• 동력기계공학회지
• /
• 제5권2호
• /
• pp.30-35
• /
• 2001

A comparison of fully developed heat transfer and friction factor characteristics has been made in rectangular ducts with one wall roughened by five different shapes. The effects of rib shape geometries and Reynolds number are examined. The rib height-to-duct hydraulic diameter, pitch-to-height ratio, and aspect ratio of channel width to height are fixed at $e/D_e=0.0476$, P/e=8, and W/H=2.33, respectively. To understand the mechanisms of the heat transfer enhancements, the measurements of the friction factors are also conducted in the smooth and rough channels. The data indicate that the triangular type rib has a substantially higher efficiency index than any other ones in the range we studied.

• The Journal of the Acoustical Society of Korea
• /
• 제16권3E호
• /
• pp.24-31
• /
• 1997

A mobile propagation characteristics for wideband DS-SS (Direct Sequence-Spectrum) signal is presented. Existing narrowband model is extended for the wideband pulse with an arbitrary shape. The received DS-SS signal in the frequency domain is the transfer function of the propagation channel weighted by the inverse Fourier transform. In this proposed method, received signal spectral density, instantaneous waveform, and Doppler spectrum of DS-SS signal via either Rayleigh of Rician channel can be obtained easily. Simulation results match well with both simulated theoretical fading statistics and classical theory. As expected, the extraction of chip timing in Rician fading shown to be more tractable than Rayleigh fading.

• 대한전자공학회논문지
• /
• 제25권7호
• /
• pp.780-790
• /
• 1988

We have studied the hot-carrier-induced degradation caused by the high channel electric field due to the decrease of the gate length of MOSFET used in VLSI. Under DC stress, the condition in which maximum substrate current occures gave the worst degradation. Under AC dynamic stress, other conditions, the pulse shape and the falling rate, gave enormous effects on the degradation phenomena, especially at 77K. Threshold voltage, transconductance, channel conductance and gate current were measured and compared under various stress conditions. The threshold voltage was almost completely recovered by hot-injection stress as a reverse-stress. But, the transconductance was rapidly degraded under hot-hole injection and recovered by sequential hot-electron stress. The Si-SiO2 interface state density was analyzed by a charge pumping technique and the charge pumping current showed the same trend as the threshold voltage shift in degradation process.

• Journal of Forest and Environmental Science
• /
• 제6권1호
• /
• pp.8-17
• /
• 1989

Recent development of industry and urbanization in the interior of mountainous area increases the possibility of occurence of natural disaster, such as flood, landslide and deblis-flow. Erosion control facilities, which were the most significant activity to riverbed fixiation, were constructed at the downstream of the experimental basin. In the mountain torrents, the complex bed load transport has occurred by the drift of running water, and resulting in a formation of terrace deposits. Especially, channel migration caused by scouring and deposition frequently occurs at the wide areas of the river bed. Consequently, the unsymmetrical river bed charactristics indicate the degree of the channel migration.

• 한국분말재료학회지
• /
• 제9권1호
• /
• pp.11-18
• /
• 2002

The 6061 Al alloy based composites reinforced with 10 vol% SiC whiskers were prepared by powder metallurgy with the powders having the different sizes, i.e. < $30{\mu}m$ and > $30{\mu}m$ The composites were subjected to equal channel angular pressing (ECAP) at various conditions and the microstructural changes during ECAP were examined In the composites SiC whiskers were clustered and randomly aligned. The clusters were relatively well distributed in the composite with the smaller initial powder size. After ECAP, the clusters were aligned parallel to flow direction and became smaller. In addition, the shape of clusters was changed from irregular to round. The microstructure of the ECAPed samples were compared with those of the conventionally hot-extruded composites. The uniform microstructure and enhanced microhardness could be obtained by using the powders having the smaller size, decreasing ECAP temperature and repeating ECAP.

• Korean Journal of Hydrosciences
• /
• 제8권
• /
• pp.41-56
• /
• 1997

A new routing computer model for the symmetric compound channel called the ASRMCS(Apparent Shear Force Muskingum-Cunge Method in Symmetry) has been developed. The Muskingum-Cunge routing method is adapted. The Apparent Shear Force (ASF) between the deep main channel and the shallow floodplan flow is introduced while the flow is routed. The nonlinear parameter method is applied. The temporal and spatial increments are varied according to the flow rate. The adaptation of above schemes is tested against the routed hydrographs using the DAMBRK model. The results of general routing practice of Muskingum-Cunge Method(GPMC) are also compared with those of above two models. The results of the new model match remarkably well with those of DAMBRK. The routed hydrographs show a smooth variation from the inflow boundary condition without any distortions caused by the difference of cross-section shape. However, the results of GPMC, showing early rise and fall of routed hydrograph, have considerable differences from those of the ASFMCS and DAMBRK.

• 한국재료학회지
• /
• 제16권1호
• /
• pp.68-74
• /
• 2006

2024 Al alloys were severely deformed by equal channel angular pressing(ECAP) to obtain an ultrafine grain structure. The more deformation amount increased, the more grain size decreased. Most of the grain structure were changed from elongated to equiaxed shape with increasing pass number. The morphology of S' phases was also changed from rod-type to spherical type. The grain size of 6 passed specimen was 100 to 200 nm, and the size of S' phases was about 10 nm in the microstructure. XRD measurements have revealed that the texture formed by plastic deformation disappeared in the 6 passed specimen. SP test results described that the start of crack propagation occurred at the transition zone between plastic bending and membrane stretching because of small elongation. The maximum strength of ECA pressed specimen increased 1.9 GPa to 2.9 GPa with increasing pass number.

• Journal of Magnetics
• /
• 제12권4호
• /
• pp.152-155
• /
• 2007

Spin dependent transport was investigated in lateral $Py(Ni_{81}Fe_{19})/Au/Py$ spin valve devices. Clear spin valve effect was observed in conventional four-terminal measurement geometry. Higher resistance was found in antiparallel magnetization field of two Py electrodes which is determined by anisotropy magnetoresistance (AMR) measurements. The rectangular shape of spin signal together with good agreement of switching field convinces observed spin valve signal is resulted from effective spin injection and detection. The magnetoresistance ratio decays exponentially with channel length by which spin diffusion length of Au channel was estimated to be 76 nm.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1172-1177
• /
• 2008

Diverging channel from gas burner exit to the inlet section of Heat Recovery Steam Generator (HRSG) has been re-designed for 1 MW steam supply and power generation system. Three different test geometries have been chosen for the numerical simulation. The existing design for 300 kW HRSG system (CASE B) has been improved by geometry and position changes of inlet guide vanes along with gas velocity entrance angle at the diverging channel inlet (CASE C). Both cases has been compared with the case where hot combustion gas is directly injected without any guide vanes (CASE A). Improved design shows overall uniform velocity and temperature distribution compared to existing design.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.413-416
• /
• 2009

The paper deals with the mechanical and electrical responses of submicrocrystalline Cu-3%Ag alloy as a function of strain imposed by equal-channel angular pressing. When inducing the effective strain of 12, the initial grain site of ${\sim}50{\mu}m$ is evidently reduced within the range of $0.2-0.3{\mu}m$ in size, having a reasonably equiaxed shape. The results of tension tests at room temperature exhibit that the tensile strength of the present alloy increases with increasing the amount of strain whereas losing electrical conductivity slightly. This phenomenon can be explained based on fine grained structure together with the non-equilibrium state of grain boundaries.