• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 A
• /
• pp.544-547
• /
• 2002

In a high power laboratory, artificial lines are used for SLF tests of circuit breakers. The line side PTRV is affected by the stray capacitances of testing and measuring equipment as well as the circuit parameters of artificial lines. The changing pattern of PTRV was examined, and the circuit parameters of artificial line for some examples were compensated using the changing pattern to satisfy test conditions specified.

• Journal of Magnetics
• /
• 제16권4호
• /
• pp.386-390
• /
• 2011

This paper deals with the magnetic equivalent circuit modeling and permanent magnet (PM) performance evaluations of a pole changing memory motor (PCMM). We use a coupled transient finite element method (FEM) and Preisach modeling, which is presented to analyze the magnetic characteristics of the permanent magnets. The focus of this paper is on the evaluation of characteristics such as the magnetizing direction and the pole number of the machine under re- and de-magnetization conditions.

• 전자공학회논문지S
• /
• 제35S권9호
• /
• pp.111-117
• /
• 1998

본 논문은 LC공진회로를 이용한 사이크로컨버터의 휴지기간 없는 극성절환 방법에 관한 것이다. 제안한 방법에 따르면 극성절환시 회로단락을 방지하기 위한 휴지기간이 요구되지 않는다. 따라서 제어지연 및 출력전류의 고조파성분이 감소하게 된다. 그리고 제안한 방법은 비순환전류형의 다른 자연전류형 사이크로컨버터에도 확장될 수 있다. 본 논문에서는 휴지기간 없는 극성절환의 스위칭 방법에 대하여 검토하였으며 제안한 방법의 유용성을 확인하기 위하여 LC공진회로를 이용한 사이크로콘버터에 적용실험을 수행하였다.

• 전자공학회논문지SC
• /
• 제40권6호
• /
• pp.16-23
• /
• 2003

본 논문에서 보청기를 위한 개별 BJT 소자의 효과적인 바이어스 회로를 제안한다. 보청기에 널리 사용되는 컬렉터 귀환 바이어스 회로는 부귀환 저항을 가지고 있다. 이 저항은 AC와 DC에 동시에 영향을 줌으로서 DC 바이어스 점의 변화 없이 증폭기의 이득을 변화시키기 어렵다. 또한 기존회로는 보청기의 이득이 높을 경우 전원 잡음의 정귀환으로 발진할 수 있는 단점이 있다. 제안된 회로는 컬렉터 귀환 바이어스회로에 베이스와 전원 사이에 컬렉터 저항보다 β배 더 큰 저항을 추가하여 기존회로의 두 가지 단점을 줄일 수 있다. 제안된 회로에서 DC 바이어스 점의 변화 없이 증폭기의 이득을 변경 할 수 있고 모의실험에서 기존회로보다 전원 잡음 이득을 18.5%정도 감소시킬 수 있다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권6호
• /
• pp.267-272
• /
• 2002

This Paper deals with the short circuit tests of the three-Phase DC reactor type fault current limiter (FCL) in changing of turns ratio of transformers. The experiment of this paper is a preliminary step to develop the FCL's faculties for an application to high voltage transmission line. So, superconducting coil was made of Nb-Ti, low temperature superconductor, and the ratings of the power system of experimental circuit are 400V/7A class. A three-phase DC reactor type FCL consists of three transformers, six diodes, one superconducting coil and one cryostat. The important point of experimental analysis is transient period, the operating lagging time of circuit breaker. As the results of the experiment, the values are referred to the limitation rate about 77% and 90% when the turns ratio of transformer was 1:1 and 2:1 respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권1호
• /
• pp.61-73
• /
• 1985

The induction motor is widely used in the power equipments of the ship and the various industrial drive applications because it is robust and relatively simple and cheap to manufacture, but it has a disadvantage that the speed of induction motor is not controlled in wide range such as d.c motor. In this paper, the characteristics relating to the Kramer system that the speed of three phase wound type induction motor is controlled by changing the exciting e.m.f. of the secondary circuit is described. In order to analyze the characteristics, a new simplified and approximated T-type equivalent circuit from the Kramer circuit with three phase graetz connection and d.c machine is proposed. The stator current, motor torque and mechanical output power are computed by the current, torque and power equations derived by its equivalent circuit. Through the experiments, the $I_f-N$, torque-slip and current-slip characteristic curves of the tested motor are obtained and the various needed constants are determined. The numerical values obtained from the above method are compared with experimental values under the same conditions. As a result of the above investigation, it is found that the induction motor speed by the Kramer system is controlled by 28 per cent under the rated speed by changing the field current of d.c motor and the values computed by the current and torque equations derived by the simplified and approximated T-type equivalent circuit generally come to approach the experimental values.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.235-240
• /
• 2002

In micro-EBM, it is well blown that RC circuit is suitable for discharge circuit because of its low pulse width and relatively high peak current. To increase machining speed without changing unit discharge energy, charge resistance should be decreased. But, if very low, continuous (or normal) arc discharge occurs, then increases electrode wear and reduces machining speed remarkably. In this paper, RC circuit with transistor is used to micro-EDM. Experimental results show that RC circuit with transistor can cut off continuous (or normal) arc discharge effectively if duty factor and switching period of transistor are set up optimally. Through experiments with varying charge resistance, it can be known that RC circuit with transistor has about two times faster machining speed than that of RC circuit. Especially, it has prominent rise-effect of machining speed in low unit discharge energy, so that a high-quality and high-speed micro-EDM can be realized through RC circuit with transistor.

• 한국정밀공학회지
• /
• 제21권12호
• /
• pp.44-51
• /
• 2004

In a micro-EDM, it is well known that an RC circuit is suitable as a discharge circuit because of its low pulse width and relatively high peak current. To increase machining speed without changing unit discharge energy, charge resistance should be decreased. But, when the resistance is very low, continuous (or normal) arc discharge occurs, electrode wear increases and machining speed is reduced remarkably. In this paper, an RC circuit with transistors is used in a micro-EDM. Experimental results show that the RC circuit with transistors can cut off a continuous (o. normal) arc discharge effectively if the duty factor and switching period of the transistor are set up optimally. Through experiments with varying charge resistances, it is shown that the RC circuit with transistors has about two times faster machining speed than that of an RC circuit.

• 대한전기학회논문지
• /
• 제36권12호
• /
• pp.868-873
• /
• 1987

In this pater, we have proposed a synthetic main chopper circuit for the chopper controlled electric automobile. The proposed chopper circuit operates as a step-down chopper in powering mode and as a polarity reversion type chopper in regenerative braking mode. In this study, it was found that powering and regenerative braking operations using the separately excited D.C motor can be controlled continuously only by gate signals of the chopper without changing the connection of the circuit.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.99.2-99
• /
• 2001

An electronically tunable current-mode second-order multifunctional filter is described in this paper. The proposed filter consists of two four-terminal floating nullors (FTFNs), two dual-output OTAs and two grounded capacitors. The circuit can simultaneously realize the lowpass, bandpass and highpass current transfer functions from the same configuration without changing the circuit configuration and elements. The natural angular frequency we and the parameter wo/Q can be orthogonally controlled through adjusting the transconductance gain of OTA. PSPICE simulation results are employed to confirm the circuit performance.