• Electrical & Electronic Materials
• /
• v.4 no.3
• /
• pp.259-266
• /
• 1991

1.5.mu.m의 찬넬길이를 갖는 short channel 비휘발성 SNOSFET 기억소자를 기존의 CMOS 1 Mbit 공정기술을 이용하여 제작하고 I$_{d}$-V$_{d}$ 및 I$_{d}$- V$_{g}$특성과 스윗칭 및 기억유지특성을 조사하였다. 그 결과 제작한 소자는 논리회로 설계에 적절한 전도특성을 가졌으며 스윗칭시간은 인가전압의 크기에 의존함을 보였다. 그리고 3V의 memory window 크기를 얻기 위해서 V$_{w}$ =+34V, t$_{w}$ =50.mu.sec 및 V$_{e}$=-34V, t$_{e}$=500.mu.sec의 펄스전압으로 각각 write-in과 erase할 수 있었다. 또한 기억상태는 10년이상 유지할 수 있음을 알 수 있었다.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.276-283
• /
• 1999

This study focuses on part quality and cycle times under gas-assisted injection molding (GIM) of box shape molded parts. The position of the gas channel was established near to parting line at the end of last locations to fill. Applied hot runner and valve gates, the gas was introduced directly into the mold cavity via gas pin. As GIM was applied, the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture. ii) The reliability was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout. iii) It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM. iv) The productivity were improved by reducing cycle times.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.11
• /
• pp.550-556
• /
• 2001

The computerized cardiac analysis system, which acquires and analyzes the electrical activation signal propagating along the surface of the heart, is indispensible equipment for the open heart surgery and electrical cardiac study. In this paper, the design requirement and the electrical circuit analysis are performed to construct the multi-channel cardiac activation pre-amplifier necessary for a signal conditioning circuit. The general 64 channel configuration is expanded into 128 channels to enhance the spatial resolution on the mapped surface of the heart. The 128 channels pre-amplifier consists of input circuit, differential amplifier, right leg driven circuit and isolation part. It has distinct features; high voltage protection, leakage current limitation, isolation and the maximization of common mode rejection ratio with respect to the half-cell potential difference due to different electrode materials. The final pre-amplifier circuit is assembled with 8 boards, each of which composing of 16 channels.

• Journal of Powder Materials
• /
• v.11 no.3
• /
• pp.233-241
• /
• 2004

In this study, bottom-up type powder processing and top-down type SPD (severe plastic deformation) approaches were combined in order to achieve both full density and grain refinement of Al-20 wt% Si powders without grain growth, which was considered as a bottle neck of the bottom-up method using the conventional powder metallurgy of compaction and sintering. ECAP (Equal channel angular pressing), one of the most promising method in SPD, was used for the powder consolidation. The powder ECAP processing with 1, 2, 4 and 8 passes was conducted for 10$0^{\circ}C$ and 20$0^{\circ}C$ It was found by microhardness, compression tests and micro-structure characterization that high mechanical strength could be achieved effectively as a result of the well bonded powder contact surface during ECAP process. The SPD processing of powders is a viable method to achieve both fully density and nanostructured materials.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.141-143
• /
• 2017

Novel structured thin film transistors (TFTs) of amorphous silicon zinc tin oxide (a-SZTO) were designed and fabricated with a thin metal layer between the source and drain electrodes. A SZTO channel was annealed at $500^{\circ}C$. A Ti/Au electrode was used on the SZTO channel. Metals are deposited between the source and drain in this novel structured TFTs. The mobility of the was improved from $14.77cm^2/Vs$ to $35.59cm^2/Vs$ simply by adopting the novel structure without changing any other processing parameters, such as annealing condition, sputtering power or processing pressure. In addition, stability was improved under the positive bias thermal stress and negative bias thermal stress applied to the novel structured TFTs. Finally, this novel structured TFT was observed to be less affected by back-channel effect.

• Transactions of Materials Processing
• /
• v.11 no.6
• /
• pp.519-528
• /
• 2002

The microstructural evolution during the equal channel angular pressing of Ti-6Al-4V alloy was investigated using the transmission electron microscopy (TEM). ECA pressing was carried out isothermally with route C at $600^{\circ}C$ for two types of initial microstructure, i.e., equiaxed and Widmanstatten microstructures. At an initial stage of ECA pressing, the equiaxed microstructure showed more uniform flow than the Widmanstatten microstructure. However, both microstructures were significantly refined revealing nearly equiaxed grains of 0.3$mu extrm{m}$ in diameter with high angle grain boundaries after 4 passes of ECA pressing. These ultrafine gains were found to be stable with little grain growth, when annealed up to $600^{\circ}C$ for 1hr.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.680-682
• /
• 2022

