs Reactor로 모사하였다. 가스화기는 membrane wall에 의하여 냉각되는 것을 고려하여 $1550^{\circ}C$의 균일한 온도에서 반응이 일어나는 것으로 고려하였다. 전산 모사 결과 주요 성분의 조성이 실제 syngas의 조성과 5% 정도 오차가 있는 것으로 나타났다.

• 한국연소학회:학술대회논문집
• /
• 1999.10a
• /
• pp.155-163
• /
• 1999

A numerical study for simulating a swirling pulverized coal combustion in axisymmetric geometry is done here by applying the weighted sum of gray gases model (WSGGM) approach with the discrete ordinate method (DOM) to model the radiative heat transfer equation. In the radiative transfer equation, the same polynomial equation and coefficients for weighting factors as those for gas are adopted for the coal/char particles as a function of partial pressure and particle temperature. The Eulerian balance equations for mass, momentum, energy, and species mass fractions are adopted with the standard ${\kappa}-{\varepsilon}$ turbulence model, whereas the Lagrangian approach is used for the particulate phase for soot. The eddydissipation model is employed for the reaction rate for gaseous mixture, and the single-step first-order reaction model for the devolatilization process for coal. By comparing the numerical results with experimental ones, the models used here are confirmed and found to be one of good alternatives for simulating the combustion as well as radiative characteristics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1101-1109
• /
• 2010

We investigated the combustion rate and kinetic rate of char when burning in oxygen-enriched atmospheres with either an $N_2$ or $CO_2$ bath gas in a drop tube furnace. The experiments were performed with sub-bituminous coal (Adaro) and bituminous coal (Coal valley) under atmospheric pressure conditions. Two different coals were investigated over 12 to 30 vol% oxygen and furnace temperatures of 900, 1100, and $1300^{\circ}C$. For both coals, the particle temperature and overall reaction rate are lower in the $CO_2$ bath gas. However, analysis of single-particle data shows that the surface-specific burning rate of char oxidation is similar in both gases. In addition, the kinetic rate and activation energy for each coal were similar for both gases. Generally, the particle temperature and overall reaction rate of sub-bituminous coal are higher than those of bituminous coal.