The closed-loop supply chain's central enterprises aim to maximize the revenue and reduce the reclaiming channel level to the greatest extent by using blockchain and modern management methods. The traditional recycling network has more links, and there is less communication between enterprises in each link. There is a particular "bullwhip effect" in the channel link, making it difficult for power battery manufacturers to respond to the dynamic market quickly. It is often challenging to obtain scaled waste power batteries, which aggravates how power battery raw materials are expensive and difficult to recycle. Therefore, the closed-loop supply chain design of power batteries adopting blockchain shall minimize channel links and reduce transaction levels to reduce costs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.340.2-340.2
• /
• 2014

최근 비정질 산화물 반도체는 가시광 영역에서의 투명도와 낮은 공정 온도, 그리고 높은 Field-effect mobility로 인해 Thin film transistors의 Active channel layer의 재료로 각광 받고 있다. ZnO, IZO, IGO, ITGO등의 많은 산화물 반도체들이 TFT의 채널층으로의 적용을 위해 활발히 연구되고 있으며, 특히 비정질 IGZO는 비정질임에도 불구하고 Mobility가 $10cm^2/Vs$ 정도로 기존의 a-Si:H 보다 높은 Mobility 특성을 나타내고 있어 대화면 디스플레이와 고속 구동을 위한 LCD에 적용 할 수 있으며 또한 낮은 공정 온도로 인해 플렉서블 디스플레이에 응용될 수 있다는 장점이 있다. 우리는 RF magnetron sputtering법으로 증착한 비정질 IGZO TFT(Thin Film Transistors)의 전기적 특성과 IGZO 박막의 특성에 미치는 RF power의 영향을 연구하였다. 제작한 TFTs의 Active channel layer는 산소분압 1%, Room temperature에서 RF power별(50~150 W)로 Si wafer 기판 위에 30nm로 증착 하였고 100 nm의 $SiO_2$가 절연체로 사용되었다. 또한 박막 특성을 분석하기 위해 같은 Chamber 분위기에서 100 nm로 IGZO 박막을 증착하였다. 비정질 IGZO 박막의 X-ray reflectivity(XRR)을 분석한 결과 RF Power가 50 W에서 150 W로 증가 할수록 박막의 Roughness는 22.7 (${\AA}$)에서 6.5 (${\AA}$)로 감소하고 Density는 5.9 ($g/cm^3$)에서 6.1 ($g/cm^3$)까지 증가하는 경향을 보였다. 또한 제작한 IGZO TFTs는 증착 RF Power가 증가함에 따라 Threshold voltage (VTH)가 0.3~4(V)로 증가하는 경향을 나타내고 Filed-effect mobility도 6.2~19 ($cm^2/Vs$)까지 증가하는 경향을 보인다. 또한 on/off ratio는 모두 > $10^6$의 값을 나타내며 subthreshold slope (SS)는 0.3~0.8 (V/decade)의 값을 나타낸다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.431-431
• /
• 2011

Graphene, two dimensional sheet of sp2-hybridized carbon, has attracted an enormous amount of interest due to excellent electrical, chemical and mechanical properties for the application of transparent conducting films, clean energy devices, field-effect transistors, optoelectronic devices and chemical sensors. Especially, graphene is promising candidate to detect the gas molecules and biomolecules due to the large specific surface area and signal-to-noise ratios. Despite of importance to the disease diagnosis, there are a few reports to demonstrate the graphene- and rGO-FET for biological sensors and the sensing mechanism are not fully understood. Here we describe scalable and facile fabrication of rGO-FET with the capability of label-free, ultrasensitive electrical detection of a cancer biomarker, prostate specific antigen/${\alpha}1$-antichymotrypsin (PSA-ACT) complex, in which the ultrathin rGO sensing channel was simply formed by a uniform self-assembly of two-dimensional rGO nanosheets on aminated pattern generated by inkjet printing. Sensing characteristics of rGO-FET immunosensor showed the highly precise, reliable, and linear shift in the Dirac point with the analyte concentration of PSA-ACT complex and extremely low detection limit as low as 1 fg/ml. We further analyzed the charge doping mechanism, which is the change in the charge carrier in the rGO channel varying by the concentration of biomolecules. Amenability of solution-based scalable fabrication and extremely high performance may enable rGO-FET device as a versatile multiplexed diagnostic biosensor for disease biomarkers.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1177-1189
• /
• 1994

This paper aims to develop the numerical model for prediction of the channel migration by analyzing of sediment and flow characteristics with patterns of channel in alluvial rivers. Flow in rivers constitutes to be the meandering or the braided form and rarely straight channel through morphologically stable patterns with mutual actions between the flowing water and bed materials. In order to develop the model for simulation of the channel migration, the channels are divided into two types with positive or negative sign by the direction of curvature radius of the centerline channel ($r_c$). That is, the single bend-channel consists of only one curvature of positive or negative sign and the multi-bend channel consists of two more curvatures of positive or negative sign, respectively. The model analyzes the sediment and flow characteristics under the influence of superelevation, spiral motion, irregularity in bed topography and depth-averaged velocity of channels. For reliability of this model, the single bend-channel and the multi bend channel are compared with experiment data in other models and the measured field data in the Keum-River, respectively. As a result, the both com parisians turn out to be excellent.